[U-Boot-Users] 4xx ethernet bringup
Hi All,
I am working on the 405GP custome board. I am able to bringup the SDRAM,Flash,I2c and serail on the board. But while trying to bringup the ethernet i am getting the following error. "No Ethernet found". On my board there is "DP83848I" PHY chip.
what exactely this is doing in lib_ppc/boarc.c s = getenv ("ethaddr"); #if defined (CONFIG_MBX) || \ defined (CONFIG_RPXCLASSIC) || \ defined(CONFIG_IAD210) || \ defined(CONFIG_V38B) if (s == NULL) board_get_enetaddr (bd->bi_enetaddr); else #endif for (i = 0; i < 6; ++i) { bd->bi_enetaddr[i] = s ? simple_strtoul (s, &e, 16) : 0; if (s) s = (*e) ? e + 1 : e; } #ifdef CONFIG_HERMES if ((gd->board_type >> 16) == 2) bd->bi_ethspeed = gd->board_type & 0xFFFF; else bd->bi_ethspeed = 0xFFFF; #endif
and in the same file there is one more call... #if (CONFIG_COMMANDS & CFG_CMD_NET) #if defined(CONFIG_NET_MULTI) WATCHDOG_RESET (); puts ("Net: "); #endif eth_initialize (bd); #endif
In the eth_initialize() function i see the print "No ethernet found". i reqeust you to please throw some out to come out of this problem......**********EXIT ME PLZ*************
Thanks Shami.
Why delete messages? Unlimited storage is just a click away. Go to http://help.yahoo.com/l/in/yahoo/mail/yahoomail/tools/tools-08.html
On Wednesday 19 December 2007, shami Allam wrote:
I am working on the 405GP custome board. I am able to bringup the SDRAM,Flash,I2c and serail on the board. But while trying to bringup the ethernet i am getting the following error. "No Ethernet found". On my board there is "DP83848I" PHY chip.
This message gets printed when you don't define the "ethaddr" environement address. So set this variable to a valid value and save the environment and reset the board. Then you should see one eth-interface.
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
Hi Stefan,
I assigned the ethaddr as 192.168.13.246 and after that i run the command "saveenv " and reset the board. I got the following Net: ppc_4xx_eth0. once i get the shell prompt i assign the ipaddr as 192.168.13.241 and after that i run the command "saveenv" and reset the board. Now i tried to ping my Host PC which has the IP address as 192.168.13.240, i am getting the following error.....I am not able to ping the host IP. Can you please show some way to come of this issue..... => ping 192.168.13.240 Trying ppc_4xx_eth0 PHY speed read failed, assuming 10bT PHY duplex read failed, assuming half duplex ENET Speed is 10 Mbps - HALF duplex connection Using ppc_4xx_eth0 device sending ARP for c0a80df0 ARP broadcast 1 ARP broadcast 2 ping failed; host 192.168.13.240 is not alive => Regards, Shami...
Stefan Roese sr@denx.de wrote: On Wednesday 19 December 2007, shami Allam wrote:
I am working on the 405GP custome board. I am able to bringup the SDRAM,Flash,I2c and serail on the board. But while trying to bringup the ethernet i am getting the following error. "No Ethernet found". On my board there is "DP83848I" PHY chip.
This message gets printed when you don't define the "ethaddr" environement address. So set this variable to a valid value and save the environment and reset the board. Then you should see one eth-interface.
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
--------------------------------- Get the freedom to save as many mails as you wish. Click here to know how.
In message 169884.69719.qm@web94113.mail.in2.yahoo.com you wrote:
I assigned the ethaddr as 192.168.13.246 and after that i run the command "saveenv " and reset the board. I got the following
That looks like an IP address to me.
A MAC address is something different. Please see http://en.wikipedia.org/wiki/MAC_address
Also make sure to read the FAQ.
Best regards,
Wolfgang Denk
Hi:
I am trying to boot 440EPx board similar to Seqouia from NAND. NAND flash is different from Sequoia's though, it has page size 2K, sector size 128K and it's 1Gb (128MB).
I set following parameters in my <board>.h file:
#define CFG_NAND_U_BOOT_SIZE (600 << 10) /* Size of RAM U-Boot image */
/* * Now the NAND chip has to be defined (no autodetection used!) */ #define CFG_NAND_PAGE_SIZE (2048) /* NAND chip page size */ #define CFG_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */ #define CFG_NAND_PAGE_COUNT (64) /* NAND chip page count */ #define CFG_NAND_BAD_BLOCK_POS (5) /* Location of bad block marker */ #define CFG_NAND_4_ADDR_CYCLE /* Fourth addr used (>32MB) */
but it doesn't boot.
Any suggestion? What is CFG_NAND_PAGE_COUNT anyway?
Thanks,
Leonid.
On Thursday 20 December 2007, Leonid wrote:
I am trying to boot 440EPx board similar to Seqouia from NAND. NAND flash is different from Sequoia's though, it has page size 2K, sector size 128K and it's 1Gb (128MB).
I set following parameters in my <board>.h file:
#define CFG_NAND_U_BOOT_SIZE (600 << 10) /* Size of RAM U-Boot image */
/*
- Now the NAND chip has to be defined (no autodetection used!)
*/ #define CFG_NAND_PAGE_SIZE (2048) /* NAND chip page size */ #define CFG_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */ #define CFG_NAND_PAGE_COUNT (64) /* NAND chip page count */ #define CFG_NAND_BAD_BLOCK_POS (5) /* Location of bad block marker */ #define CFG_NAND_4_ADDR_CYCLE /* Fourth addr used (>32MB) */
but it doesn't boot.
Any suggestion?
The current code is tested only for 512byte page size NAND devices. Very likely it needs some changes for 2k devices. Especially the ECC stuff will need some changes.
What is CFG_NAND_PAGE_COUNT anyway?
CFG_NAND_PAGE_SIZE defines the number of pages per block. For example a 64MByte NAND chips has a page size of 512 bytes and a block size of 16kbytes. This makes 16k/512 == 32.
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
Hi, Stefan: _____________________________________________________________ On Thursday, December 20, 2007 9:58 PM Stefan Roese wrote:
[Leonid] I am trying to boot 440EPx board similar to Seqouia from
NAND. > > NAND flash is different from Sequoia's though, it has page size
2K, sector size 128K and it's 1Gb (128MB).
[snip]
The current code is tested only for 512byte page size NAND devices.
Very
likely it needs some changes for 2k devices. Especially the ECC stuff
will
need some changes.
[Leonid] You mean 512 bytes block may be hardcoded somewhere instead of using page size definition from <board>.h file? Any suggestions what places in the code look into? ECC stuff - where is it?
[Leonid] What is CFG_NAND_PAGE_COUNT anyway?
CFG_NAND_PAGE_SIZE defines the number of pages per block. For example
a
64MByte NAND chips has a page size of 512 bytes and a block size of 16kbytes. This makes 16k/512 == 32.
[Leonid] OK, that what I thought it is. In my flash with 128K blocks and 2K pages I got page count 128/2=64.
Thanks a lot, Leonid.
Hi Shami,
On Thursday 20 December 2007, shami Allam wrote:
I assigned the ethaddr as 192.168.13.246 and after that i run the command "saveenv " and reset the board.
As Wolfgang already mentioned, this is *not* an ethernet address but an IP address.
I got the following Net: ppc_4xx_eth0. once i get the shell prompt i assign the ipaddr as 192.168.13.241 and after that i run the command "saveenv" and reset the board. Now i tried to ping my Host PC which has the IP address as 192.168.13.240, i am getting the following error.....I am not able to ping the host IP. Can you please show some way to come of this issue..... => ping 192.168.13.240 Trying ppc_4xx_eth0 PHY speed read failed, assuming 10bT PHY duplex read failed, assuming half duplex ENET Speed is 10 Mbps - HALF duplex connection
Did you configure the PHY address correctly? What does "mii info" show? how did you configure the PHY address in your board config file?
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
Thanks for the information. But I read some where that for the Lab testing purpose that I can give the IP address!!!!! I am able to read the PHY inforamtion by command mii info 0x01<PHY Addr>. Following is the info.... => mii info 0x01 PHY_PHYIDR2 @ 0x1 = 0x5c90 PHY_PHYIDR[1,2] @ 0x1 = 0x20005c90 PHY_BMCR value is 0x2100 PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00, 100baseT, FDX => But my Link LED is not glowing at all. Always my Link status shows "Not Active" can anyone throw some light for me..... Regards, Shami...
Stefan Roese sr@denx.de wrote: Hi Shami,
On Thursday 20 December 2007, shami Allam wrote:
I assigned the ethaddr as 192.168.13.246 and after that i run the command "saveenv " and reset the board.
As Wolfgang already mentioned, this is *not* an ethernet address but an IP address.
I got the following Net: ppc_4xx_eth0. once i get the shell prompt i assign the ipaddr as 192.168.13.241 and after that i run the command "saveenv" and reset the board. Now i tried to ping my Host PC which has the IP address as 192.168.13.240, i am getting the following error.....I am not able to ping the host IP. Can you please show some way to come of this issue..... => ping 192.168.13.240 Trying ppc_4xx_eth0 PHY speed read failed, assuming 10bT PHY duplex read failed, assuming half duplex ENET Speed is 10 Mbps - HALF duplex connection
Did you configure the PHY address correctly? What does "mii info" show? how did you configure the PHY address in your board config file?
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
--------------------------------- Now you can chat without downloading messenger. Click here to know how.
On Friday 21 December 2007, shami Allam wrote:
Thanks for the information. But I read some where that for the Lab testing purpose that I can give the IP address!!!!!
Please don't mix up ethernet address (== MAC address) and IP address. Of course you can set ip addresses (and should if you don't use dhcp/bootp). But you have to configure valid ethernet addresses too. If you don't have an ethernet address pool, you can use the "tools/gen_eth_addr" tool to create a random valid eth address for testing.
I am able to read the PHY inforamtion by command mii info 0x01<PHY Addr>. Following is the info.... => mii info 0x01 PHY_PHYIDR2 @ 0x1 = 0x5c90 PHY_PHYIDR[1,2] @ 0x1 = 0x20005c90 PHY_BMCR value is 0x2100 PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00, 100baseT, FDX
And what does "mii info" show (without parameter)?
What is the value of CONFIG_PHY_ADDR in your board config file?
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
--- Stefan Roese sr@denx.de wrote:
On Friday 21 December 2007, shami Allam wrote:
Thanks for the information. But I read some where
that for the Lab testing
purpose that I can give the IP address!!!!!
Please don't mix up ethernet address (== MAC address) and IP address. Of course you can set ip addresses (and should if you don't use dhcp/bootp). But you have to configure valid ethernet addresses too. If you don't have an ethernet address pool, you can use the "tools/gen_eth_addr" tool to create a random valid eth address for testing.
I am able to read the PHY inforamtion by command mii info 0x01<PHY Addr>.
Following is the info....
=> mii info 0x01 PHY_PHYIDR2 @ 0x1 = 0x5c90 PHY_PHYIDR[1,2] @ 0x1 = 0x20005c90 PHY_BMCR value is 0x2100 PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00,
100baseT, FDX
And what does "mii info" show (without parameter)?
PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY_PHYIDR2 @ 0x17 = 0x5c90 PHY_PHYIDR[1,2] @ 0x17 = 0x20005c90 PHY_BMCR value is 0x2100 PHY 0x17: OUI = 0x80017, Model = 0x09, Rev = 0x00, 100baseT, FDX PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed =>
What is the value of CONFIG_PHY_ADDR in your board config file?
#define CONFIG_PHY_ADDR 1/* PHY address*/
Best regards,
Regards, Shami.
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
=====================================================================
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
U-Boot-Users mailing list U-Boot-Users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users
Download prohibited? No problem. CHAT from any browser, without download. Go to http://in.messenger.yahoo.com/webmessengerpromo.php/
Save all your chat conversations. Find them online at http://in.messenger.yahoo.com/webmessengerpromo.php
Hey Shami, I help you to see the mail on 4xx, but don't send mails from my id. No more access my Id. ok
Regards, Raj.
--- raj ubootimage@yahoo.co.in wrote:
--- Stefan Roese sr@denx.de wrote:
On Friday 21 December 2007, shami Allam wrote:
Thanks for the information. But I read some
where
that for the Lab testing
purpose that I can give the IP address!!!!!
Please don't mix up ethernet address (== MAC address) and IP address. Of course you can set ip addresses (and should if you don't use dhcp/bootp). But you have to configure valid ethernet addresses
too.
If you don't have an ethernet address pool, you can use the "tools/gen_eth_addr" tool to create a random valid eth address for testing.
I am able to read the PHY inforamtion by command mii info 0x01<PHY Addr>.
Following is the info....
=> mii info 0x01 PHY_PHYIDR2 @ 0x1 = 0x5c90 PHY_PHYIDR[1,2] @ 0x1 = 0x20005c90 PHY_BMCR value is 0x2100 PHY 0x01: OUI = 0x80017, Model = 0x09, Rev =
0x00,
100baseT, FDX
And what does "mii info" show (without parameter)?
PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY_PHYIDR2 @ 0x17 = 0x5c90 PHY_PHYIDR[1,2] @ 0x17 = 0x20005c90 PHY_BMCR value is 0x2100 PHY 0x17: OUI = 0x80017, Model = 0x09, Rev = 0x00, 100baseT, FDX PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed =>
What is the value of CONFIG_PHY_ADDR in your board config file?
#define CONFIG_PHY_ADDR 1/* PHY address*/
Best regards,
Regards, Shami.
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de
=====================================================================
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
U-Boot-Users mailing list U-Boot-Users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users
Download prohibited? No problem. CHAT from anybrowser, without download. Go to http://in.messenger.yahoo.com/webmessengerpromo.php/
Save all your chat conversations. Find themonline at http://in.messenger.yahoo.com/webmessengerpromo.php
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
U-Boot-Users mailing list U-Boot-Users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users
Did you know? You can CHAT without downloading messenger. Go to http://in.messenger.yahoo.com/webmessengerpromo.php/
Sorry Raj.... I am sending from my id....
Stefan Roese sr@denx.de wrote: On Friday 21 December 2007, shami Allam wrote:
Thanks for the information. But I read some where that for the Lab testing purpose that I can give the IP address!!!!!
Please don't mix up ethernet address (== MAC address) and IP address. Of course you can set ip addresses (and should if you don't use dhcp/bootp). But you have to configure valid ethernet addresses too. If you don't have an ethernet address pool, you can use the "tools/gen_eth_addr" tool to create a random valid eth address for testing.
I am able to read the PHY inforamtion by command mii info 0x01
.. Following is the info....
=> mii info 0x01 PHY_PHYIDR2 @ 0x1 = 0x5c90 PHY_PHYIDR[1,2] @ 0x1 = 0x20005c90 PHY_BMCR value is 0x2100 PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00, 100baseT, FDX
And what does "mii info" show (without parameter)?
=> mii info PHY ID register 2 read failed PHY_PHYIDR2 @ 0x1 = 0x5c90 PHY_PHYIDR[1,2] @ 0x1 = 0x20005c90 PHY_BMCR value is 0x2100 PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00, 100baseT, PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed PHY ID register 2 read failed like this many....
What is the value of CONFIG_PHY_ADDR in your board config file?
follwing i defined in the board config file.....
#define CONFIG_PHY_ADDR 1
Regards, Shami.... Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
--------------------------------- Why delete messages? Unlimited storage is just a click away.
Hi Stefan,
After booting my target i get the following message..
I2C:ready DRAM:16MB FLASH:2MB In: serial Out:serial Err:serial Net: ppc_4xx_eth0 => and after that if i say => mii info PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00, 10baseT, HDX => setenv ipaddr 192.168.13.248 => ping 192.168.13.248 After this if i ping it's not pinging self and also the host ip(192.168.13.240). Can you help me out what could be the problem..... => mii read 0x01<PHY Addr> 0x01<register val> when i read the PHY 0x01 register following is the value 0x7849. This value show that "No Link". why so. PHY chip i am using DP83848I
Regards, Shami.
Stefan Roese sr@denx.de wrote: On Wednesday 19 December 2007, shami Allam wrote:
I am working on the 405GP custome board. I am able to bringup the SDRAM,Flash,I2c and serail on the board. But while trying to bringup the ethernet i am getting the following error. "No Ethernet found". On my board there is "DP83848I" PHY chip.
This message gets printed when you don't define the "ethaddr" environement address. So set this variable to a valid value and save the environment and reset the board. Then you should see one eth-interface.
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
--------------------------------- Now you can chat without downloading messenger. Click here to know how.
--------------------------------- Save all your chat conversations. Find them online.
On Saturday 22 December 2007, shami Allam wrote:
After booting my target i get the following message..
I2C:ready DRAM:16MB FLASH:2MB In: serial Out:serial Err:serial Net: ppc_4xx_eth0 => and after that if i say => mii info PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00, 10baseT, HDX
And is this correct? Do you have a 10MBit connection?
=> setenv ipaddr 192.168.13.248 => ping 192.168.13.248
So you try to ping to yourself here. This does not work. You have to ping to a different target (PC).
After this if i ping it's not pinging self and also the host ip(192.168.13.240). Can you help me out what could be the problem..... => mii read 0x01<PHY Addr> 0x01<register val> when i read the PHY 0x01 register following is the value 0x7849. This value show that "No Link". why so. PHY chip i am using DP83848I
Possibly a PHY configuartion problem. Did you check if you soldered the correct resistors and condensators? Is the power-supply ok?
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
On Saturday 22 December 2007, shami Allam wrote:
After booting my target i get the following message..
I2C:ready DRAM:16MB FLASH:2MB In: serial Out:serial Err:serial Net: ppc_4xx_eth0 => and after that if i say => mii info PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00, 10baseT, HDX
And is this correct? Do you have a 10MBit connection?
it support both 100baseT and 10baseT.
=> setenv ipaddr 192.168.13.248 => ping 192.168.13.248
So you try to ping to yourself here. This does not work. You have to ping to a different target (PC).
Yes i tried to ping the Host PC (i.e) 192.168.13.240. But still i am not getting reply.....
After this if i ping it's not pinging self and also the host ip(192.168.13.240). Can you help me out what could be the problem..... => mii read 0x01
0x01
when i read the PHY 0x01 register following is the value 0x7849. This value show that "No Link". why so. PHY chip i am using DP83848I
Possibly a PHY configuartion problem. Did you check if you soldered the correct resistors and condensators? Is the power-supply ok?
if I do the PHY loopback by enabling the bit 14bit in the BMCR. i am getting the reply. Still you suspect PHY configuration problem.....or do i need to do anything at MAC side......
Regards, Shami.
--------------------------------- Download prohibited? No problem. CHAT from any browser, without download.
On Saturday 22 December 2007, shami Allam wrote:
After this if i ping it's not pinging self and also the host ip(192.168.13.240). Can you help me out what could be the problem..... => mii read 0x01
0x01
when i read the PHY 0x01 register following is the value 0x7849. This value show that "No Link". why so. PHY chip i am using DP83848I
Possibly a PHY configuartion problem. Did you check if you soldered the correct resistors and condensators? Is the power-supply ok?
if I do the PHY loopback by enabling the bit 14bit in the BMCR. i am getting the reply. Still you suspect PHY configuration problem.....or do i need to do anything at MAC side......
Yes, I still suspect PHY hardware problems. Check (again) all R's and C's, clocks and power supplies.
Best regards, Stefan
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
participants (5)
-
Leonid -
raj -
shami Allam -
Stefan Roese -
Wolfgang Denk