[U-Boot] [PATCH 1/4] powerpc/85xx: Move PCI/PCIe address defines into common immap_85xx.h
Remove dupliacted setting of PCI/PCIe address and offsets in board config.h.
Signed-off-by: Kumar Gala galak@kernel.crashing.org --- arch/powerpc/include/asm/immap_85xx.h | 20 ++++++++++++++++++++ include/configs/ATUM8548.h | 3 --- include/configs/MPC8536DS.h | 5 ----- include/configs/MPC8544DS.h | 5 ----- include/configs/MPC8548CDS.h | 4 ---- include/configs/MPC8568MDS.h | 3 --- include/configs/MPC8569MDS.h | 3 --- include/configs/MPC8572DS.h | 4 ---- include/configs/P1022DS.h | 4 ---- include/configs/P1_P2_RDB.h | 3 --- include/configs/P2020DS.h | 4 ---- include/configs/TQM85xx.h | 4 ---- include/configs/XPEDITE5200.h | 1 - include/configs/XPEDITE5370.h | 2 -- include/configs/sbc8548.h | 4 ---- 15 files changed, 20 insertions(+), 49 deletions(-)
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index a37bc80..ac9b7ab 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -2092,8 +2092,17 @@ typedef struct ccsr_sec { #define CONFIG_SYS_MPC85xx_LBC_OFFSET 0x5000 #define CONFIG_SYS_MPC85xx_DDR2_OFFSET 0x6000 #define CONFIG_SYS_MPC85xx_ESPI_OFFSET 0x7000 +#define CONFIG_SYS_MPC85xx_PCI1_OFFSET 0x8000 #define CONFIG_SYS_MPC85xx_PCIX_OFFSET 0x8000 +#define CONFIG_SYS_MPC85xx_PCI2_OFFSET 0x9000 #define CONFIG_SYS_MPC85xx_PCIX2_OFFSET 0x9000 +#define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0xa000 +#define CONFIG_SYS_MPC85xx_PCIE2_OFFSET 0x9000 +#if defined(CONFIG_MPC8572) || defined(CONFIG_P2020) +#define CONFIG_SYS_MPC85xx_PCIE3_OFFSET 0x8000 +#else +#define CONFIG_SYS_MPC85xx_PCIE3_OFFSET 0xb000 +#endif #define CONFIG_SYS_MPC85xx_GPIO_OFFSET 0xF000 #define CONFIG_SYS_MPC85xx_SATA1_OFFSET 0x18000 #define CONFIG_SYS_MPC85xx_SATA2_OFFSET 0x19000 @@ -2176,6 +2185,17 @@ typedef struct ccsr_sec { #define CONFIG_SYS_FSL_SEC_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_SEC_OFFSET)
+#define CONFIG_SYS_PCI1_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PCI1_OFFSET) +#define CONFIG_SYS_PCI2_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PCI2_OFFSET) +#define CONFIG_SYS_PCIE1_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PCIE1_OFFSET) +#define CONFIG_SYS_PCIE2_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PCIE2_OFFSET) +#define CONFIG_SYS_PCIE3_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PCIE3_OFFSET) + #define TSEC_BASE_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET) #define MDIO_BASE_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MDIO1_OFFSET)
diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h index 49a86fd..c133033 100644 --- a/include/configs/ATUM8548.h +++ b/include/configs/ATUM8548.h @@ -91,9 +91,6 @@ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define PCI_SPEED 33333000 /* CPLD currenlty does not have PCI setup info */ -#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
/* DDR Setup */ #define CONFIG_FSL_DDR2 diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 9c46d3e..f03d707 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -129,11 +129,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #endif
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) -#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) -#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR + 0xb000) - /* DDR Setup */ #define CONFIG_VERY_BIG_RAM #define CONFIG_FSL_DDR2 diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index faba353..96fd024 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -79,11 +79,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) -#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) -#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0xb000) - /* DDR Setup */ #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index fdd3597..23594a7 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -80,10 +80,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) - /* DDR Setup */ #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 0cc2d47..bc6c5c7 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -75,9 +75,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) - /* DDR Setup */ #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index bb7bb47..92c2b49 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -103,9 +103,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #endif
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) - /* DDR Setup */ #define CONFIG_FSL_DDR3 #undef CONFIG_FSL_DDR_INTERACTIVE diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 6038de1..8dfc3cf 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -93,10 +93,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #endif #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) - /* DDR Setup */ #define CONFIG_VERY_BIG_RAM #define CONFIG_FSL_DDR2 diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index e444179..3ed188f 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -60,10 +60,6 @@ #define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
-#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) /* pci0 */ -#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) /* pci1 */ -#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR + 0xb000) /* pci2 */ - /* DDR Setup */ #define CONFIG_DDR_SPD #define CONFIG_VERY_BIG_RAM diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 3cebbab..fca3cdd 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -129,9 +129,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #endif
-#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) - /* DDR Setup */ #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index 569da4f..bf2acbf 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -90,10 +90,6 @@ #endif #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) - /* DDR Setup */ #define CONFIG_VERY_BIG_RAM #define CONFIG_FSL_DDR3 1 diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index 90abe14..d8f2602 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -137,10 +137,6 @@ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000) -#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) - /* * DDR Setup */ diff --git a/include/configs/XPEDITE5200.h b/include/configs/XPEDITE5200.h index df5ef78..83aeffd 100644 --- a/include/configs/XPEDITE5200.h +++ b/include/configs/XPEDITE5200.h @@ -81,7 +81,6 @@ #define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ -#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000)
/* * Diagnostics diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h index 1d6091c..fc4a986 100644 --- a/include/configs/XPEDITE5370.h +++ b/include/configs/XPEDITE5370.h @@ -99,8 +99,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) -#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000)
/* * Diagnostics diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 3f4056e..c8b8d0d 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -109,10 +109,6 @@ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) - /* DDR Setup */ #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE
Remove dupliacted setting of PCI/PCIe address and offsets in board config.h. Renamed CONFIG_SYS_PCI1/2_ADDR to CONFIG_SYS_PCI1/2ADDR on MPC8641 boards since its really PCIE controllers and not PCI.
Signed-off-by: Kumar Gala galak@kernel.crashing.org --- arch/powerpc/include/asm/immap_86xx.h | 17 +++++++++++++++++ board/freescale/mpc8641hpcn/mpc8641hpcn.c | 4 ++-- board/sbc8641d/sbc8641d.c | 4 ++-- include/configs/MPC8610HPCD.h | 4 ---- include/configs/MPC8641HPCN.h | 3 --- include/configs/XPEDITE5170.h | 2 -- include/configs/sbc8641d.h | 3 --- 7 files changed, 21 insertions(+), 16 deletions(-)
diff --git a/arch/powerpc/include/asm/immap_86xx.h b/arch/powerpc/include/asm/immap_86xx.h index b9e02db..4bebb68 100644 --- a/arch/powerpc/include/asm/immap_86xx.h +++ b/arch/powerpc/include/asm/immap_86xx.h @@ -1257,6 +1257,23 @@ extern immap_t *immr; #define CONFIG_SYS_MPC86xx_DMA_OFFSET (0x21000) #define CONFIG_SYS_MPC86xx_DMA_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_DMA_OFFSET)
+#define CONFIG_SYS_MPC86xx_PCI1_OFFSET 0x8000 +#ifdef CONFIG_MPC8610 +#define CONFIG_SYS_MPC86xx_PCIE1_OFFSET 0xa000 +#else +#define CONFIG_SYS_MPC86xx_PCIE1_OFFSET 0x8000 +#endif +#define CONFIG_SYS_MPC86xx_PCIE2_OFFSET 0x9000 + +#define CONFIG_SYS_PCI1_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_PCI1_OFFSET) +#define CONFIG_SYS_PCI2_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_PCI2_OFFSET) +#define CONFIG_SYS_PCIE1_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_PCIE1_OFFSET) +#define CONFIG_SYS_PCIE2_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_PCIE2_OFFSET) + #define CONFIG_SYS_TSEC1_OFFSET 0x24000 #define CONFIG_SYS_MDIO1_OFFSET 0x24000 #define CONFIG_SYS_LBC_ADDR (&((immap_t *)CONFIG_SYS_IMMR)->im_lbc) diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c index b352c33..9e88102 100644 --- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c +++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c @@ -142,7 +142,7 @@ void pci_init_board(void) { #ifdef CONFIG_PCI1 { - volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR; + volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; struct pci_controller *hose = &pci1_hose; struct pci_region *r = hose->regions; volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR; @@ -208,7 +208,7 @@ void pci_init_board(void)
#ifdef CONFIG_PCI2 { - volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI2_ADDR; + volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; struct pci_controller *hose = &pci2_hose; struct pci_region *r = hose->regions;
diff --git a/board/sbc8641d/sbc8641d.c b/board/sbc8641d/sbc8641d.c index c4e9875..1060f38 100644 --- a/board/sbc8641d/sbc8641d.c +++ b/board/sbc8641d/sbc8641d.c @@ -214,7 +214,7 @@ void pci_init_board(void)
#ifdef CONFIG_PCI1 { - volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR; + volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; struct pci_controller *hose = &pci1_hose; struct pci_region *r = hose->regions; #ifdef DEBUG @@ -268,7 +268,7 @@ void pci_init_board(void)
#ifdef CONFIG_PCI2 { - volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI2_ADDR; + volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; struct pci_controller *hose = &pci2_hose; struct pci_region *r = hose->regions;
diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 8382e3c..4d9606e 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -82,10 +82,6 @@ #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) -#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) - #define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR+0x2c000)
/* DDR Setup */ diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 94e4d24..b183e02 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -122,9 +122,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW #endif
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) - /* * DDR Setup */ diff --git a/include/configs/XPEDITE5170.h b/include/configs/XPEDITE5170.h index c63fd42..8770a8d 100644 --- a/include/configs/XPEDITE5170.h +++ b/include/configs/XPEDITE5170.h @@ -97,8 +97,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR -#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000) -#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000)
/* * Diagnostics diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 315eebe..6662bbe 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -108,9 +108,6 @@ #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) -#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) - /* * DDR Setup */
The MPC8641 boards actually only have PCIE not PCI. Rename so we are uniform with regards to names so we can replace this code with templated code.
Signed-off-by: Kumar Gala galak@kernel.crashing.org --- board/freescale/mpc8641hpcn/law.c | 18 +++--- board/freescale/mpc8641hpcn/mpc8641hpcn.c | 58 ++++++++++---------- board/sbc8641d/law.c | 16 +++--- board/sbc8641d/sbc8641d.c | 52 +++++++++--------- include/configs/MPC8641HPCN.h | 80 ++++++++++++++--------------- include/configs/sbc8641d.h | 50 +++++++++--------- 6 files changed, 136 insertions(+), 138 deletions(-)
diff --git a/board/freescale/mpc8641hpcn/law.c b/board/freescale/mpc8641hpcn/law.c index bd357b8..8c8ce95 100644 --- a/board/freescale/mpc8641hpcn/law.c +++ b/board/freescale/mpc8641hpcn/law.c @@ -1,5 +1,5 @@ /* - * Copyright 2008 Freescale Semiconductor, Inc. + * Copyright 2008,2010 Freescale Semiconductor, Inc. * * (C) Copyright 2000 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. @@ -32,14 +32,14 @@ * * 0x0000_0000 0x7fff_ffff DDR 2G * if PCI (prepend 0xc_0000_0000 if CONFIG_PHYS_64BIT) - * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M - * 0xa000_0000 0xbfff_ffff PCI2 MEM 512M + * 0x8000_0000 0x9fff_ffff PCIE1 MEM 512M + * 0xa000_0000 0xbfff_ffff PCIE2 MEM 512M * else if RIO (prepend 0xc_0000_0000 if CONFIG_PHYS_64BIT) * 0x8000_0000 0x9fff_ffff RapidIO 512M * endif * (prepend 0xf_0000_0000 if CONFIG_PHYS_64BIT) - * 0xffc0_0000 0xffc0_ffff PCI1 IO 64K - * 0xffc1_0000 0xffc1_ffff PCI2 IO 64K + * 0xffc0_0000 0xffc0_ffff PCIE1 IO 64K + * 0xffc1_0000 0xffc1_ffff PCIE2 IO 64K * 0xffe0_0000 0xffef_ffff CCSRBAR 1M * 0xffdf_0000 0xffe0_0000 PIXIS, CF 64K * 0xef80_0000 0xefff_ffff FLASH (boot bank) 8M @@ -54,10 +54,10 @@ struct law_entry law_table[] = { SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR_1), #endif #ifdef CONFIG_PCI - SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1), - SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), - SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_1), - SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_2), #elif defined(CONFIG_RIO) SET_LAW(CONFIG_SYS_RIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO), #endif diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c index 9e88102..a88be5a 100644 --- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c +++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c @@ -1,5 +1,5 @@ /* - * Copyright 2006, 2007 Freescale Semiconductor. + * Copyright 2006, 2007, 2010 Freescale Semiconductor. * * See file CREDITS for list of people who contributed to this * project. @@ -129,21 +129,21 @@ fixed_sdram(void)
#if defined(CONFIG_PCI) -static struct pci_controller pci1_hose; +static struct pci_controller pcie1_hose; #endif /* CONFIG_PCI */
-#ifdef CONFIG_PCI2 -static struct pci_controller pci2_hose; -#endif /* CONFIG_PCI2 */ +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif /* CONFIG_PCIE2 */
int first_free_busno = 0;
void pci_init_board(void) { -#ifdef CONFIG_PCI1 +#ifdef CONFIG_PCIE1 { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; - struct pci_controller *hose = &pci1_hose; + struct pci_controller *hose = &pcie1_hose; struct pci_region *r = hose->regions; volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR; volatile ccsr_gur_t *gur = &immap->im_gur; @@ -169,16 +169,16 @@ void pci_init_board(void)
/* outbound memory */ pci_set_region(r++, - CONFIG_SYS_PCI1_MEM_BUS, - CONFIG_SYS_PCI1_MEM_PHYS, - CONFIG_SYS_PCI1_MEM_SIZE, + CONFIG_SYS_PCIE1_MEM_BUS, + CONFIG_SYS_PCIE1_MEM_PHYS, + CONFIG_SYS_PCIE1_MEM_SIZE, PCI_REGION_MEM);
/* outbound io */ pci_set_region(r++, - CONFIG_SYS_PCI1_IO_BUS, - CONFIG_SYS_PCI1_IO_PHYS, - CONFIG_SYS_PCI1_IO_SIZE, + CONFIG_SYS_PCIE1_IO_BUS, + CONFIG_SYS_PCIE1_IO_PHYS, + CONFIG_SYS_PCIE1_IO_SIZE, PCI_REGION_IO);
hose->region_count = r - hose->regions; @@ -195,8 +195,8 @@ void pci_init_board(void) * Activate ULI1575 legacy chip by performing a fake * memory access. Needed to make ULI RTC work. */ - in_be32((unsigned *) ((char *)(CONFIG_SYS_PCI1_MEM_VIRT - + CONFIG_SYS_PCI1_MEM_SIZE - 0x1000000))); + in_be32((unsigned *) ((char *)(CONFIG_SYS_PCIE1_MEM_VIRT + + CONFIG_SYS_PCIE1_MEM_SIZE - 0x1000000)));
} else { puts("PCI-EXPRESS 1: Disabled\n"); @@ -204,26 +204,26 @@ void pci_init_board(void) } #else puts("PCI-EXPRESS1: Disabled\n"); -#endif /* CONFIG_PCI1 */ +#endif /* CONFIG_PCIE1 */
-#ifdef CONFIG_PCI2 +#ifdef CONFIG_PCIE2 { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; - struct pci_controller *hose = &pci2_hose; + struct pci_controller *hose = &pcie2_hose; struct pci_region *r = hose->regions;
/* outbound memory */ pci_set_region(r++, - CONFIG_SYS_PCI2_MEM_BUS, - CONFIG_SYS_PCI2_MEM_PHYS, - CONFIG_SYS_PCI2_MEM_SIZE, + CONFIG_SYS_PCIE2_MEM_BUS, + CONFIG_SYS_PCIE2_MEM_PHYS, + CONFIG_SYS_PCIE2_MEM_SIZE, PCI_REGION_MEM);
/* outbound io */ pci_set_region(r++, - CONFIG_SYS_PCI2_IO_BUS, - CONFIG_SYS_PCI2_IO_PHYS, - CONFIG_SYS_PCI2_IO_SIZE, + CONFIG_SYS_PCIE2_IO_BUS, + CONFIG_SYS_PCIE2_IO_PHYS, + CONFIG_SYS_PCIE2_IO_SIZE, PCI_REGION_IO);
hose->region_count = r - hose->regions; @@ -238,7 +238,7 @@ void pci_init_board(void) } #else puts("PCI-EXPRESS 2: Disabled\n"); -#endif /* CONFIG_PCI2 */ +#endif /* CONFIG_PCIE2 */
}
@@ -253,11 +253,11 @@ ft_board_setup(void *blob, bd_t *bd)
ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); +#ifdef CONFIG_PCIE1 + ft_fsl_pci_setup(blob, "pci0", &pcie1_hose); #endif -#ifdef CONFIG_PCI2 - ft_fsl_pci_setup(blob, "pci1", &pci2_hose); +#ifdef CONFIG_PCIE2 + ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); #endif
/* diff --git a/board/sbc8641d/law.c b/board/sbc8641d/law.c index d20fa51..705e1c2 100644 --- a/board/sbc8641d/law.c +++ b/board/sbc8641d/law.c @@ -32,11 +32,11 @@ * * 0x0000_0000 DDR 256M * 0x1000_0000 DDR2 256M - * 0x8000_0000 PCI1 MEM 512M - * 0xa000_0000 PCI2 MEM 512M + * 0x8000_0000 PCIE1 MEM 512M + * 0xa000_0000 PCIE2 MEM 512M * 0xc000_0000 RapidIO 512M - * 0xe200_0000 PCI1 IO 16M - * 0xe300_0000 PCI2 IO 16M + * 0xe200_0000 PCIE1 IO 16M + * 0xe300_0000 PCIE2 IO 16M * 0xf800_0000 CCSRBAR 2M * 0xfe00_0000 FLASH (boot bank) 32M * @@ -49,11 +49,11 @@ struct law_entry law_table[] = { SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, LAW_SIZE_256M, LAW_TRGT_IF_DDR_2), #endif - SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1), - SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), SET_LAW(0xf8000000, LAW_SIZE_2M, LAW_TRGT_IF_LBC), - SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_1), - SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_2), SET_LAW(0xfe000000, LAW_SIZE_32M, LAW_TRGT_IF_LBC), SET_LAW(CONFIG_SYS_RIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO) }; diff --git a/board/sbc8641d/sbc8641d.c b/board/sbc8641d/sbc8641d.c index 1060f38..b1dda10 100644 --- a/board/sbc8641d/sbc8641d.c +++ b/board/sbc8641d/sbc8641d.c @@ -191,16 +191,16 @@ static struct pci_config_table pci_fsl86xxads_config_table[] = { }; #endif
-static struct pci_controller pci1_hose = { +static struct pci_controller pcie1_hose = { #ifndef CONFIG_PCI_PNP config_table:pci_mpc86xxcts_config_table #endif }; #endif /* CONFIG_PCI */
-#ifdef CONFIG_PCI2 -static struct pci_controller pci2_hose; -#endif /* CONFIG_PCI2 */ +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif /* CONFIG_PCIE2 */
int first_free_busno = 0;
@@ -212,10 +212,10 @@ void pci_init_board(void) uint io_sel = (gur->pordevsr & MPC8641_PORDEVSR_IO_SEL) >> MPC8641_PORDEVSR_IO_SEL_SHIFT;
-#ifdef CONFIG_PCI1 +#ifdef CONFIG_PCIE1 { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; - struct pci_controller *hose = &pci1_hose; + struct pci_controller *hose = &pcie1_hose; struct pci_region *r = hose->regions; #ifdef DEBUG uint host1_agent = (gur->porbmsr & MPC8641_PORBMSR_HA) @@ -236,16 +236,16 @@ void pci_init_board(void)
/* outbound memory */ pci_set_region(r++, - CONFIG_SYS_PCI1_MEM_BUS, - CONFIG_SYS_PCI1_MEM_PHYS, - CONFIG_SYS_PCI1_MEM_SIZE, + CONFIG_SYS_PCIE1_MEM_BUS, + CONFIG_SYS_PCIE1_MEM_PHYS, + CONFIG_SYS_PCIE1_MEM_SIZE, PCI_REGION_MEM);
/* outbound io */ pci_set_region(r++, - CONFIG_SYS_PCI1_IO_BUS, - CONFIG_SYS_PCI1_IO_PHYS, - CONFIG_SYS_PCI1_IO_SIZE, + CONFIG_SYS_PCIE1_IO_BUS, + CONFIG_SYS_PCIE1_IO_PHYS, + CONFIG_SYS_PCIE1_IO_SIZE, PCI_REGION_IO);
hose->region_count = r - hose->regions; @@ -264,26 +264,26 @@ void pci_init_board(void) } #else puts("PCI-EXPRESS1: Disabled\n"); -#endif /* CONFIG_PCI1 */ +#endif /* CONFIG_PCIE1 */
-#ifdef CONFIG_PCI2 +#ifdef CONFIG_PCIE2 { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; - struct pci_controller *hose = &pci2_hose; + struct pci_controller *hose = &pcie2_hose; struct pci_region *r = hose->regions;
/* outbound memory */ pci_set_region(r++, - CONFIG_SYS_PCI2_MEM_BUS, - CONFIG_SYS_PCI2_MEM_PHYS, - CONFIG_SYS_PCI2_MEM_SIZE, + CONFIG_SYS_PCIE2_MEM_BUS, + CONFIG_SYS_PCIE2_MEM_PHYS, + CONFIG_SYS_PCIE2_MEM_SIZE, PCI_REGION_MEM);
/* outbound io */ pci_set_region(r++, - CONFIG_SYS_PCI2_IO_BUS, - CONFIG_SYS_PCI2_IO_PHYS, - CONFIG_SYS_PCI2_IO_SIZE, + CONFIG_SYS_PCIE2_IO_BUS, + CONFIG_SYS_PCIE2_IO_PHYS, + CONFIG_SYS_PCIE2_IO_SIZE, PCI_REGION_IO);
hose->region_count = r - hose->regions; @@ -298,7 +298,7 @@ void pci_init_board(void) } #else puts("PCI-EXPRESS 2: Disabled\n"); -#endif /* CONFIG_PCI2 */ +#endif /* CONFIG_PCIE2 */
}
@@ -308,11 +308,11 @@ void ft_board_setup (void *blob, bd_t *bd) { ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); +#ifdef CONFIG_PCIE1 + ft_fsl_pci_setup(blob, "pci0", &pcie1_hose); #endif -#ifdef CONFIG_PCI2 - ft_fsl_pci_setup(blob, "pci1", &pci2_hose); +#ifdef CONFIG_PCIE2 + ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); #endif } #endif diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index b183e02..0d1f779 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -1,5 +1,5 @@ /* - * Copyright 2006 Freescale Semiconductor. + * Copyright 2006, 2010 Freescale Semiconductor. * * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) * @@ -58,8 +58,8 @@
#ifndef CONFIG_RIO /* RIO/PCI are mutually exclusive */ #define CONFIG_PCI 1 /* Enable PCI/PCIE */ -#define CONFIG_PCI1 1 /* PCIE controler 1 (ULI bridge) */ -#define CONFIG_PCI2 1 /* PCIE controler 2 (slot) */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 (ULI bridge) */ +#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #endif @@ -325,43 +325,43 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * Addresses are mapped 1-1. */
-#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCI1_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0x0000000c00000000ULL +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0x0000000c00000000ULL #else -#define CONFIG_SYS_PCI1_MEM_BUS CONFIG_SYS_PCI1_MEM_VIRT -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_VIRT +#define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_VIRT #endif -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_VIRT 0xffc00000 -#define CONFIG_SYS_PCI1_IO_PHYS (CONFIG_SYS_PCI1_IO_VIRT \ +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE1_IO_PHYS (CONFIG_SYS_PCIE1_IO_VIRT \ | CONFIG_SYS_PHYS_ADDR_HIGH) -#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64K */ +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */
#ifdef CONFIG_PHYS_64BIT /* - * Use the same PCI bus address on PCI1 and PCI2 if we have PHYS_64BIT. + * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. * This will increase the amount of PCI address space available for * for mapping RAM. */ -#define CONFIG_SYS_PCI2_MEM_BUS CONFIG_SYS_PCI1_MEM_BUS +#define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS #else -#define CONFIG_SYS_PCI2_MEM_BUS (CONFIG_SYS_PCI1_MEM_BUS \ - + CONFIG_SYS_PCI1_MEM_SIZE) +#define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ + + CONFIG_SYS_PCIE1_MEM_SIZE) #endif -#define CONFIG_SYS_PCI2_MEM_VIRT (CONFIG_SYS_PCI1_MEM_VIRT \ - + CONFIG_SYS_PCI1_MEM_SIZE) -#define CONFIG_SYS_PCI2_MEM_PHYS (CONFIG_SYS_PCI1_MEM_PHYS \ - + CONFIG_SYS_PCI1_MEM_SIZE) -#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI2_IO_VIRT (CONFIG_SYS_PCI1_IO_VIRT \ - + CONFIG_SYS_PCI1_IO_SIZE) -#define CONFIG_SYS_PCI2_IO_PHYS (CONFIG_SYS_PCI1_IO_PHYS \ - + CONFIG_SYS_PCI1_IO_SIZE) -#define CONFIG_SYS_PCI2_IO_SIZE CONFIG_SYS_PCI1_IO_SIZE +#define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ + + CONFIG_SYS_PCIE1_MEM_SIZE) +#define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ + + CONFIG_SYS_PCIE1_MEM_SIZE) +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ + + CONFIG_SYS_PCIE1_IO_SIZE) +#define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ + + CONFIG_SYS_PCIE1_IO_SIZE) +#define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE
#if defined(CONFIG_PCI)
@@ -390,10 +390,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
/*PCIE video card used*/ -#define VIDEO_IO_OFFSET CONFIG_SYS_PCI2_IO_VIRT +#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT
/*PCI video card used*/ -/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ +/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/
/* video */ #define CONFIG_VIDEO @@ -406,7 +406,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_ATI_RADEON_FB #define CONFIG_VIDEO_LOGO /*#define CONFIG_CONSOLE_CURSOR*/ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCI2_IO_VIRT +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT #endif
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ @@ -422,8 +422,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE #endif
-#define CONFIG_MPC86XX_PCI2 - #endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET) @@ -494,17 +492,17 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
/* if CONFIG_PCI: - * BAT2 PCI1 and PCI1 MEM + * BAT2 PCIE1 and PCIE1 MEM * if CONFIG_RIO * BAT2 Rapidio Memory */ #ifdef CONFIG_PCI -#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \ +#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS) \ | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G \ +#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \ +#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS) \ | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U #else /* CONFIG_RIO */ @@ -553,14 +551,14 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif
/* - * BAT4 PCI1_IO and PCI2_IO + * BAT4 PCIE1_IO and PCIE2_IO */ -#define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \ +#define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS) \ | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_128K \ +#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \ +#define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS) \ | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 6662bbe..618513a 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -56,8 +56,8 @@ #define CONFIG_SYS_SCRATCH_VA 0xe8000000
#define CONFIG_PCI 1 /* Enable PCIE */ -#define CONFIG_PCI1 1 /* PCIE controler 1 (slot 1) */ -#define CONFIG_PCI2 1 /* PCIE controler 2 (slot 2) */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */
@@ -304,23 +304,23 @@ * General PCI * Addresses are mapped 1-1. */ -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS -#define CONFIG_SYS_PCI1_MEM_VIRT CONFIG_SYS_PCI1_MEM_BUS -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_BUS 0xe2000000 -#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BUS -#define CONFIG_SYS_PCI1_IO_VIRT CONFIG_SYS_PCI1_IO_BUS -#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ - -#define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BUS -#define CONFIG_SYS_PCI2_MEM_VIRT CONFIG_SYS_PCI2_MEM_BUS -#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_IO_BUS 0xe3000000 -#define CONFIG_SYS_PCI2_IO_PHYS CONFIG_SYS_PCI2_IO_BUS -#define CONFIG_SYS_PCI2_IO_VIRT CONFIG_SYS_PCI2_IO_BUS -#define CONFIG_SYS_PCI2_IO_SIZE 0x1000000 /* 16M */ +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS +#define CONFIG_SYS_PCIE1_MEM_VIRT CONFIG_SYS_PCIE1_MEM_BUS +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BUS 0xe2000000 +#define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BUS +#define CONFIG_SYS_PCIE1_IO_VIRT CONFIG_SYS_PCIE1_IO_BUS +#define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */ + +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS +#define CONFIG_SYS_PCIE2_MEM_VIRT CONFIG_SYS_PCIE2_MEM_BUS +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_BUS 0xe3000000 +#define CONFIG_SYS_PCIE2_IO_PHYS CONFIG_SYS_PCIE2_IO_BUS +#define CONFIG_SYS_PCIE2_IO_VIRT CONFIG_SYS_PCIE2_IO_BUS +#define CONFIG_SYS_PCIE2_IO_SIZE 0x1000000 /* 16M */
#if defined(CONFIG_PCI)
@@ -406,10 +406,10 @@ * 0xa000_0000 512M PCI-Express 2 Memory * Changed it for operating from 0xd0000000 */ -#define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW \ +#define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
/* @@ -449,10 +449,10 @@ * 0xe300_0000 16M PCI-Express 2 I/0 * Note that this is at 0xe0000000 */ -#define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW \ +#define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_32M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_32M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
/*
Previously we used an alias the pci node to determine which node to fixup or delete. Now we use the new fdt_node_offset_by_compat_reg to find the node to update.
Additionally, we replace the code in each board with a single macro call that makes assumes uniform naming and reduces duplication in this area.
Signed-off-by: Kumar Gala galak@kernel.crashing.org --- arch/powerpc/include/asm/fsl_pci.h | 84 +++++++++++++++++++++++++++- board/atum8548/atum8548.c | 10 +--- board/freescale/mpc8536ds/mpc8536ds.c | 22 +------- board/freescale/mpc8544ds/mpc8544ds.c | 15 +----- board/freescale/mpc8548cds/mpc8548cds.c | 9 +--- board/freescale/mpc8568mds/mpc8568mds.c | 9 +--- board/freescale/mpc8569mds/mpc8569mds.c | 7 +-- board/freescale/mpc8572ds/mpc8572ds.c | 13 +---- board/freescale/mpc8610hpcd/mpc8610hpcd.c | 12 +---- board/freescale/mpc8641hpcn/mpc8641hpcn.c | 7 +-- board/freescale/p1022ds/p1022ds.c | 18 +------ board/freescale/p1_p2_rdb/pci.c | 15 +----- board/freescale/p2020ds/p2020ds.c | 13 +---- board/sbc8548/sbc8548.c | 8 +-- board/sbc8641d/sbc8641d.c | 7 +-- board/tqc/tqm85xx/tqm85xx.c | 7 +-- board/xes/common/fsl_8xxx_pci.c | 14 +----- drivers/pci/fsl_pci_init.c | 15 ++++-- 18 files changed, 122 insertions(+), 163 deletions(-)
diff --git a/arch/powerpc/include/asm/fsl_pci.h b/arch/powerpc/include/asm/fsl_pci.h index bb87543..dc5c579 100644 --- a/arch/powerpc/include/asm/fsl_pci.h +++ b/arch/powerpc/include/asm/fsl_pci.h @@ -1,5 +1,5 @@ /* - * Copyright 2007,2009 Freescale Semiconductor, Inc. + * Copyright 2007,2009-2010 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -29,8 +29,8 @@ int fsl_setup_hose(struct pci_controller *hose, unsigned long addr); int fsl_is_pci_agent(struct pci_controller *hose); void fsl_pci_init(struct pci_controller *hose, u32 cfg_addr, u32 cfg_data); void fsl_pci_config_unlock(struct pci_controller *hose); -void ft_fsl_pci_setup(void *blob, const char *pci_alias, - struct pci_controller *hose); +void ft_fsl_pci_setup(void *blob, const char *pci_compat, + struct pci_controller *hose, unsigned long ctrl_addr);
/* * Common PCI/PCIE Register structure for mpc85xx and mpc86xx @@ -202,4 +202,82 @@ int fsl_pci_init_port(struct fsl_pci_info *pci_info, x.pci_num = num; \ }
+#define __FT_FSL_PCI_SETUP(blob, compat, num) \ + ft_fsl_pci_setup(blob, compat, &pci##num##_hose, \ + CONFIG_SYS_PCI##num##_ADDR) + +#define __FT_FSL_PCI_DEL(blob, compat, num) \ + ft_fsl_pci_setup(blob, compat, NULL, CONFIG_SYS_PCI##num##_ADDR) + +#define __FT_FSL_PCIE_SETUP(blob, compat, num) \ + ft_fsl_pci_setup(blob, compat, &pcie##num##_hose, \ + CONFIG_SYS_PCIE##num##_ADDR) + +#define __FT_FSL_PCIE_DEL(blob, compat, num) \ + ft_fsl_pci_setup(blob, compat, NULL, CONFIG_SYS_PCIE##num##_ADDR) + +#ifdef CONFIG_PCI1 +#define FT_FSL_PCI1_SETUP __FT_FSL_PCI_SETUP(blob, FSL_PCI_COMPAT, 1) +#else +#define FT_FSL_PCI1_SETUP __FT_FSL_PCI_DEL(blob, FSL_PCI_COMPAT, 1) +#endif + +#ifdef CONFIG_PCI2 +#define FT_FSL_PCI2_SETUP __FT_FSL_PCI_SETUP(blob, FSL_PCI_COMPAT, 2) +#else +#define FT_FSL_PCI2_SETUP __FT_FSL_PCI_DEL(blob, FSL_PCI_COMPAT, 2) +#endif + +#ifdef CONFIG_PCIE1 +#define FT_FSL_PCIE1_SETUP __FT_FSL_PCIE_SETUP(blob, FSL_PCIE_COMPAT, 1) +#else +#define FT_FSL_PCIE1_SETUP __FT_FSL_PCIE_DEL(blob, FSL_PCIE_COMPAT, 1) +#endif + +#ifdef CONFIG_PCIE2 +#define FT_FSL_PCIE2_SETUP __FT_FSL_PCIE_SETUP(blob, FSL_PCIE_COMPAT, 2) +#else +#define FT_FSL_PCIE2_SETUP __FT_FSL_PCIE_DEL(blob, FSL_PCIE_COMPAT, 2) +#endif + +#ifdef CONFIG_PCIE3 +#define FT_FSL_PCIE3_SETUP __FT_FSL_PCIE_SETUP(blob, FSL_PCIE_COMPAT, 3) +#else +#define FT_FSL_PCIE3_SETUP __FT_FSL_PCIE_DEL(blob, FSL_PCIE_COMPAT, 3) +#endif + +#ifdef CONFIG_PCIE4 +#define FT_FSL_PCIE4_SETUP __FT_FSL_PCIE_SETUP(blob, FSL_PCIE_COMPAT, 4) +#else +#define FT_FSL_PCIE4_SETUP __FT_FSL_PCIE_DEL(blob, FSL_PCIE_COMPAT, 4) +#endif + +#if defined(CONFIG_FSL_CORENET) +#define FSL_PCIE_COMPAT "fsl,p4080-pcie" +#define FT_FSL_PCI_SETUP \ + FT_FSL_PCIE1_SETUP; \ + FT_FSL_PCIE2_SETUP; \ + FT_FSL_PCIE3_SETUP; \ + FT_FSL_PCIE4_SETUP; +#elif defined(CONFIG_MPC85xx) +#define FSL_PCI_COMPAT "fsl,mpc8540-pci" +#define FSL_PCIE_COMPAT "fsl,mpc8548-pcie" +#define FT_FSL_PCI_SETUP \ + FT_FSL_PCI1_SETUP; \ + FT_FSL_PCI2_SETUP; \ + FT_FSL_PCIE1_SETUP; \ + FT_FSL_PCIE2_SETUP; \ + FT_FSL_PCIE3_SETUP; +#elif defined(CONFIG_MPC86xx) +#define FSL_PCI_COMPAT "fsl,mpc8610-pci" +#define FSL_PCIE_COMPAT "fsl,mpc8641-pcie" +#define FT_FSL_PCI_SETUP \ + FT_FSL_PCI1_SETUP; \ + FT_FSL_PCIE1_SETUP; \ + FT_FSL_PCIE2_SETUP; +#else +#error FT_FSL_PCI_SETUP not defined +#endif + + #endif diff --git a/board/atum8548/atum8548.c b/board/atum8548/atum8548.c index 4f7d935..671f9e9 100644 --- a/board/atum8548/atum8548.c +++ b/board/atum8548/atum8548.c @@ -292,14 +292,6 @@ void ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#endif -#ifdef CONFIG_PCI2 - ft_fsl_pci_setup(blob, "pci1", &pci2_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); -#endif + FT_FSL_PCI_SETUP; } #endif diff --git a/board/freescale/mpc8536ds/mpc8536ds.c b/board/freescale/mpc8536ds/mpc8536ds.c index 1968106..93af7f8 100644 --- a/board/freescale/mpc8536ds/mpc8536ds.c +++ b/board/freescale/mpc8536ds/mpc8536ds.c @@ -544,26 +544,8 @@ void ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#else - ft_fsl_pci_setup(blob, "pci0", NULL); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); -#else - ft_fsl_pci_setup(blob, "pci1", NULL); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); -#else - ft_fsl_pci_setup(blob, "pci2", NULL); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci3", &pcie3_hose); -#else - ft_fsl_pci_setup(blob, "pci3", NULL); -#endif + FT_FSL_PCI_SETUP; + #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c index 581d5f2..da3a2b6 100644 --- a/board/freescale/mpc8544ds/mpc8544ds.c +++ b/board/freescale/mpc8544ds/mpc8544ds.c @@ -1,5 +1,5 @@ /* - * Copyright 2007,2009 Freescale Semiconductor, Inc. + * Copyright 2007,2009-2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -360,19 +360,8 @@ void ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd);
+ FT_FSL_PCI_SETUP;
-#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci2", &pcie3_hose); -#endif -#ifdef CONFIG_PCIE3 - ft_fsl_pci_setup(blob, "pci3", &pcie2_hose); -#endif #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif diff --git a/board/freescale/mpc8548cds/mpc8548cds.c b/board/freescale/mpc8548cds/mpc8548cds.c index f016995..23e552b 100644 --- a/board/freescale/mpc8548cds/mpc8548cds.c +++ b/board/freescale/mpc8548cds/mpc8548cds.c @@ -1,5 +1,5 @@ /* - * Copyright 2004, 2007, 200 Freescale Semiconductor, Inc. + * Copyright 2004, 2007, 2009-2010 Freescale Semiconductor, Inc. * * (C) Copyright 2002 Scott McNutt smcnutt@artesyncp.com * @@ -388,11 +388,6 @@ int last_stage_init(void) #if defined(CONFIG_OF_BOARD_SETUP) void ft_pci_setup(void *blob, bd_t *bd) { -#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); -#endif + FT_FSL_PCI_SETUP; } #endif diff --git a/board/freescale/mpc8568mds/mpc8568mds.c b/board/freescale/mpc8568mds/mpc8568mds.c index 036bf95..bd859e4 100644 --- a/board/freescale/mpc8568mds/mpc8568mds.c +++ b/board/freescale/mpc8568mds/mpc8568mds.c @@ -1,5 +1,5 @@ /* - * Copyright 2007,2009 Freescale Semiconductor, Inc. + * Copyright 2007,2009-2010 Freescale Semiconductor, Inc. * * (C) Copyright 2002 Scott McNutt smcnutt@artesyncp.com * @@ -426,11 +426,6 @@ void ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); -#endif + FT_FSL_PCI_SETUP; } #endif diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c index 81e8ff5..01b7dcb 100644 --- a/board/freescale/mpc8569mds/mpc8569mds.c +++ b/board/freescale/mpc8569mds/mpc8569mds.c @@ -1,5 +1,5 @@ /* - * Copyright 2009 Freescale Semiconductor. + * Copyright 2009-2010 Freescale Semiconductor. * * (C) Copyright 2002 Scott McNutt smcnutt@artesyncp.com * @@ -635,9 +635,8 @@ void ft_board_setup(void *blob, bd_t *bd) #endif ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); -#endif + FT_FSL_PCI_SETUP; + fdt_board_fixup_esdhc(blob, bd); fdt_board_fixup_qe_uart(blob, bd); fdt_board_fixup_qe_usb(blob, bd); diff --git a/board/freescale/mpc8572ds/mpc8572ds.c b/board/freescale/mpc8572ds/mpc8572ds.c index 6029a51..4d0050f 100644 --- a/board/freescale/mpc8572ds/mpc8572ds.c +++ b/board/freescale/mpc8572ds/mpc8572ds.c @@ -1,5 +1,5 @@ /* - * Copyright 2007-2009 Freescale Semiconductor, Inc. + * Copyright 2007-2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -488,15 +488,8 @@ void ft_board_setup(void *blob, bd_t *bd)
fdt_fixup_memory(blob, (u64)base, (u64)size);
-#ifdef CONFIG_PCIE3 - ft_fsl_pci_setup(blob, "pci0", &pcie3_hose); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); -#endif + FT_FSL_PCI_SETUP; + #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd.c b/board/freescale/mpc8610hpcd/mpc8610hpcd.c index 2ef7b23..6578f58 100644 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd.c +++ b/board/freescale/mpc8610hpcd/mpc8610hpcd.c @@ -1,5 +1,5 @@ /* - * Copyright 2007,2009 Freescale Semiconductor, Inc. + * Copyright 2007,2009-2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -309,15 +309,7 @@ ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci2", &pcie2_hose); -#endif + FT_FSL_PCI_SETUP; } #endif
diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c index a88be5a..d86ca12 100644 --- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c +++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c @@ -253,12 +253,7 @@ ft_board_setup(void *blob, bd_t *bd)
ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci0", &pcie1_hose); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); -#endif + FT_FSL_PCI_SETUP;
/* * Warn if it looks like the device tree doesn't match u-boot. diff --git a/board/freescale/p1022ds/p1022ds.c b/board/freescale/p1022ds/p1022ds.c index 8cc73ed..43f6d35 100644 --- a/board/freescale/p1022ds/p1022ds.c +++ b/board/freescale/p1022ds/p1022ds.c @@ -322,23 +322,7 @@ void ft_board_setup(void *blob, bd_t *bd)
fdt_fixup_memory(blob, (u64)base, (u64)size);
-#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci0", &pcie1_hose); -#else - ft_fsl_pci_setup(blob, "pci0", NULL); -#endif - -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); -#else - ft_fsl_pci_setup(blob, "pci1", NULL); -#endif - -#ifdef CONFIG_PCIE3 - ft_fsl_pci_setup(blob, "pci2", &pcie3_hose); -#else - ft_fsl_pci_setup(blob, "pci2", NULL); -#endif + FT_FSL_PCI_SETUP;
#ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); diff --git a/board/freescale/p1_p2_rdb/pci.c b/board/freescale/p1_p2_rdb/pci.c index aa2f64c..97d4f83 100644 --- a/board/freescale/p1_p2_rdb/pci.c +++ b/board/freescale/p1_p2_rdb/pci.c @@ -1,5 +1,5 @@ /* - * Copyright 2009 Freescale Semiconductor, Inc. + * Copyright 2009-2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -100,16 +100,5 @@ void pci_init_board(void)
void ft_pci_board_setup(void *blob) { -/* According to h/w manual, PCIE2 is at lower address(0x9000) - * than PCIE1(0xa000). - * Hence PCIE2 is made to occupy the pci1 position in dts to - * keep the addresses sorted there. - * Generally the case with all FSL SOCs. - */ -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); -#endif + FT_FSL_PCI_SETUP; } diff --git a/board/freescale/p2020ds/p2020ds.c b/board/freescale/p2020ds/p2020ds.c index be4b2eb..3fd1b34 100644 --- a/board/freescale/p2020ds/p2020ds.c +++ b/board/freescale/p2020ds/p2020ds.c @@ -1,5 +1,5 @@ /* - * Copyright 2007-2009 Freescale Semiconductor, Inc. + * Copyright 2007-2010 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -366,15 +366,8 @@ void ft_board_setup(void *blob, bd_t *bd)
fdt_fixup_memory(blob, (u64)base, (u64)size);
-#ifdef CONFIG_PCIE3 - ft_fsl_pci_setup(blob, "pci0", &pcie3_hose); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); -#endif + FT_FSL_PCI_SETUP; + #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c index d62cfd1..733979c 100644 --- a/board/sbc8548/sbc8548.c +++ b/board/sbc8548/sbc8548.c @@ -398,11 +398,9 @@ int last_stage_init(void) void ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); -#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); + +#ifdef CONFIG_FSL_PCI_INIT + FT_FSL_PCI_SETUP; #endif } #endif diff --git a/board/sbc8641d/sbc8641d.c b/board/sbc8641d/sbc8641d.c index b1dda10..54b2d0b 100644 --- a/board/sbc8641d/sbc8641d.c +++ b/board/sbc8641d/sbc8641d.c @@ -308,12 +308,7 @@ void ft_board_setup (void *blob, bd_t *bd) { ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci0", &pcie1_hose); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); -#endif + FT_FSL_PCI_SETUP; } #endif
diff --git a/board/tqc/tqm85xx/tqm85xx.c b/board/tqc/tqm85xx/tqm85xx.c index fc2a6cb..dda2cb6 100644 --- a/board/tqc/tqm85xx/tqm85xx.c +++ b/board/tqc/tqm85xx/tqm85xx.c @@ -687,12 +687,7 @@ void ft_board_setup (void *blob, bd_t *bd) { ft_cpu_setup (blob, bd);
-#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); -#endif + FT_FSL_PCI_SETUP; } #endif /* CONFIG_OF_BOARD_SETUP */
diff --git a/board/xes/common/fsl_8xxx_pci.c b/board/xes/common/fsl_8xxx_pci.c index 3a81827..ece7882 100644 --- a/board/xes/common/fsl_8xxx_pci.c +++ b/board/xes/common/fsl_8xxx_pci.c @@ -398,18 +398,6 @@ void pci_init_board(void) #if defined(CONFIG_OF_BOARD_SETUP) void ft_board_pci_setup(void *blob, bd_t *bd) { - /* TODO - make node name (eg pci0) dynamic */ -#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); -#endif -#ifdef CONFIG_PCIE1 - ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); -#endif -#ifdef CONFIG_PCIE2 - ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); -#endif -#ifdef CONFIG_PCIE3 - ft_fsl_pci_setup(blob, "pci0", &pcie3_hose); -#endif + FT_FSL_PCI_SETUP; } #endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c index 5a63fa2..001e6eb 100644 --- a/drivers/pci/fsl_pci_init.c +++ b/drivers/pci/fsl_pci_init.c @@ -510,18 +510,25 @@ void fsl_pci_config_unlock(struct pci_controller *hose) #include <libfdt.h> #include <fdt_support.h>
-void ft_fsl_pci_setup(void *blob, const char *pci_alias, - struct pci_controller *hose) +void ft_fsl_pci_setup(void *blob, const char *pci_compat, + struct pci_controller *hose, unsigned long ctrl_addr) { - int off = fdt_path_offset(blob, pci_alias); + int off; u32 bus_range[2]; + phys_addr_t p_ctrl_addr = (phys_addr_t)ctrl_addr; + + /* convert ctrl_addr to true physical address */ + p_ctrl_addr = (phys_addr_t)ctrl_addr - CONFIG_SYS_CCSRBAR; + p_ctrl_addr += CONFIG_SYS_CCSRBAR_PHYS; + + off = fdt_node_offset_by_compat_reg(blob, pci_compat, p_ctrl_addr);
if (off < 0) return;
/* We assume a cfg_addr not being set means we didn't setup the controller */ if ((hose == NULL) || (hose->cfg_addr == NULL)) { - fdt_del_node_and_alias(blob, pci_alias); + fdt_del_node(blob, off); } else { bus_range[0] = 0; bus_range[1] = hose->last_busno - hose->first_busno;
On Jul 9, 2010, at 12:18 AM, Kumar Gala wrote:
Previously we used an alias the pci node to determine which node to fixup or delete. Now we use the new fdt_node_offset_by_compat_reg to find the node to update.
Additionally, we replace the code in each board with a single macro call that makes assumes uniform naming and reduces duplication in this area.
Signed-off-by: Kumar Gala galak@kernel.crashing.org
arch/powerpc/include/asm/fsl_pci.h | 84 +++++++++++++++++++++++++++- board/atum8548/atum8548.c | 10 +--- board/freescale/mpc8536ds/mpc8536ds.c | 22 +------- board/freescale/mpc8544ds/mpc8544ds.c | 15 +----- board/freescale/mpc8548cds/mpc8548cds.c | 9 +--- board/freescale/mpc8568mds/mpc8568mds.c | 9 +--- board/freescale/mpc8569mds/mpc8569mds.c | 7 +-- board/freescale/mpc8572ds/mpc8572ds.c | 13 +---- board/freescale/mpc8610hpcd/mpc8610hpcd.c | 12 +---- board/freescale/mpc8641hpcn/mpc8641hpcn.c | 7 +-- board/freescale/p1022ds/p1022ds.c | 18 +------ board/freescale/p1_p2_rdb/pci.c | 15 +----- board/freescale/p2020ds/p2020ds.c | 13 +---- board/sbc8548/sbc8548.c | 8 +-- board/sbc8641d/sbc8641d.c | 7 +-- board/tqc/tqm85xx/tqm85xx.c | 7 +-- board/xes/common/fsl_8xxx_pci.c | 14 +----- drivers/pci/fsl_pci_init.c | 15 ++++-- 18 files changed, 122 insertions(+), 163 deletions(-)
applied to 85xx
- k
On Fri, Jul 9, 2010 at 12:18 AM, Kumar Gala galak@kernel.crashing.org wrote:
The MPC8641 boards actually only have PCIE not PCI. Rename so we are uniform with regards to names so we can replace this code with templated code.
The subject line of this patch is backwards. It should be "Rename PCIE1/2 to PCI1/2".
Personally, I would drop the "1/2" as well.
On Jul 9, 2010, at 9:14 AM, Timur Tabi wrote:
On Fri, Jul 9, 2010 at 12:18 AM, Kumar Gala galak@kernel.crashing.org wrote:
The MPC8641 boards actually only have PCIE not PCI. Rename so we are uniform with regards to names so we can replace this code with templated code.
The subject line of this patch is backwards. It should be "Rename PCIE1/2 to PCI1/2".
Huh, I'm going from PCI1 -> PCIE1
Personally, I would drop the "1/2" as well.
-- Timur Tabi Linux kernel developer at Freescale
- k
On Fri, Jul 9, 2010 at 9:20 AM, Kumar Gala galak@kernel.crashing.org wrote:
Huh, I'm going from PCI1 -> PCIE1
Sorry, I got confused. I really should stop reading patches before I had my coffee.
On Jul 9, 2010, at 12:18 AM, Kumar Gala wrote:
The MPC8641 boards actually only have PCIE not PCI. Rename so we are uniform with regards to names so we can replace this code with templated code.
Signed-off-by: Kumar Gala galak@kernel.crashing.org
board/freescale/mpc8641hpcn/law.c | 18 +++--- board/freescale/mpc8641hpcn/mpc8641hpcn.c | 58 ++++++++++---------- board/sbc8641d/law.c | 16 +++--- board/sbc8641d/sbc8641d.c | 52 +++++++++--------- include/configs/MPC8641HPCN.h | 80 ++++++++++++++--------------- include/configs/sbc8641d.h | 50 +++++++++--------- 6 files changed, 136 insertions(+), 138 deletions(-)
applied to 85xx
- k
On Jul 9, 2010, at 12:18 AM, Kumar Gala wrote:
Remove dupliacted setting of PCI/PCIe address and offsets in board config.h. Renamed CONFIG_SYS_PCI1/2_ADDR to CONFIG_SYS_PCI1/2ADDR on MPC8641 boards since its really PCIE controllers and not PCI.
Signed-off-by: Kumar Gala galak@kernel.crashing.org
arch/powerpc/include/asm/immap_86xx.h | 17 +++++++++++++++++ board/freescale/mpc8641hpcn/mpc8641hpcn.c | 4 ++-- board/sbc8641d/sbc8641d.c | 4 ++-- include/configs/MPC8610HPCD.h | 4 ---- include/configs/MPC8641HPCN.h | 3 --- include/configs/XPEDITE5170.h | 2 -- include/configs/sbc8641d.h | 3 --- 7 files changed, 21 insertions(+), 16 deletions(-)
applied to 85xx
- k
On Jul 9, 2010, at 12:18 AM, Kumar Gala wrote:
Remove dupliacted setting of PCI/PCIe address and offsets in board config.h.
Signed-off-by: Kumar Gala galak@kernel.crashing.org
arch/powerpc/include/asm/immap_85xx.h | 20 ++++++++++++++++++++ include/configs/ATUM8548.h | 3 --- include/configs/MPC8536DS.h | 5 ----- include/configs/MPC8544DS.h | 5 ----- include/configs/MPC8548CDS.h | 4 ---- include/configs/MPC8568MDS.h | 3 --- include/configs/MPC8569MDS.h | 3 --- include/configs/MPC8572DS.h | 4 ---- include/configs/P1022DS.h | 4 ---- include/configs/P1_P2_RDB.h | 3 --- include/configs/P2020DS.h | 4 ---- include/configs/TQM85xx.h | 4 ---- include/configs/XPEDITE5200.h | 1 - include/configs/XPEDITE5370.h | 2 -- include/configs/sbc8548.h | 4 ---- 15 files changed, 20 insertions(+), 49 deletions(-)
applied to 85xx
- k
participants (2)
-
Kumar Gala -
Timur Tabi