Add basic suport for the Freescale P1022DS reference board.

Specifics:

1) 36-bit only 2) Booting from NOR flash only 3) Environment stored in NOR flash only 4) No SPI support 5) No DIU support

Signed-off-by: Timur Tabi timur@freescale.com ---

This patch is for the 'next' branch.

v3: Fixed minor issues, ported to new makefile format

v2: addresses most of Wolfgang's concerns. DIU support removed so that it can be reworked later

This depends on the following patches:

Move ICS CLK chip frequenty calculation code into a common board library fsl: add LAW target to fsl_pci_info structure

MAINTAINERS | 1 + MAKEALL | 1 + arch/powerpc/cpu/mpc85xx/Makefile | 1 + arch/powerpc/cpu/mpc85xx/p1022_serdes.c | 166 +++++++++++ arch/powerpc/include/asm/fsl_serdes.h | 2 + board/freescale/common/Makefile | 1 + board/freescale/p1022ds/Makefile | 39 +++ board/freescale/p1022ds/config.mk | 14 + board/freescale/p1022ds/ddr.c | 106 +++++++ board/freescale/p1022ds/law.c | 21 ++ board/freescale/p1022ds/p1022ds.c | 285 +++++++++++++++++++ board/freescale/p1022ds/tlb.c | 76 +++++ boards.cfg | 1 + include/configs/P1022DS.h | 470 +++++++++++++++++++++++++++++++ 14 files changed, 1184 insertions(+), 0 deletions(-) create mode 100644 arch/powerpc/cpu/mpc85xx/p1022_serdes.c create mode 100644 board/freescale/p1022ds/Makefile create mode 100644 board/freescale/p1022ds/config.mk create mode 100644 board/freescale/p1022ds/ddr.c create mode 100644 board/freescale/p1022ds/law.c create mode 100644 board/freescale/p1022ds/p1022ds.c create mode 100644 board/freescale/p1022ds/tlb.c create mode 100644 include/configs/P1022DS.h

diff --git a/MAINTAINERS b/MAINTAINERS index 7a13d28..d702f0d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -437,6 +437,7 @@ Timur Tabi timur@freescale.com

MPC8349E-mITX MPC8349 MPC8349E-mITX-GP MPC8349 + P1022DS P1022

Erik Theisen etheisen@mindspring.com

diff --git a/MAKEALL b/MAKEALL index 2527352..858f7d4 100755 --- a/MAKEALL +++ b/MAKEALL @@ -406,6 +406,7 @@ LIST_85xx=" \ MPC8569MDS_NAND \ MPC8572DS \ MPC8572DS_36BIT \ + P1022DS \ P2020DS \ P2020DS_36BIT \ P1011RDB \ diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile index f064fee..a481326 100644 --- a/arch/powerpc/cpu/mpc85xx/Makefile +++ b/arch/powerpc/cpu/mpc85xx/Makefile @@ -63,6 +63,7 @@ COBJS-$(CONFIG_CPM2) += ether_fcc.o COBJS-$(CONFIG_OF_LIBFDT) += fdt.o COBJS-$(CONFIG_MP) += mp.o COBJS-$(CONFIG_MPC8536) += mpc8536_serdes.o +COBJS-$(CONFIG_P1022) += p1022_serdes.o COBJS-$(CONFIG_PCI) += pci.o COBJS-$(CONFIG_QE) += qe_io.o COBJS-$(CONFIG_CPM2) += serial_scc.o diff --git a/arch/powerpc/cpu/mpc85xx/p1022_serdes.c b/arch/powerpc/cpu/mpc85xx/p1022_serdes.c new file mode 100644 index 0000000..52e109b --- /dev/null +++ b/arch/powerpc/cpu/mpc85xx/p1022_serdes.c @@ -0,0 +1,166 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * Author: Timur Tabi timur@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <config.h> +#include <common.h> +#include <asm/io.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_serdes.h> + +#define SRDS1_MAX_LANES 4 +#define SRDS2_MAX_LANES 2 + +static const u8 serdes1_cfg_tbl[][SRDS1_MAX_LANES] = { + [0x00] = {NONE, NONE, NONE, NONE}, + [0x01] = {NONE, NONE, NONE, NONE}, + [0x02] = {NONE, NONE, NONE, NONE}, + [0x03] = {NONE, NONE, NONE, NONE}, + [0x04] = {NONE, NONE, NONE, NONE}, + [0x06] = {PCIE1, PCIE3, SGMII_TSEC1, PCIE2}, + [0x07] = {PCIE1, PCIE3, SGMII_TSEC1, PCIE2}, + [0x09] = {PCIE1, NONE, NONE, NONE}, + [0x0a] = {PCIE1, PCIE3, SGMII_TSEC1, SGMII_TSEC2}, + [0x0b] = {PCIE1, PCIE3, SGMII_TSEC1, SGMII_TSEC2}, + [0x0d] = {PCIE1, PCIE1, SGMII_TSEC1, SGMII_TSEC2}, + [0x0e] = {PCIE1, PCIE1, SGMII_TSEC1, SGMII_TSEC2}, + [0x0f] = {PCIE1, PCIE1, SGMII_TSEC1, SGMII_TSEC2}, + [0x15] = {PCIE1, PCIE3, PCIE2, PCIE2}, + [0x16] = {PCIE1, PCIE3, PCIE2, PCIE2}, + [0x17] = {PCIE1, PCIE3, PCIE2, PCIE2}, + [0x18] = {PCIE1, PCIE1, PCIE2, PCIE2}, + [0x19] = {PCIE1, PCIE1, PCIE2, PCIE2}, + [0x1a] = {PCIE1, PCIE1, PCIE2, PCIE2}, + [0x1b] = {PCIE1, PCIE1, PCIE2, PCIE2}, + [0x1c] = {PCIE1, PCIE1, PCIE1, PCIE1}, + [0x1d] = {PCIE1, PCIE1, PCIE2, PCIE2}, + [0x1e] = {PCIE1, PCIE1, PCIE2, PCIE2}, + [0x1f] = {PCIE1, PCIE1, PCIE2, PCIE2}, +}; + +static const u8 serdes2_cfg_tbl[][SRDS2_MAX_LANES] = { + [0x00] = {PCIE3, PCIE3}, + [0x01] = {PCIE2, PCIE3}, + [0x02] = {SATA1, SATA2}, + [0x03] = {SGMII_TSEC1, SGMII_TSEC2}, + [0x04] = {NONE, NONE}, + [0x06] = {SATA1, SATA2}, + [0x07] = {NONE, NONE}, + [0x09] = {PCIE3, PCIE2}, + [0x0a] = {SATA1, SATA2}, + [0x0b] = {NONE, NONE}, + [0x0d] = {PCIE3, PCIE2}, + [0x0e] = {SATA1, SATA2}, + [0x0f] = {NONE, NONE}, + [0x15] = {SGMII_TSEC1, SGMII_TSEC2}, + [0x16] = {SATA1, SATA2}, + [0x17] = {NONE, NONE}, + [0x18] = {PCIE3, PCIE3}, + [0x19] = {SGMII_TSEC1, SGMII_TSEC2}, + [0x1a] = {SATA1, SATA2}, + [0x1b] = {NONE, NONE}, + [0x1c] = {PCIE3, PCIE3}, + [0x1d] = {SGMII_TSEC1, SGMII_TSEC2}, + [0x1e] = {SATA1, SATA2}, + [0x1f] = {NONE, NONE}, +}; + +/* + * A list of PCI and SATA slots + */ +enum slot_id { + SLOT_PCIE1 = 1, + SLOT_PCIE2, + SLOT_PCIE3, + SLOT_PCIE4, + SLOT_PCIE5, + SLOT_SATA1, + SLOT_SATA2 +}; + +/* + * This array maps the slot identifiers to their names on the P1022DS board. + */ +static const char *slot_names[] = { + [SLOT_PCIE1] = "Slot 1", + [SLOT_PCIE2] = "Slot 2", + [SLOT_PCIE3] = "Slot 3", + [SLOT_PCIE4] = "Slot 4", + [SLOT_PCIE5] = "Mini-PCIe", + [SLOT_SATA1] = "SATA 1", + [SLOT_SATA2] = "SATA 2", +}; + +/* + * This array maps a given SERDES configuration and SERDES device to the PCI or + * SATA slot that it connects to. This mapping is hard-coded in the FPGA. + */ +static u8 serdes_dev_slot[][SATA2 + 1] = { + [0x01] = { [PCIE3] = SLOT_PCIE4, [PCIE2] = SLOT_PCIE5 }, + [0x02] = { [SATA1] = SLOT_SATA1, [SATA2] = SLOT_SATA2 }, + [0x09] = { [PCIE1] = SLOT_PCIE1, [PCIE3] = SLOT_PCIE4, + [PCIE2] = SLOT_PCIE5 }, + [0x16] = { [PCIE1] = SLOT_PCIE1, [PCIE3] = SLOT_PCIE2, + [PCIE2] = SLOT_PCIE3, + [SATA1] = SLOT_SATA1, [SATA2] = SLOT_SATA2 }, + [0x17] = { [PCIE1] = SLOT_PCIE1, [PCIE3] = SLOT_PCIE2, + [PCIE2] = SLOT_PCIE3 }, + [0x1a] = { [PCIE1] = SLOT_PCIE1, [PCIE2] = SLOT_PCIE3, + [PCIE2] = SLOT_PCIE3, + [SATA1] = SLOT_SATA1, [SATA2] = SLOT_SATA2 }, + [0x1c] = { [PCIE1] = SLOT_PCIE1, + [SATA1] = SLOT_SATA1, [SATA2] = SLOT_SATA2 }, + [0x1e] = { [PCIE1] = SLOT_PCIE1, [PCIE3] = SLOT_PCIE3 }, + [0x1f] = { [PCIE1] = SLOT_PCIE1 }, +}; + +int is_serdes_configured(enum srds_prtcl device) +{ + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + u32 pordevsr = in_be32(&gur->pordevsr); + u32 srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> + MPC85xx_PORDEVSR_IO_SEL_SHIFT; + unsigned int i; + + debug("%s: dev = %d\n", __FUNCTION__, device); + debug("PORDEVSR[IO_SEL] = 0x%x\n", srds_cfg); + + if (srds_cfg > ARRAY_SIZE(serdes1_cfg_tbl)) { + printf("Invalid PORDEVSR[IO_SEL] = %d\n", srds_cfg); + return 0; + } + + for (i = 0; i < SRDS1_MAX_LANES; i++) { + if (serdes1_cfg_tbl[srds_cfg][i] == device) + return 1; + if (serdes2_cfg_tbl[srds_cfg][i] == device) + return 1; + } + + return 0; +} + +/* + * Returns the name of the slot to which the PCIe or SATA controller is + * connected + */ +const char *serdes_slot_name(enum srds_prtcl device) +{ + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + u32 pordevsr = in_be32(&gur->pordevsr); + unsigned int srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> + MPC85xx_PORDEVSR_IO_SEL_SHIFT; + enum slot_id slot = serdes_dev_slot[srds_cfg][device]; + const char *name = slot_names[slot]; + + if (name) + return name; + else + return "Nothing"; +} diff --git a/arch/powerpc/include/asm/fsl_serdes.h b/arch/powerpc/include/asm/fsl_serdes.h index d4839f4..2056532 100644 --- a/arch/powerpc/include/asm/fsl_serdes.h +++ b/arch/powerpc/include/asm/fsl_serdes.h @@ -45,4 +45,6 @@ enum srds_prtcl {

int is_serdes_configured(enum srds_prtcl device);

+const char *serdes_slot_name(enum srds_prtcl device); + #endif /* __FSL_SERDES_H */ diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index d18445b..5436bd6 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -42,6 +42,7 @@ COBJS-$(CONFIG_MPC8541CDS) += cds_pci_ft.o COBJS-$(CONFIG_MPC8548CDS) += cds_pci_ft.o COBJS-$(CONFIG_MPC8555CDS) += cds_pci_ft.o

+COBJS-$(CONFIG_P1022DS) += ics307_clk.o COBJS-$(CONFIG_P2020DS) += ics307_clk.o

SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) diff --git a/board/freescale/p1022ds/Makefile b/board/freescale/p1022ds/Makefile new file mode 100644 index 0000000..8ede2d6 --- /dev/null +++ b/board/freescale/p1022ds/Makefile @@ -0,0 +1,39 @@ +# +# Copyright 2010 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/p1022ds/config.mk b/board/freescale/p1022ds/config.mk new file mode 100644 index 0000000..4581d20 --- /dev/null +++ b/board/freescale/p1022ds/config.mk @@ -0,0 +1,14 @@ +# +# Copyright 2010 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. +# + +ifndef TEXT_BASE +TEXT_BASE = 0xeff80000 +endif + +RESET_VECTOR_ADDRESS = 0xeffffffc diff --git a/board/freescale/p1022ds/ddr.c b/board/freescale/p1022ds/ddr.c new file mode 100644 index 0000000..7ecfb3e --- /dev/null +++ b/board/freescale/p1022ds/ddr.c @@ -0,0 +1,106 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * Authors: Srikanth Srinivasan srikanth.srinivasan@freescale.com + * Timur Tabi timur@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <i2c.h> + +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd, unsigned int ctrl_num) +{ + int ret; + + /* + * The P1022 has only one DDR controller, and the board has only one + * DIMM slot. + */ + ret = i2c_read(SPD_EEPROM_ADDRESS1, 0, 1, (u8 *)ctrl_dimms_spd, + sizeof(ddr3_spd_eeprom_t)); + if (ret) { + debug("DDR: failed to read SPD from address %u\n", + SPD_EEPROM_ADDRESS1); + memset(ctrl_dimms_spd, 0, sizeof(ddr3_spd_eeprom_t)); + } +} + +typedef struct { + u32 datarate_mhz_low; + u32 datarate_mhz_high; + u32 n_ranks; + u32 clk_adjust; /* Range: 0-8 */ + u32 cpo; /* Range: 2-31 */ + u32 write_data_delay; /* Range: 0-6 */ + u32 force_2T; +} board_specific_parameters_t; + +static const board_specific_parameters_t bsp[] = { +/* + * lo| hi| num| clk| cpo|wrdata|2T + * mhz| mhz|ranks|adjst| | delay| + */ + { 0, 333, 1, 5, 31, 3, 0}, + {334, 400, 1, 5, 31, 3, 0}, + {401, 549, 1, 5, 31, 3, 0}, + {550, 680, 1, 5, 31, 5, 0}, + {681, 850, 1, 5, 31, 5, 0}, + { 0, 333, 2, 5, 31, 3, 0}, + {334, 400, 2, 5, 31, 3, 0}, + {401, 549, 2, 5, 31, 3, 0}, + {550, 680, 2, 5, 31, 5, 0}, + {681, 850, 2, 5, 31, 5, 0}, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + unsigned long ddr_freq; + unsigned int i; + + /* set odt_rd_cfg and odt_wr_cfg. */ + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + popts->cs_local_opts[i].odt_rd_cfg = 0; + popts->cs_local_opts[i].odt_wr_cfg = 1; + } + + /* + * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + for (i = 0; i < ARRAY_SIZE(bsp); i++) { + if (ddr_freq >= bsp[i].datarate_mhz_low && + ddr_freq <= bsp[i].datarate_mhz_high && + pdimm->n_ranks == bsp[i].n_ranks) { + popts->clk_adjust = bsp[i].clk_adjust; + popts->cpo_override = bsp[i].cpo; + popts->write_data_delay = bsp[i].write_data_delay; + popts->twoT_en = bsp[i].force_2T; + break; + } + } + + popts->half_strength_driver_enable = 1; + + /* Per AN4039, enable ZQ calibration. */ + popts->zq_en = 1; + + /* + * For wake-up on ARP, we need auto self refresh enabled + */ + popts->auto_self_refresh_en = 1; + popts->sr_it = 0xb; +} diff --git a/board/freescale/p1022ds/law.c b/board/freescale/p1022ds/law.c new file mode 100644 index 0000000..b23b8f9 --- /dev/null +++ b/board/freescale/p1022ds/law.c @@ -0,0 +1,21 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * Authors: Srikanth Srinivasan srikanth.srinivasan@freescale.com + * Timur Tabi timur@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1022ds/p1022ds.c b/board/freescale/p1022ds/p1022ds.c new file mode 100644 index 0000000..e374b3a --- /dev/null +++ b/board/freescale/p1022ds/p1022ds.c @@ -0,0 +1,285 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * Authors: Srikanth Srinivasan srikanth.srinivasan@freescale.com + * Timur Tabi timur@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_serdes.h> +#include <asm/io.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <tsec.h> +#include <asm/fsl_law.h> +#include <asm/mp.h> +#include <netdev.h> +#include <i2c.h> + +#include "../common/ngpixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + /* Set pmuxcr to allow both i2c1 and i2c2 */ + setbits_be32(&gur->pmuxcr, 0x1000); + + /* Read back the register to synchronize the write. */ + in_be32(&gur->pmuxcr); + + /* Set the pin muxing to enable ETSEC2. */ + clrbits_be32(&gur->pmuxcr2, 0x001F8000); + + return 0; +} + +int checkboard(void) +{ + u8 sw; + + puts("Board: P1022DS "); + + printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", + in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver)); + + sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH)); + + switch ((sw & PIXIS_LBMAP_MASK) >> 6) { + case 0: + printf ("vBank: %u\n", ((sw & 0x30) >> 4)); + break; + case 1: + printf ("NAND\n"); + break; + case 2: + case 3: + puts ("Promjet\n"); + break; + } + + return 0; +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size = 0; + + puts("Initializing....\n"); + + dram_size = fsl_ddr_sdram(); + dram_size = setup_ddr_tlbs(dram_size / 0x100000) * 0x100000; + + puts(" DDR: "); + return dram_size; +} + +#define CONFIG_TFP410_I2C_ADDR 0x38 + +int misc_init_r(void) +{ + u8 temp; + + /* Enable the TFP410 Encoder */ + + temp = 0xBF; + if (i2c_write(CONFIG_TFP410_I2C_ADDR, 0x08, 1, &temp, sizeof(temp)) < 0) + return -1; + + /* Verify if enabled */ + temp = 0; + if (i2c_read(CONFIG_TFP410_I2C_ADDR, 0x08, 1, &temp, sizeof(temp)) < 0) + return -1; + + debug("DVI Encoder Read: 0x%02x\n", temp); + + temp = 0x10; + if (i2c_write(CONFIG_TFP410_I2C_ADDR, 0x0A, 1, &temp, sizeof(temp)) < 0) + return -1; + + /* Verify if enabled */ + temp = 0; + if (i2c_read(CONFIG_TFP410_I2C_ADDR, 0x0A, 1, &temp, sizeof(temp)) < 0) + return -1; + + debug("DVI Encoder Read: 0x%02x\n",temp); + + return 0; +} + +static void configure_pcie(struct fsl_pci_info *info, + struct pci_controller *hose, + const char *connected) +{ + static int bus_number = 0; + int is_endpoint; + + set_next_law(info->mem_phys, law_size_bits(info->mem_size), info->law); + set_next_law(info->io_phys, law_size_bits(info->io_size), info->law); + is_endpoint = fsl_setup_hose(hose, info->regs); + printf(" PCIE%u connected to %s as %s (base addr %lx)\n", + info->pci_num, connected, + is_endpoint ? "Endpoint" : "Root Complex", info->regs); + bus_number = fsl_pci_init_port(info, hose, bus_number); +} + +#ifdef CONFIG_PCIE1 +static struct pci_controller pcie1_hose; +#endif + +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif + +#ifdef CONFIG_PCIE3 +static struct pci_controller pcie3_hose; +#endif + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + struct fsl_pci_info pci_info; + u32 devdisr = in_be32(&gur->devdisr); + +#ifdef CONFIG_PCIE1 + if (is_serdes_configured(PCIE1) && !(devdisr & MPC85xx_DEVDISR_PCIE)) { + SET_STD_PCIE_INFO(pci_info, 1); + configure_pcie(&pci_info, &pcie1_hose, serdes_slot_name(PCIE1)); + } else { + printf(" PCIE1: disabled\n"); + } +#else + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE); /* disable */ +#endif + +#ifdef CONFIG_PCIE2 + if (is_serdes_configured(PCIE2) && !(devdisr & MPC85xx_DEVDISR_PCIE2)) { + SET_STD_PCIE_INFO(pci_info, 2); + configure_pcie(&pci_info, &pcie2_hose, serdes_slot_name(PCIE2)); + } else { + printf(" PCIE2: disabled\n"); + } +#else + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE2); /* disable */ +#endif + +#ifdef CONFIG_PCIE3 + if (is_serdes_configured(PCIE3) && !(devdisr & MPC85xx_DEVDISR_PCIE3)) { + SET_STD_PCIE_INFO(pci_info, 3); + configure_pcie(&pci_info, &pcie3_hose, serdes_slot_name(PCIE3)); + } else { + printf(" PCIE3: disabled\n"); + } +#else + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE3); /* disable */ +#endif +} +#endif + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); + + return 0; +} + +/* + * Initialize on-board and/or PCI Ethernet devices + * + * Returns: + * <0, error + * 0, no ethernet devices found + * >0, number of ethernet devices initialized + */ +int board_eth_init(bd_t *bis) +{ + struct tsec_info_struct tsec_info[2]; + unsigned int num = 0; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + num++; +#endif + + return tsec_eth_init(bis, tsec_info, num) + pci_eth_init(bis); +} + +#ifdef CONFIG_OF_BOARD_SETUP +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCIE1 + ft_fsl_pci_setup(blob, "pci0", &pcie1_hose); +#else + ft_fsl_pci_setup(blob, "pci0", NULL); +#endif + +#ifdef CONFIG_PCIE2 + ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); +#else + ft_fsl_pci_setup(blob, "pci1", NULL); +#endif + +#ifdef CONFIG_PCIE3 + ft_fsl_pci_setup(blob, "pci2", &pcie3_hose); +#else + ft_fsl_pci_setup(blob, "pci2", NULL); +#endif + +#ifdef CONFIG_FSL_SGMII_RISER + fsl_sgmii_riser_fdt_fixup(blob); +#endif +} +#endif + +#ifdef CONFIG_MP +void board_lmb_reserve(struct lmb *lmb) +{ + cpu_mp_lmb_reserve(lmb); +} +#endif diff --git a/board/freescale/p1022ds/tlb.c b/board/freescale/p1022ds/tlb.c new file mode 100644 index 0000000..e620112 --- /dev/null +++ b/board/freescale/p1022ds/tlb.c @@ -0,0 +1,76 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * Authors: Srikanth Srinivasan srikanth.srinivasan@freescale.com + * Timur Tabi timur@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* W**G* - Flash/promjet, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000, + CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000, + CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), + + SET_TLB_ENTRY(1, PIXIS_BASE, PIXIS_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_4K, 1), +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index e54673e..bc75536 100644 --- a/boards.cfg +++ b/boards.cfg @@ -333,6 +333,7 @@ MPC8560ADS powerpc mpc85xx mpc8560ads freescale MPC8568MDS powerpc mpc85xx mpc8568mds freescale XPEDITE5200 powerpc mpc85xx xpedite5200 xes XPEDITE5370 powerpc mpc85xx xpedite5370 xes +P1022DS powerpc mpc85xx p1022ds freescale sbc8641d powerpc mpc86xx MPC8610HPCD powerpc mpc86xx mpc8610hpcd freescale XPEDITE5170 powerpc mpc86xx xpedite5170 xes diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h new file mode 100644 index 0000000..e444179 --- /dev/null +++ b/include/configs/P1022DS.h @@ -0,0 +1,470 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * Authors: Srikanth Srinivasan srikanth.srinivasan@freescale.com + * Timur Tabi timur@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include "../board/freescale/common/ics307_clk.h" + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx /* MPC8540/60/55/41/48 */ +#define CONFIG_P1022 +#define CONFIG_P1022DS +#define CONFIG_MP /* support multiple processors */ + +#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ +#define CONFIG_PCIE3 /* PCIE controler 3 (ULI bridge) */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_PHYS_64BIT +#define CONFIG_ENABLE_36BIT_PHYS +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() +#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE +#define CONFIG_BTB + +#define CONFIG_SYS_MEMTEST_START 0x00000000 +#define CONFIG_SYS_MEMTEST_END 0x7fffffff + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR + +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) /* pci0 */ +#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) /* pci1 */ +#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR + 0xb000) /* pci2 */ + +/* DDR Setup */ +#define CONFIG_DDR_SPD +#define CONFIG_VERY_BIG_RAM +#define CONFIG_FSL_DDR3 + +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) + +/* I2C addresses of SPD EEPROMs */ +#define CONFIG_SYS_SPD_BUS_NUM 1 +#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ + +/* + * Memory map + * + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable + * 0xffc0_0000 0xffc2_ffff PCI IO range 192K non-cacheable + * + * Localbus cacheable (TBD) + * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable + * + * Localbus non-cacheable + * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable + * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable + * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 + * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 + * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable + */ + +/* + * Local Bus Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ +#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull + +#define CONFIG_FLASH_BR_PRELIM \ + (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V) +#define CONFIG_FLASH_OR_PRELIM (OR_AM_128MB | 0xff7) + +#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ + +#define CONFIG_SYS_BR1_PRELIM \ + (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) +#define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM + +#define CONFIG_SYS_FLASH_BANKS_LIST \ + {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_MAX_FLASH_SECT 1024 + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_FSL_NGPIXIS +#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ +#define PIXIS_BASE_PHYS 0xfffdf0000ull + +#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB | 0x6ff7) + +#define PIXIS_LBMAP_SWITCH 7 +#define PIXIS_LBMAP_MASK 0xE0 +#define PIXIS_LBMAP_ALTBANK 0x20 + +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_FSL_DIU_FB +#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000) + +/* Video */ +/* #define CONFIG_VIDEO */ +#ifdef CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#endif + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE + +/* I2C */ +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, Slot 2, tgtid 1, Base address a000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 2, direct to uli, tgtid 2, Base address 9000 */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 3, Base address b000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +#ifdef CONFIG_PCI +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#endif + +/* SATA */ +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#ifdef CONFIG_FSL_SATA +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +#define CONFIG_MMC +#ifdef CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_GENERIC_MMC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#endif + +#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +#define CONFIG_TSEC_ENET +#ifdef CONFIG_TSEC_ENET + +#define CONFIG_TSECV2 +#define CONFIG_NET_MULTI + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" + +#define TSEC1_PHY_ADDR 1 +#define TSEC2_PHY_ADDR 2 + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OVERWRITE +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 + +#define CONFIG_LOADS_ECHO +#define CONFIG_SYS_LOADS_BAUD_CHANGE + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * USB + */ +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_STORAGE +#define CONFIG_CMD_FAT +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_HZ 1000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#define CONFIG_HOSTNAME p1022ds +#define CONFIG_ROOTPATH /opt/nfsroot +#define CONFIG_BOOTFILE uImage +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ + +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#define CONFIG_BOOTARGS + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "perf_mode=stable\0" \ + "memctl_intlv_ctl=2\0" \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=uramdisk\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=p1022ds.dtb\0" \ + "bdev=sda3\0" \ + "diuregs=md e002c000 1d\0" \ + "dium=mw e002c01c\0" \ + "diuerr=md e002c014 1\0" \ + "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 tty0\0" \ + "monitor=0-DVI\0" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND + +#endif