On Mon, 2017-01-30 at 15:55 +0100, Alexander Graf wrote:
On 01/29/2017 12:05 AM, Dalon Westergreen wrote:
From: Dalon Westergreen dalon.westergreen@intel.com
Move repeated environment settings for socfpga boards to a common header.
The default values for the boot partition and the OS filesystem partition have changed and as as result the default uboot environment for socfpga boards needs updating.
Move to using CONFIG_DEFAULT_DEVICE_TREE for setting the default linux devicetree used during linux boot.
Signed-off-by: Dalon Westergreen dalon.westergreen@intel.com
include/configs/socfpga_common.h | 35 +++++++++++++++++++++++++++++++++-- 1 file changed, 33 insertions(+), 2 deletions(-)
diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h index 6285266..744aee9 100644 --- a/include/configs/socfpga_common.h +++ b/include/configs/socfpga_common.h @@ -312,10 +312,14 @@ unsigned int cm_get_qspi_controller_clk_hz(void); /* SPL SDMMC boot support */ #ifdef CONFIG_SPL_MMC_SUPPORT #if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT) -#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 2 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img" +#ifdef CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 +#else +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 2 +#endif #else -#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1 +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 3 #endif #endif @@ -336,5 +340,32 @@ unsigned int cm_get_qspi_controller_clk_hz(void); * Stack setup */ #define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
+/* Extra Environment */ +#ifndef CONFIG_EXTRA_ENV_SETTINGS +#define CONFIG_EXTRA_ENV_SETTINGS \
- "verify=n\0" \
- "loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
- "bootimage=" CONFIG_BOOTFILE "\0" \
- "fdt_addr=100\0" \
- "fdtimage=" CONFIG_DEFAULT_FDT_FILE "\0" \
- "ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
"bootm ${loadaddr} - ${fdt_addr}\0" \- "mmcroot=/dev/mmcblk0p2\0" \
- "mmcboot=setenv bootargs " CONFIG_BOOTARGS \
" root=${mmcroot} rw rootwait;" \"bootz ${loadaddr} - ${fdt_addr}\0" \- "mmcload=mmc rescan;" \
"load mmc 0:1 ${loadaddr} ${bootimage};" \"load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \- "qspiload=sf probe && mtdparts default && run ubiload\0" \
- "qspiboot=setenv bootargs " CONFIG_BOOTARGS \
" ubi.mtd=1,64 root=ubi0:rootfs rw rootfstype=ubifs;"\"bootz ${loadaddr} - ${fdt_addr}\0" \- "ubiload=ubi part UBI && ubifsmount ubi0 && " \
"ubifsload ${loadaddr} /boot/${bootimage} && " \"ubifsload ${fdt_addr} /boot/${fdtimage}\0"What is the default bootcmd with this environment? Also, keep in mind that it's 2017. Is there any good reason not to default to distro boot?
Alex
The default is board dependent, but in general is mmcboot. there is no good reason to not use distro boot. Frank Kunz submitted something to that end for one of these boards the other day. once the environment common, we will move to distro boot.