Khadas VIM3L uses the same board layout as VIM3, but with an S905D3 chip instead of A311D. Board config is derived from khadas-vim3_defconfig and sei610_defconfig. README is based on README.khadas-vim3; the difference is that VIM3L uses FIP files from the g12a folder in vendor sources not the g12b folder.
Signed-off-by: Christian Hewitt christianshewitt@gmail.com --- board/amlogic/w400/README.khadas-vim3l | 132 +++++++++++++++++++++++++++++++++ configs/khadas-vim3l_defconfig | 62 ++++++++++++++++ 2 files changed, 194 insertions(+) create mode 100644 board/amlogic/w400/README.khadas-vim3l create mode 100644 configs/khadas-vim3l_defconfig
diff --git a/board/amlogic/w400/README.khadas-vim3l b/board/amlogic/w400/README.khadas-vim3l new file mode 100644 index 0000000..b53a67c --- /dev/null +++ b/board/amlogic/w400/README.khadas-vim3l @@ -0,0 +1,132 @@ +U-Boot for Khadas VIM3L +======================= + +Khadas VIM3 is a single board computer manufactured by Shenzhen Wesion +Technology Co., Ltd. with the following specifications: + + - Amlogic S905D3 Arm Cortex-A55 quad-core SoC + - 2GB LPDDR4 SDRAM + - Gigabit Ethernet + - HDMI 2.1 display + - 40-pin GPIO header + - 1 x USB 3.0 Host, 1 x USB 2.0 Host + - eMMC, microSD + - M.2 + - Infrared receiver + +Schematics are available on the manufacturer website. + +Currently the U-Boot port supports the following devices: + - serial + - eMMC, microSD + - Ethernet + - I2C + - Regulators + - Reset controller + - Clock controller + - ADC + +u-boot compilation +================== + + > export ARCH=arm + > export CROSS_COMPILE=aarch64-none-elf- + > make khadas-vim3l_defconfig + > make + +Image creation +============== + +Amlogic doesn't provide sources for the firmware and for tools needed +to create the bootloader image, so it is necessary to obtain them from +the git tree published by the board vendor: + + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-... + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-... + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH + + > DIR=vim3l-u-boot + > git clone --depth 1 \ + https://github.com/khadas/u-boot.git -b khadas-vims-v2015.01 \ + $DIR + + > cd vim3l-u-boot + > make kvim3l_defconfig + > make + > export UBOOTDIR=$PWD + + Go back to mainline U-Boot source tree then : + > mkdir fip + + > cp $UBOOTDIR/build/scp_task/bl301.bin fip/ + > cp $UBOOTDIR/build/board/khadas/kvim3l/firmware/acs.bin fip/ + > cp $UBOOTDIR/fip/g12a/bl2.bin fip/ + > cp $UBOOTDIR/fip/g12a/bl30.bin fip/ + > cp $UBOOTDIR/fip/g12a/bl31.img fip/ + > cp $UBOOTDIR/fip/g12a/ddr3_1d.fw fip/ + > cp $UBOOTDIR/fip/g12a/ddr4_1d.fw fip/ + > cp $UBOOTDIR/fip/g12a/ddr4_2d.fw fip/ + > cp $UBOOTDIR/fip/g12a/diag_lpddr4.fw fip/ + > cp $UBOOTDIR/fip/g12a/lpddr3_1d.fw fip/ + > cp $UBOOTDIR/fip/g12a/lpddr4_1d.fw fip/ + > cp $UBOOTDIR/fip/g12a/lpddr4_2d.fw fip/ + > cp $UBOOTDIR/fip/g12a/piei.fw fip/ + > cp $UBOOTDIR/fip/g12a/aml_ddr.fw fip/ + > cp u-boot.bin fip/bl33.bin + + > sh fip/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + > sh fip/blx_fix.sh \ + fip/bl2.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/acs.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + > $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \ + --output fip/bl30_new.bin.g12a.enc \ + --level v3 + > $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \ + --output fip/bl30_new.bin.enc \ + --level v3 --type bl30 + > $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \ + --output fip/bl31.img.enc \ + --level v3 --type bl31 + > $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \ + --output fip/bl33.bin.enc \ + --level v3 --type bl33 --compress lz4 + > $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \ + --output fip/bl2.n.bin.sig + > $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc \ + --ddrfw1 fip/ddr4_1d.fw \ + --ddrfw2 fip/ddr4_2d.fw \ + --ddrfw3 fip/ddr3_1d.fw \ + --ddrfw4 fip/piei.fw \ + --ddrfw5 fip/lpddr4_1d.fw \ + --ddrfw6 fip/lpddr4_2d.fw \ + --ddrfw7 fip/diag_lpddr4.fw \ + --ddrfw8 fip/aml_ddr.fw \ + --ddrfw9 fip/lpddr3_1d.fw \ + --level v3 + +and then write the image to SD with: + + > DEV=/dev/your_sd_device + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/configs/khadas-vim3l_defconfig b/configs/khadas-vim3l_defconfig new file mode 100644 index 0000000..51e0f80 --- /dev/null +++ b/configs/khadas-vim3l_defconfig @@ -0,0 +1,62 @@ +CONFIG_ARM=y +CONFIG_SYS_BOARD="w400" +CONFIG_ARCH_MESON=y +CONFIG_SYS_TEXT_BASE=0x01000000 +CONFIG_MESON_G12A=y +CONFIG_ENV_SIZE=0x2000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_DEBUG_UART_BASE=0xff803000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_IDENT_STRING=" khadas-vim3l" +CONFIG_DEBUG_UART=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_MISC_INIT_R=y +# CONFIG_DISPLAY_CPUINFO is not set +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_IMI is not set +CONFIG_CMD_GPIO=y +# CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_REGULATOR=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="meson-sm1-khadas-vim3l" +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM_GPIO=y +CONFIG_DM_MMC=y +CONFIG_MMC_MESON_GX=y +CONFIG_PHY_REALTEK=y +CONFIG_DM_ETH=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_MESON_G12A_USB_PHY=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_MESON_G12A=y +CONFIG_POWER_DOMAIN=y +CONFIG_MESON_EE_POWER_DOMAIN=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_RESET=y +CONFIG_DEBUG_UART_MESON=y +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_DEBUG_UART_SKIP_INIT=y +CONFIG_MESON_SERIAL=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_DWC3=y +# CONFIG_USB_DWC3_GADGET is not set +CONFIG_USB_DWC3_MESON_G12A=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e +CONFIG_USB_GADGET_PRODUCT_NUM=0xfada +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_DM_VIDEO=y +CONFIG_VIDEO_MESON=y +CONFIG_VIDEO_DT_SIMPLEFB=y +CONFIG_OF_LIBFDT_OVERLAY=y