[PATCH v2] rockchip: rk3568: Add support for Lubancat2 board from EmbedFire
LubanCat2 is a rk3568 based SBC from EmbedFire.
Specification: - Rockchip rk3568 - LPDDR4/4X 1/2/4/8 GB - TF scard slot - eMMC 8/32/64/128 GB - Gigabit ethernet x 2 - HDMI out - USB 2.0 Host x 1 - USB 2.0 Type-C OTG x 1 - USB 3.0 Host x 1 - Mini PCIE interface for WIFI/BT module - M.2 key for 2280 NVME - 40 pin header
The dts file is sync from linux mainline.
Signed-off-by: Andy Yan andyshrk@163.com
---
Changes in v2: - enable SPL_FIT_SIGNATURE
arch/arm/dts/Makefile | 3 +- arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi | 87 +++ arch/arm/dts/rk3568-lubancat-2.dts | 734 +++++++++++++++++++++ configs/lubancat-2-rk3568_defconfig | 94 +++ 4 files changed, 917 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3568-lubancat-2.dts create mode 100644 configs/lubancat-2-rk3568_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 480269fa60..b177c0c4f9 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -169,7 +169,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \ rk3566-anbernic-rgxx3.dtb \ rk3566-radxa-cm3-io.dtb \ rk3568-evb.dtb \ - rk3568-rock-3a.dtb + rk3568-rock-3a.dtb \ + rk3568-lubancat-2.dtb
dtb-$(CONFIG_ROCKCHIP_RK3588) += \ rk3588-edgeble-neu6a-io.dtb \ diff --git a/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi b/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi new file mode 100644 index 0000000000..42072dd0bd --- /dev/null +++ b/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2023 Rockchip Electronics Co., Ltd + * (C) Copyright 2023 Andy Yan andyshrk@163.com + */ + +#include "rk356x-u-boot.dtsi" + +/ { + chosen { + stdout-path = &uart2; + }; +}; + +&emmc_bus8 { + bootph-all; +}; + +&emmc_clk { + bootph-all; +}; + +&emmc_cmd { + bootph-all; +}; + +&emmc_datastrobe { + bootph-all; +}; + +&pinctrl { + bootph-all; +}; + +&pcfg_pull_none { + bootph-all; +}; + +&pcfg_pull_up_drv_level_2 { + bootph-all; +}; + +&pcfg_pull_up { + bootph-all; +}; + +&sdmmc0_bus4 { + bootph-all; +}; + +&sdmmc0_clk { + bootph-all; +}; + +&sdmmc0_cmd { + bootph-all; +}; + +&sdmmc0_det { + bootph-all; +}; + +&sdhci { + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; +}; + +&sdmmc2 { + status = "disabled"; +}; + +&uart1 { + status = "disabled"; +}; + +&uart2m0_xfer { + bootph-all; +}; + +&uart2 { + clock-frequency = <24000000>; + bootph-all; + status = "okay"; +}; diff --git a/arch/arm/dts/rk3568-lubancat-2.dts b/arch/arm/dts/rk3568-lubancat-2.dts new file mode 100644 index 0000000000..da257b0591 --- /dev/null +++ b/arch/arm/dts/rk3568-lubancat-2.dts @@ -0,0 +1,734 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/* + * Copyright (c) 2023 Rockchip Electronics Co., Ltd. + * Copyright (c) 2023 EmbedFire embedfire@embedfire.com + * Copyright (c) 2023 Andy Yan andyshrk@163.com + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/soc/rockchip,vop2.h> +#include "rk3568.dtsi" + +/ { + model = "EmbedFire LubanCat 2"; + compatible = "embedfire,lubancat-2", "rockchip,rk3568"; + + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + mmc0 = &sdmmc0; + mmc1 = &sdhci; + }; + + chosen: chosen { + stdout-path = "serial2:1500000n8"; + }; + + leds { + compatible = "gpio-leds"; + + user_led: user-led { + label = "user_led"; + linux,default-trigger = "heartbeat"; + default-state = "on"; + gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&user_led_pin>; + }; + }; + + hdmi-con { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + dc_5v: dc-5v-regulator { + compatible = "regulator-fixed"; + regulator-name = "dc_5v"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + vcc3v3_sys: vcc3v3-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&dc_5v>; + }; + + vcc3v3_m2_pcie: vcc3v3-m2-pcie-regulator { + compatible = "regulator-fixed"; + regulator-name = "m2_pcie_3v3"; + enable-active-high; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc3v3_m2_pcie_en>; + pinctrl-names = "default"; + startup-delay-us = <200000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc3v3_mini_pcie: vcc3v3-mini-pcie-regulator { + compatible = "regulator-fixed"; + regulator-name = "minipcie_3v3"; + enable-active-high; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc3v3_mini_pcie_en>; + pinctrl-names = "default"; + startup-delay-us = <5000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc5v0_usb20_host: vcc5v0-usb20-host-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_usb20_host"; + enable-active-high; + gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc5v0_usb20_host_en>; + pinctrl-names = "default"; + }; + + vcc5v0_usb30_host: vcc5v0-usb30-host-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_usb30_host"; + enable-active-high; + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc5v0_usb30_host_en>; + pinctrl-names = "default"; + }; + + vcc5v0_otg_vbus: vcc5v0-otg-vbus-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_otg_vbus"; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc5v0_otg_vbus_en>; + pinctrl-names = "default"; + }; +}; + +&combphy0 { + status = "okay"; +}; + +&combphy1 { + status = "okay"; +}; + +&combphy2 { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu1 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu2 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu3 { + cpu-supply = <&vdd_cpu>; +}; + +&gpu { + mali-supply = <&vdd_gpu>; + status = "okay"; +}; + +&hdmi { + avdd-0v9-supply = <&vdda0v9_image>; + avdd-1v8-supply = <&vcca1v8_image>; + status = "okay"; +}; + +&hdmi_in { + hdmi_in_vp0: endpoint { + remote-endpoint = <&vp0_out_hdmi>; + }; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&hdmi_sound { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + vdd_cpu: regulator@1c { + compatible = "tcs,tcs4525"; + reg = <0x1c>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc5v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + rk809: pmic@20 { + compatible = "rockchip,rk809"; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>; + assigned-clocks = <&cru I2S1_MCLKOUT_TX>; + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>; + #clock-cells = <1>; + clock-names = "mclk"; + clocks = <&cru I2S1_MCLKOUT_TX>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + rockchip,system-power-controller; + #sound-dai-cells = <0>; + vcc1-supply = <&vcc3v3_sys>; + vcc2-supply = <&vcc3v3_sys>; + vcc3-supply = <&vcc3v3_sys>; + vcc4-supply = <&vcc3v3_sys>; + vcc5-supply = <&vcc3v3_sys>; + vcc6-supply = <&vcc3v3_sys>; + vcc7-supply = <&vcc3v3_sys>; + vcc8-supply = <&vcc3v3_sys>; + vcc9-supply = <&vcc3v3_sys>; + wakeup-source; + + regulators { + vdd_logic: DCDC_REG1 { + regulator-name = "vdd_logic"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-name = "vdd_gpu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vdd_npu: DCDC_REG4 { + regulator-name = "vdd_npu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8: DCDC_REG5 { + regulator-name = "vcc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_image: LDO_REG1 { + regulator-name = "vdda0v9_image"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda_0v9: LDO_REG2 { + regulator-name = "vdda_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_pmu: LDO_REG3 { + regulator-name = "vdda0v9_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vccio_acodec: LDO_REG4 { + regulator-name = "vccio_acodec"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-name = "vccio_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_pmu: LDO_REG6 { + regulator-name = "vcc3v3_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcca_1v8: LDO_REG7 { + regulator-name = "vcca_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca1v8_pmu: LDO_REG8 { + regulator-name = "vcca1v8_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcca1v8_image: LDO_REG9 { + regulator-name = "vcca1v8_image"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_3v3: SWITCH_REG1 { + regulator-name = "vcc_3v3"; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_sd: SWITCH_REG2 { + regulator-name = "vcc3v3_sd"; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&i2s1_8ch { + rockchip,trcm-sync-tx-only; + status = "okay"; +}; + +&gmac0 { + phy-mode = "rgmii"; + clock_in_out = "output"; + + snps,reset-gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + /* Reset time is 20ms, 100ms for rtl8211f */ + snps,reset-delays-us = <0 20000 100000>; + + assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>; + assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>; + + pinctrl-names = "default"; + pinctrl-0 = <&gmac0_miim + &gmac0_tx_bus2 + &gmac0_rx_bus2 + &gmac0_rgmii_clk + &gmac0_rgmii_bus>; + + tx_delay = <0x22>; + rx_delay = <0x0e>; + + phy-handle = <&rgmii_phy0>; + status = "okay"; +}; + +&mdio0 { + rgmii_phy0: phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + }; +}; + +&gmac1 { + phy-mode = "rgmii"; + clock_in_out = "output"; + + snps,reset-gpio = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + /* Reset time is 20ms, 100ms for rtl8211f */ + snps,reset-delays-us = <0 20000 100000>; + + assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>; + assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>; + + pinctrl-names = "default"; + pinctrl-0 = <&gmac1m1_miim + &gmac1m1_tx_bus2 + &gmac1m1_rx_bus2 + &gmac1m1_rgmii_clk + &gmac1m1_rgmii_bus>; + + tx_delay = <0x21>; + rx_delay = <0x0e>; + + phy-handle = <&rgmii_phy1>; + status = "okay"; +}; + +&mdio1 { + rgmii_phy1: phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + }; +}; + +&gic { + mbi-ranges = <94 31>, <229 31>, <289 31>; +}; + +&pcie30phy { + status = "okay"; +}; + +&pcie3x2 { + reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_m2_pcie>; + status = "okay"; +}; + +&pcie2x1 { + reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>; + disable-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_mini_pcie>; + status = "okay"; +}; + +&pmu_io_domains { + pmuio2-supply = <&vcc3v3_pmu>; + vccio1-supply = <&vccio_acodec>; + vccio3-supply = <&vccio_sd>; + vccio4-supply = <&vcc_1v8>; + vccio5-supply = <&vcc_3v3>; + vccio6-supply = <&vcc_1v8>; + vccio7-supply = <&vcc_3v3>; + status = "okay"; +}; + +&pwm8 { + status = "okay"; +}; + +&pwm9 { + status = "disabled"; +}; + +&pwm10 { + status = "disabled"; +}; + +&pwm14 { + status = "disabled"; +}; + +&spi3 { + pinctrl-0 = <&spi3m1_pins>; + status = "disabled"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3m1_xfer>; + status = "disabled"; +}; + +&saradc { + vref-supply = <&vcca_1v8>; + status = "okay"; +}; + +&tsadc { + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <0>; + status = "okay"; +}; + +&sdhci { + assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>, <&cru CCLK_EMMC>; + assigned-clock-rates = <200000000>, <24000000>, <200000000>; + bus-width = <8>; + max-frequency = <200000000>; + mmc-hs200-1_8v; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>; + supports-emmc; + status = "okay"; +}; + +&sdmmc0 { + max-frequency = <150000000>; + no-sdio; + no-mmc; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + disable-wp; + sd-uhs-sdr104; + vmmc-supply = <&vcc3v3_sd>; + vqmmc-supply = <&vccio_sd>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>; + status = "okay"; +}; + +/* USB OTG/USB Host_1 USB 2.0 Comb */ +&usb2phy0 { + status = "okay"; +}; + +&usb2phy0_host { + phy-supply = <&vcc5v0_usb30_host>; + status = "okay"; +}; + +&usb2phy0_otg { + phy-supply = <&vcc5v0_otg_vbus>; + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host0_ohci { + status = "okay"; +}; + +/* USB Host_2/USB Host_3 USB 2.0 Comb */ +&usb2phy1 { + status = "okay"; +}; + +&usb2phy1_host { + status = "okay"; +}; + +&usb2phy1_otg { + phy-supply = <&vcc5v0_usb20_host>; + status = "okay"; +}; + +&usb_host1_ehci { + status = "okay"; +}; + +&usb_host1_ohci { + status = "okay"; +}; + +/* MULTI_PHY0 For SATA0, USB3.0 OTG Only USB2.0 */ +&usb_host0_xhci { + phys = <&usb2phy0_otg>; + phy-names = "usb2-phy"; + extcon = <&usb2phy0>; + maximum-speed = "high-speed"; + dr_mode = "host"; + status = "okay"; +}; + +&sata0 { + status = "okay"; +}; + +/* USB3.0 Host */ +&usb_host1_xhci { + status = "okay"; +}; + +&vop { + assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>; + assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>; + status = "okay"; +}; + +&vop_mmu { + status = "okay"; +}; + +&vp0 { + vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 { + reg = <ROCKCHIP_VOP2_EP_HDMI0>; + remote-endpoint = <&hdmi_in_vp0>; + }; +}; + +&pinctrl { + leds { + user_led_pin: user-status-led-pin { + rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb { + vcc5v0_usb20_host_en: vcc5v0-usb20-host-en { + rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc5v0_usb30_host_en: vcc5v0-usb30-host-en { + rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc5v0_otg_vbus_en: vcc5v0-otg-vbus-en { + rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pcie { + vcc3v3_m2_pcie_en: vcc3v3-m2-pcie-en { + rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc3v3_mini_pcie_en: vcc3v3-mini-pcie-en { + rockchip,pins = <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + pmic_int: pmic-int { + rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; diff --git a/configs/lubancat-2-rk3568_defconfig b/configs/lubancat-2-rk3568_defconfig new file mode 100644 index 0000000000..40ac1dda4f --- /dev/null +++ b/configs/lubancat-2-rk3568_defconfig @@ -0,0 +1,94 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_TEXT_BASE=0x00a00000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_SF_DEFAULT_MODE=0x2000 +CONFIG_DEFAULT_DEVICE_TREE="rk3568-lubancat-2" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_ROCKCHIP_SPI_IMAGE=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_SPL_STACK=0x400000 +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-lubancat-2.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x4000000 +CONFIG_SPL_BSS_MAX_SIZE=0x4000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_SPL_CLK=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_XTX=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_ROCKCHIP_SFC=y +CONFIG_SYSRESET=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_ERRNO_STR=y
Hi Andy, On 2023-07-08 12:25, Andy Yan wrote:
LubanCat2 is a rk3568 based SBC from EmbedFire.
Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header
The dts file is sync from linux mainline.
Signed-off-by: Andy Yan andyshrk@163.com
Changes in v2:
- enable SPL_FIT_SIGNATURE
arch/arm/dts/Makefile | 3 +- arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi | 87 +++ arch/arm/dts/rk3568-lubancat-2.dts | 734 +++++++++++++++++++++ configs/lubancat-2-rk3568_defconfig | 94 +++ 4 files changed, 917 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3568-lubancat-2.dts create mode 100644 configs/lubancat-2-rk3568_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 480269fa60..b177c0c4f9 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -169,7 +169,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \ rk3566-anbernic-rgxx3.dtb \ rk3566-radxa-cm3-io.dtb \ rk3568-evb.dtb \
- rk3568-rock-3a.dtb
- rk3568-rock-3a.dtb \
- rk3568-lubancat-2.dtb
Your file should be added in alphabetical order, after rk3568-evb.dtb.
dtb-$(CONFIG_ROCKCHIP_RK3588) += \ rk3588-edgeble-neu6a-io.dtb \ diff --git a/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi b/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi new file mode 100644 index 0000000000..42072dd0bd --- /dev/null +++ b/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: GPL-2.0+ +/*
- (C) Copyright 2023 Rockchip Electronics Co., Ltd
- (C) Copyright 2023 Andy Yan andyshrk@163.com
- */
+#include "rk356x-u-boot.dtsi"
+/ {
- chosen {
stdout-path = &uart2;- };
+};
+&emmc_bus8 {
- bootph-all;
+};
+&emmc_clk {
- bootph-all;
+};
+&emmc_cmd {
- bootph-all;
+};
+&emmc_datastrobe {
- bootph-all;
+};
+&pinctrl {
- bootph-all;
+};
+&pcfg_pull_none {
- bootph-all;
+};
+&pcfg_pull_up_drv_level_2 {
- bootph-all;
+};
+&pcfg_pull_up {
- bootph-all;
+};
+&sdmmc0_bus4 {
- bootph-all;
+};
+&sdmmc0_clk {
- bootph-all;
+};
+&sdmmc0_cmd {
- bootph-all;
+};
+&sdmmc0_det {
- bootph-all;
+};
After the "rockchip: rk3568: Device Tree updates" series all pinctrl related nodes above can be removed.
+&sdhci {
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- mmc-hs400-1_8v;
- mmc-hs400-enhanced-strobe;
Board dts is missing the emmc_datastrobe pinconfig and should be fixed here when hs200/hs400 mode support is flagged here.
+};
+&sdmmc2 {
- status = "disabled";
+};
+&uart1 {
- status = "disabled";
+};
These two nodes is not enabled in board dts and can be removed.
+&uart2m0_xfer {
- bootph-all;
+};
Se pinctrl related comment above.
+&uart2 {
- clock-frequency = <24000000>;
- bootph-all;
Props is preferred to be in alphabetical order.
- status = "okay";
+}; diff --git a/arch/arm/dts/rk3568-lubancat-2.dts b/arch/arm/dts/rk3568-lubancat-2.dts new file mode 100644 index 0000000000..da257b0591 --- /dev/null +++ b/arch/arm/dts/rk3568-lubancat-2.dts @@ -0,0 +1,734 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
- Copyright (c) 2023 Rockchip Electronics Co., Ltd.
- Copyright (c) 2023 EmbedFire embedfire@embedfire.com
- Copyright (c) 2023 Andy Yan andyshrk@163.com
- */
+/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/soc/rockchip,vop2.h> +#include "rk3568.dtsi"
+/ {
- model = "EmbedFire LubanCat 2";
- compatible = "embedfire,lubancat-2", "rockchip,rk3568";
- aliases {
ethernet0 = &gmac0;ethernet1 = &gmac1;mmc0 = &sdmmc0;mmc1 = &sdhci;- };
- chosen: chosen {
stdout-path = "serial2:1500000n8";- };
- leds {
compatible = "gpio-leds";user_led: user-led {label = "user_led";linux,default-trigger = "heartbeat";default-state = "on";gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>;pinctrl-names = "default";pinctrl-0 = <&user_led_pin>;};- };
- hdmi-con {
compatible = "hdmi-connector";type = "a";port {hdmi_con_in: endpoint {remote-endpoint = <&hdmi_out_con>;};};- };
- dc_5v: dc-5v-regulator {
compatible = "regulator-fixed";regulator-name = "dc_5v";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;- };
- vcc3v3_sys: vcc3v3-sys-regulator {
compatible = "regulator-fixed";regulator-name = "vcc3v3_sys";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;vin-supply = <&vcc5v0_sys>;- };
- vcc5v0_sys: vcc5v0-sys-regulator {
compatible = "regulator-fixed";regulator-name = "vcc5v0_sys";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;vin-supply = <&dc_5v>;- };
- vcc3v3_m2_pcie: vcc3v3-m2-pcie-regulator {
compatible = "regulator-fixed";regulator-name = "m2_pcie_3v3";enable-active-high;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;pinctrl-0 = <&vcc3v3_m2_pcie_en>;pinctrl-names = "default";startup-delay-us = <200000>;vin-supply = <&vcc5v0_sys>;- };
- vcc3v3_mini_pcie: vcc3v3-mini-pcie-regulator {
compatible = "regulator-fixed";regulator-name = "minipcie_3v3";enable-active-high;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;gpio = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>;pinctrl-0 = <&vcc3v3_mini_pcie_en>;pinctrl-names = "default";startup-delay-us = <5000>;vin-supply = <&vcc5v0_sys>;- };
- vcc5v0_usb20_host: vcc5v0-usb20-host-regulator {
compatible = "regulator-fixed";regulator-name = "vcc5v0_usb20_host";enable-active-high;gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;pinctrl-0 = <&vcc5v0_usb20_host_en>;pinctrl-names = "default";- };
- vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
compatible = "regulator-fixed";regulator-name = "vcc5v0_usb30_host";enable-active-high;gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;pinctrl-0 = <&vcc5v0_usb30_host_en>;pinctrl-names = "default";- };
- vcc5v0_otg_vbus: vcc5v0-otg-vbus-regulator {
compatible = "regulator-fixed";regulator-name = "vcc5v0_otg_vbus";enable-active-high;regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;pinctrl-0 = <&vcc5v0_otg_vbus_en>;pinctrl-names = "default";- };
+};
+&combphy0 {
- status = "okay";
+};
+&combphy1 {
- status = "okay";
+};
+&combphy2 {
- status = "okay";
+};
+&cpu0 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu1 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu2 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu3 {
- cpu-supply = <&vdd_cpu>;
+};
+&gpu {
- mali-supply = <&vdd_gpu>;
- status = "okay";
+};
+&hdmi {
- avdd-0v9-supply = <&vdda0v9_image>;
- avdd-1v8-supply = <&vcca1v8_image>;
- status = "okay";
+};
+&hdmi_in {
- hdmi_in_vp0: endpoint {
remote-endpoint = <&vp0_out_hdmi>;- };
+};
+&hdmi_out {
- hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;- };
+};
+&hdmi_sound {
- status = "okay";
+};
+&i2c0 {
- status = "okay";
- vdd_cpu: regulator@1c {
compatible = "tcs,tcs4525";reg = <0x1c>;fcs,suspend-voltage-selector = <1>;regulator-name = "vdd_cpu";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <800000>;regulator-max-microvolt = <1150000>;regulator-ramp-delay = <2300>;vin-supply = <&vcc5v0_sys>;regulator-state-mem {regulator-off-in-suspend;};- };
- rk809: pmic@20 {
compatible = "rockchip,rk809";reg = <0x20>;interrupt-parent = <&gpio0>;interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;assigned-clocks = <&cru I2S1_MCLKOUT_TX>;assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;#clock-cells = <1>;clock-names = "mclk";clocks = <&cru I2S1_MCLKOUT_TX>;pinctrl-names = "default";pinctrl-0 = <&pmic_int>;rockchip,system-power-controller;#sound-dai-cells = <0>;vcc1-supply = <&vcc3v3_sys>;vcc2-supply = <&vcc3v3_sys>;vcc3-supply = <&vcc3v3_sys>;vcc4-supply = <&vcc3v3_sys>;vcc5-supply = <&vcc3v3_sys>;vcc6-supply = <&vcc3v3_sys>;vcc7-supply = <&vcc3v3_sys>;vcc8-supply = <&vcc3v3_sys>;vcc9-supply = <&vcc3v3_sys>;wakeup-source;regulators {vdd_logic: DCDC_REG1 {regulator-name = "vdd_logic";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <500000>;regulator-max-microvolt = <1350000>;regulator-init-microvolt = <900000>;regulator-ramp-delay = <6001>;regulator-initial-mode = <0x2>;regulator-state-mem {regulator-off-in-suspend;};};vdd_gpu: DCDC_REG2 {regulator-name = "vdd_gpu";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <500000>;regulator-max-microvolt = <1350000>;regulator-init-microvolt = <900000>;regulator-ramp-delay = <6001>;regulator-initial-mode = <0x2>;regulator-state-mem {regulator-off-in-suspend;};};vcc_ddr: DCDC_REG3 {regulator-name = "vcc_ddr";regulator-always-on;regulator-boot-on;regulator-initial-mode = <0x2>;regulator-state-mem {regulator-on-in-suspend;};};vdd_npu: DCDC_REG4 {regulator-name = "vdd_npu";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <500000>;regulator-max-microvolt = <1350000>;regulator-init-microvolt = <900000>;regulator-ramp-delay = <6001>;regulator-initial-mode = <0x2>;regulator-state-mem {regulator-off-in-suspend;};};vcc_1v8: DCDC_REG5 {regulator-name = "vcc_1v8";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-state-mem {regulator-off-in-suspend;};};vdda0v9_image: LDO_REG1 {regulator-name = "vdda0v9_image";regulator-boot-on;regulator-always-on;regulator-min-microvolt = <900000>;regulator-max-microvolt = <900000>;regulator-state-mem {regulator-off-in-suspend;};};vdda_0v9: LDO_REG2 {regulator-name = "vdda_0v9";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <900000>;regulator-max-microvolt = <900000>;regulator-state-mem {regulator-off-in-suspend;};};vdda0v9_pmu: LDO_REG3 {regulator-name = "vdda0v9_pmu";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <900000>;regulator-max-microvolt = <900000>;regulator-state-mem {regulator-on-in-suspend;regulator-suspend-microvolt = <900000>;};};vccio_acodec: LDO_REG4 {regulator-name = "vccio_acodec";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;regulator-state-mem {regulator-off-in-suspend;};};vccio_sd: LDO_REG5 {regulator-name = "vccio_sd";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <3300000>;regulator-state-mem {regulator-off-in-suspend;};};vcc3v3_pmu: LDO_REG6 {regulator-name = "vcc3v3_pmu";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;regulator-state-mem {regulator-on-in-suspend;regulator-suspend-microvolt = <3300000>;};};vcca_1v8: LDO_REG7 {regulator-name = "vcca_1v8";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-state-mem {regulator-off-in-suspend;};};vcca1v8_pmu: LDO_REG8 {regulator-name = "vcca1v8_pmu";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-state-mem {regulator-on-in-suspend;regulator-suspend-microvolt = <1800000>;};};vcca1v8_image: LDO_REG9 {regulator-name = "vcca1v8_image";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-state-mem {regulator-off-in-suspend;};};vcc_3v3: SWITCH_REG1 {regulator-name = "vcc_3v3";regulator-always-on;regulator-boot-on;regulator-state-mem {regulator-off-in-suspend;};};vcc3v3_sd: SWITCH_REG2 {regulator-name = "vcc3v3_sd";regulator-always-on;regulator-boot-on;regulator-state-mem {regulator-off-in-suspend;};};};- };
+};
+&i2s1_8ch {
- rockchip,trcm-sync-tx-only;
- status = "okay";
+};
+&gmac0 {
- phy-mode = "rgmii";
- clock_in_out = "output";
- snps,reset-gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
- snps,reset-active-low;
- /* Reset time is 20ms, 100ms for rtl8211f */
- snps,reset-delays-us = <0 20000 100000>;
- assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
- assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
- pinctrl-names = "default";
- pinctrl-0 = <&gmac0_miim
&gmac0_tx_bus2&gmac0_rx_bus2&gmac0_rgmii_clk&gmac0_rgmii_bus>;- tx_delay = <0x22>;
- rx_delay = <0x0e>;
- phy-handle = <&rgmii_phy0>;
- status = "okay";
+};
+&mdio0 {
- rgmii_phy0: phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";reg = <0x0>;- };
+};
+&gmac1 {
- phy-mode = "rgmii";
- clock_in_out = "output";
- snps,reset-gpio = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
- snps,reset-active-low;
- /* Reset time is 20ms, 100ms for rtl8211f */
- snps,reset-delays-us = <0 20000 100000>;
- assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
- assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
- pinctrl-names = "default";
- pinctrl-0 = <&gmac1m1_miim
&gmac1m1_tx_bus2&gmac1m1_rx_bus2&gmac1m1_rgmii_clk&gmac1m1_rgmii_bus>;- tx_delay = <0x21>;
- rx_delay = <0x0e>;
- phy-handle = <&rgmii_phy1>;
- status = "okay";
+};
+&mdio1 {
- rgmii_phy1: phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";reg = <0x0>;- };
+};
+&gic {
- mbi-ranges = <94 31>, <229 31>, <289 31>;
+};
+&pcie30phy {
- status = "okay";
+};
+&pcie3x2 {
- reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
- vpcie3v3-supply = <&vcc3v3_m2_pcie>;
- status = "okay";
+};
+&pcie2x1 {
- reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
- disable-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_HIGH>;
- vpcie3v3-supply = <&vcc3v3_mini_pcie>;
- status = "okay";
+};
+&pmu_io_domains {
- pmuio2-supply = <&vcc3v3_pmu>;
- vccio1-supply = <&vccio_acodec>;
- vccio3-supply = <&vccio_sd>;
- vccio4-supply = <&vcc_1v8>;
- vccio5-supply = <&vcc_3v3>;
- vccio6-supply = <&vcc_1v8>;
- vccio7-supply = <&vcc_3v3>;
- status = "okay";
+};
+&pwm8 {
- status = "okay";
+};
+&pwm9 {
- status = "disabled";
+};
+&pwm10 {
- status = "disabled";
+};
+&pwm14 {
- status = "disabled";
+};
+&spi3 {
- pinctrl-0 = <&spi3m1_pins>;
- status = "disabled";
+};
+&uart2 {
- status = "okay";
+};
+&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart3m1_xfer>;
- status = "disabled";
+};
+&saradc {
- vref-supply = <&vcca_1v8>;
- status = "okay";
+};
+&tsadc {
- rockchip,hw-tshut-mode = <1>;
- rockchip,hw-tshut-polarity = <0>;
- status = "okay";
+};
+&sdhci {
- assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>, <&cru CCLK_EMMC>;
- assigned-clock-rates = <200000000>, <24000000>, <200000000>;
- bus-width = <8>;
- max-frequency = <200000000>;
- mmc-hs200-1_8v;
- non-removable;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
- supports-emmc;
- status = "okay";
+};
+&sdmmc0 {
- max-frequency = <150000000>;
- no-sdio;
- no-mmc;
- bus-width = <4>;
- cap-mmc-highspeed;
- cap-sd-highspeed;
- disable-wp;
- sd-uhs-sdr104;
- vmmc-supply = <&vcc3v3_sd>;
- vqmmc-supply = <&vccio_sd>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
- status = "okay";
+};
+/* USB OTG/USB Host_1 USB 2.0 Comb */ +&usb2phy0 {
- status = "okay";
+};
+&usb2phy0_host {
- phy-supply = <&vcc5v0_usb30_host>;
- status = "okay";
+};
+&usb2phy0_otg {
- phy-supply = <&vcc5v0_otg_vbus>;
- status = "okay";
+};
+&usb_host0_ehci {
- status = "okay";
+};
+&usb_host0_ohci {
- status = "okay";
+};
+/* USB Host_2/USB Host_3 USB 2.0 Comb */ +&usb2phy1 {
- status = "okay";
+};
+&usb2phy1_host {
- status = "okay";
+};
+&usb2phy1_otg {
- phy-supply = <&vcc5v0_usb20_host>;
- status = "okay";
+};
+&usb_host1_ehci {
- status = "okay";
+};
+&usb_host1_ohci {
- status = "okay";
+};
+/* MULTI_PHY0 For SATA0, USB3.0 OTG Only USB2.0 */ +&usb_host0_xhci {
- phys = <&usb2phy0_otg>;
- phy-names = "usb2-phy";
- extcon = <&usb2phy0>;
- maximum-speed = "high-speed";
- dr_mode = "host";
- status = "okay";
+};
+&sata0 {
- status = "okay";
+};
+/* USB3.0 Host */ +&usb_host1_xhci {
- status = "okay";
+};
+&vop {
- assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
- assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
- status = "okay";
+};
+&vop_mmu {
- status = "okay";
+};
+&vp0 {
- vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
reg = <ROCKCHIP_VOP2_EP_HDMI0>;remote-endpoint = <&hdmi_in_vp0>;- };
+};
+&pinctrl {
- leds {
user_led_pin: user-status-led-pin {rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- usb {
vcc5v0_usb20_host_en: vcc5v0-usb20-host-en {rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;};vcc5v0_usb30_host_en: vcc5v0-usb30-host-en {rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;};vcc5v0_otg_vbus_en: vcc5v0-otg-vbus-en {rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- pcie {
vcc3v3_m2_pcie_en: vcc3v3-m2-pcie-en {rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;};vcc3v3_mini_pcie_en: vcc3v3-mini-pcie-en {rockchip,pins = <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- pmic {
pmic_int: pmic-int {rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;};- };
+}; diff --git a/configs/lubancat-2-rk3568_defconfig b/configs/lubancat-2-rk3568_defconfig new file mode 100644 index 0000000000..40ac1dda4f --- /dev/null +++ b/configs/lubancat-2-rk3568_defconfig @@ -0,0 +1,94 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_TEXT_BASE=0x00a00000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_SF_DEFAULT_MODE=0x2000 +CONFIG_DEFAULT_DEVICE_TREE="rk3568-lubancat-2" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_ROCKCHIP_SPI_IMAGE=y
I do not see any sfc node in board dts, so no need to enable all SPI flash related options.
+CONFIG_SPL_SERIAL=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_SPL_STACK=0x400000 +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-lubancat-2.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x4000000 +CONFIG_SPL_BSS_MAX_SIZE=0x4000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
I recommend adding CONFIG_SPL_DM_SEQ_ALIAS=y here.
+CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_SPL_CLK=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_XTX=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_ROCKCHIP_SFC=y +CONFIG_SYSRESET=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y
We should use USB_DWC3_GENERIC instead of USB_XHCI_DWC3 after the series "rockchip: rk3568: Use dwc3-generic driver".
I made the following fixup commit with somve of the above suggestions when reviewing this board: See https://github.com/Kwiboo/u-boot-rockchip/commit/b9de94dbdc19d54a009f743349c...
Regards, Jonas
+CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_ERRNO_STR=y
participants (2)
-
Andy Yan -
Jonas Karlman