This should clean up a warning about a missing phy-cells
Signed-off-by: Adam Ford aford173@gmail.com
diff --git a/arch/arm/dts/logicpd-som-lv.dtsi b/arch/arm/dts/logicpd-som-lv.dtsi index 46dae55..c1aa7a4 100644 --- a/arch/arm/dts/logicpd-som-lv.dtsi +++ b/arch/arm/dts/logicpd-som-lv.dtsi @@ -33,11 +33,12 @@ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv"; reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */ + #phy-cells = <0>; }; };
&gpmc { - ranges = <0 0 0x00000000 0x1000000>; /* CS0: 16MB for NAND */ + ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
nand@0,0 { compatible = "ti,omap2-nand"; @@ -66,38 +67,11 @@ gpmc,device-width = <2>; #address-cells = <1>; #size-cells = <1>; - - /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */ - - x-loader@0 { - label = "x-loader"; - reg = <0 0x80000>; - }; - - bootloaders@80000 { - label = "u-boot"; - reg = <0x80000 0x1e0000>; - }; - - bootloaders_env@260000 { - label = "u-boot-env"; - reg = <0x260000 0x20000>; - }; - - kernel@280000 { - label = "kernel"; - reg = <0x280000 0x400000>; - }; - - filesystem@680000 { - label = "fs"; - reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */ - }; }; };
&i2c1 { - clock-frequency = <400000>; + clock-frequency = <2600000>;
twl: twl@48 { reg = <0x48>; @@ -121,7 +95,7 @@
&mmc3 { interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>; - pinctrl-0 = <&mmc3_pins>; + pinctrl-0 = <&mmc3_pins &wl127x_gpio>; pinctrl-names = "default"; vmmc-supply = <&wl12xx_vmmc>; non-removable; @@ -132,8 +106,8 @@ wlcore: wlcore@2 { compatible = "ti,wl1273"; reg = <2>; - interrupt-parent = <&gpio5>; - interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ + interrupt-parent = <&gpio1>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */ ref-clock-frequency = <26000000>; }; }; @@ -157,8 +131,6 @@ OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ - OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ - OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */ OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */ OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */ >; @@ -228,6 +200,12 @@ OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ >; }; + wl127x_gpio: pinmux_wl127x_gpio_pin { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */ + OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */ + >; + }; };
&omap3_pmx_core2 {