Hi Jonas,
On Sat, 2024-03-02 at 16:28 +0100, Jonas Karlman wrote:
Hi Christopher,
On 2024-03-02 15:34, Christopher Obbard wrote:
Some variants of the ROCK Pi 4 series contain an SPI flash chip, which can be booted from. This patch enables support in U-Boot for building the image for the SPI flash, support for booting U-Boot from the SPI flash chip and support in U-Boot for accessing the SPI flash using `sf` commands.
Not all variants (e.g. ROCK Pi 4B, ROCK 4 Model C Plus, ROCK 4SE) come populated with an SPI flash chip, but have the footprint on the board so a user could solder their own to the board. With this patchset applied, these board variants without an SPI flash chip still boot from MMC.
I have enabled support for both Winbond and XTX SPI flash devices since different hardware variants have different devices populated:
- `rockpi4_v13_sch_20181112.pdf` contains a Winbond part `W25Q64FWZPIG` - `rockpi4_v14_sch_20210114.pdf` contains an XTX part `XT25F32BWOIGT`
The ROCK Pi 4 I have is marked as "ROCK PI 4 v1.48" and contains an SPI flash chip from XTX:
=> sf probe SF: Detected xt25f32 with page size 256 Bytes, erase size 4 KiB, total 4 MiB
In the interest of supporting all board variants and not regressing existing users who boot from MMC, I have enabled support for booting from both SPI flash chip variants in the defconfig and left the environment storage location as MMC to not break existing users who have the environment stored on MMC.
I have also enabled GigaDevice SPI flash chip support, since without it U-Boot (unexplainably) fails to load with an error:
U-Boot SPL 2024.04-rc3-00002-g06b486900e2 (Mar 02 2024 - 13:20:45 +0000) Trying to boot from SPI load_simple_fit: Skip load 'atf-5': image size is 0! initcall failed at call 000000000029beec (err=-11: Try again) ### ERROR ### Please RESET the board ###
This is possibly because of pinctrl no being configured in SPL. I have a big incoming rk3399 series that tries to fix this for most rk3399 boards. It will be a variant of what I did in [1] for rk3328.
Sounds good! Let me know if you want to take these patches in that series, or how you wish to work together to not duplicate work. I am open to suggestions if it makes things easier for Kever to merge ;-).
BROM will only configure pinctrl for each device it tries to locate IDB from, so if it locates IDB in SPL it will not have configured emmc or sd-card. So for SPL to be able to fall back on other storage it will need to do proper pinctrl.
[1] https://patchwork.ozlabs.org/cover/1900345/
Building with `CONFIG_SPL_FIT_SIGNATURE=y` causes an error when booting from SPI flash, so I disabled it:
U-Boot 2024.04-rc3-00010-g2e7974a13b9 (Mar 02 2024 - 14:00:17 +0000) SoC: Rockchip rk3399 Reset cause: unknown reset Model: Radxa ROCK Pi 4A DRAM: initcall failed at call 0000000000228efc (err=-19: No such device) ### ERROR ### Please RESET the board ###
This is unexpected but if your u-boot.bin is close to or larger then 1 MiB the stack and pre-alloc heap may be overlapping with U-Boot proper or the FDT. That can cause all sort of strange and unexpected issues :-)
Have another incoming series to address this for RK3328, RK3399 and ROCK 5A [2]. Should hit list later today, it will be a rework of [3].
Great, please keep me in CC of those series and I will test & rebase my work on top.
Thanks! Chris
[2] https://github.com/Kwiboo/u-boot-rockchip/compare/2011cf069a8b...9767374d6a8... [3] https://patchwork.ozlabs.org/cover/1900376/
Signed-off-by: Christopher Obbard chris.obbard@collabora.com
arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi | 12 ++++++++++++ configs/rock-pi-4-rk3399_defconfig | 15 +++++++++++++-- 2 files changed, 25 insertions(+), 2 deletions(-)
diff --git a/arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi b/arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi index 85ee5770add..04c152a291f 100644 --- a/arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi +++ b/arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi @@ -4,3 +4,15 @@ */ #include "rk3399-rock-pi-4-u-boot.dtsi"
+/ {
- chosen {
u-boot,spl-boot-order = "same-as-spl", &spi_flash,&sdhci, &sdmmc;
I would not recommend adding spi_flash here, especially if you have SPL_FIT_SIGNATURE disabled, and even more so if someone accidentally enable SPL_RAW_IMAGE_SUPPORT.
Ideally, we only load TPL/SPL+FIT from same storage, as provided by same-as-spl, however, if we cannot load from the same storage that TPL/SPL was loaded from, for recovery purposes it is typically easier to fall back on sd-card followed by emmc.
Normally I would expect that if board does not boot TPL/SPL from SPI, there is no real reason to try and load FIT from SPI.
If the FIT cannot be loaded from SPI with same-as-spl alone there is possible some other issue that we need to resolve.
- };
+};
+&spi1 {
- spi_flash: flash@0 {
bootph-all;- };
+}; diff --git a/configs/rock-pi-4-rk3399_defconfig b/configs/rock-pi-4- rk3399_defconfig index 83fc4ad7dab..3a38b51c46b 100644 --- a/configs/rock-pi-4-rk3399_defconfig +++ b/configs/rock-pi-4-rk3399_defconfig @@ -6,25 +6,28 @@ CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 +CONFIG_SF_DEFAULT_SPEED=10000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-pi-4a" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y +CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_EVB_RK3399=y CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_PCI=y CONFIG_DEBUG_UART=y # CONFIG_ANDROID_BOOT_IMAGE is not set -CONFIG_SPL_FIT_SIGNATURE=y CONFIG_LEGACY_IMAGE_FORMAT=y CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-pi-4a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_MISC_INIT_R=y -CONFIG_SPL_MAX_SIZE=0x2e000 +CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y CONFIG_SPL_BSS_START_ADDR=0x400000 @@ -33,6 +36,8 @@ CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set CONFIG_SPL_STACK_R=y CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y @@ -52,6 +57,7 @@ CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent CONFIG_ENV_IS_IN_MMC=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DFU_MMC=y +CONFIG_SPL_DM_SEQ_ALIAS=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y CONFIG_MISC=y @@ -61,6 +67,10 @@ CONFIG_MMC_DW_ROCKCHIP=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_SDMA=y CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_SF_DEFAULT_BUS=1
Would recommend adding following to allow reading SFDP properties from flash, it is what I am doing to all other rk boards with spi flash:
CONFIG_SPI_FLASH_SFDP_SUPPORT=y
Regards, Jonas
+CONFIG_SPI_FLASH_GIGADEVICE=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_XTX=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y CONFIG_NVME_PCI=y @@ -74,6 +84,7 @@ CONFIG_RAM_ROCKCHIP_LPDDR4=y CONFIG_BAUDRATE=1500000 CONFIG_DEBUG_UART_SHIFT=2 CONFIG_SYS_NS16550_MEM32=y +CONFIG_ROCKCHIP_SPI=y CONFIG_SYSRESET=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y
Kernel mailing list -- kernel@mailman.collabora.com To unsubscribe send an email to kernel-leave@mailman.collabora.com This list is managed by https://mailman.collabora.com