On 4/7/20 11:15 PM, Benedikt Grassl wrote:
Currently, the entry "bus-width = <8>" in the ZynqMP's sdhci nodes is not evaluated. This results in the bus width staying at its default value (4 bit in HS200 mode). Fix this by calling mmc_of_parse. This function also checks for the "no-1-8-v" and "max-frequency" entries. Remove the handling of those nodes from this driver.
Signed-off-by: Benedikt Grassl Benedikt.Grassl@rohde-schwarz.com
drivers/mmc/sdhci.c | 3 +-- drivers/mmc/zynq_sdhci.c | 15 ++++++--------- include/sdhci.h | 1 - 3 files changed, 7 insertions(+), 12 deletions(-)
diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c index 520c9f9feb..372dc0a820 100644 --- a/drivers/mmc/sdhci.c +++ b/drivers/mmc/sdhci.c @@ -839,8 +839,7 @@ int sdhci_setup_cfg(struct mmc_config *cfg, struct sdhci_host *host, cfg->host_caps &= ~MMC_MODE_HS_52MHz; }
- if (!(cfg->voltages & MMC_VDD_165_195) ||
(host->quirks & SDHCI_QUIRK_NO_1_8_V))
- if (!(cfg->voltages & MMC_VDD_165_195)) caps_1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50);
diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c index da3ff53da1..cfa61af265 100644 --- a/drivers/mmc/zynq_sdhci.c +++ b/drivers/mmc/zynq_sdhci.c @@ -22,14 +22,12 @@ DECLARE_GLOBAL_DATA_PTR; struct arasan_sdhci_plat { struct mmc_config cfg; struct mmc mmc;
- unsigned int f_max;
};
struct arasan_sdhci_priv { struct sdhci_host *host; u8 deviceid; u8 bank;
- u8 no_1p8;
};
#if defined(CONFIG_ARCH_ZYNQMP) @@ -238,8 +236,9 @@ static int arasan_sdhci_probe(struct udevice *dev) host->quirks |= SDHCI_QUIRK_BROKEN_HISPD_MODE; #endif
- if (priv->no_1p8)
host->quirks |= SDHCI_QUIRK_NO_1_8_V;
ret = mmc_of_parse(dev, &plat->cfg);
if (ret)
return ret;host->max_clk = clock;
@@ -247,10 +246,12 @@ static int arasan_sdhci_probe(struct udevice *dev) host->mmc->dev = dev; host->mmc->priv = host;
- ret = sdhci_setup_cfg(&plat->cfg, host, plat->f_max,
- ret = sdhci_setup_cfg(&plat->cfg, host,
CONFIG_ZYNQ_SDHCI_MAX_FREQ, CONFIG_ZYNQ_SDHCI_MIN_FREQ);
you have removed the parsing "max-frequency" from below code, because it's parsed from mmc_of_parse(). But It's passing to CONFIG_ZYNQ_SDHCI_MAX_FREQ again. Is it correct? Could you check one more?
Best Regards, Jaehoon Chung
if (ret) return ret;
upriv->mmc = host->mmc;
return sdhci_probe(dev);
@@ -258,7 +259,6 @@ static int arasan_sdhci_probe(struct udevice *dev)
static int arasan_sdhci_ofdata_to_platdata(struct udevice *dev) {
struct arasan_sdhci_plat *plat = dev_get_platdata(dev); struct arasan_sdhci_priv *priv = dev_get_priv(dev);
priv->host = calloc(1, sizeof(struct sdhci_host));
@@ -277,10 +277,7 @@ static int arasan_sdhci_ofdata_to_platdata(struct udevice *dev)
priv->deviceid = dev_read_u32_default(dev, "xlnx,device_id", -1); priv->bank = dev_read_u32_default(dev, "xlnx,mio_bank", -1);
priv->no_1p8 = dev_read_bool(dev, "no-1-8-v");
plat->f_max = dev_read_u32_default(dev, "max-frequency",
CONFIG_ZYNQ_SDHCI_MAX_FREQ);return 0;
}
diff --git a/include/sdhci.h b/include/sdhci.h index aa4378fd57..0ef8c2ed62 100644 --- a/include/sdhci.h +++ b/include/sdhci.h @@ -243,7 +243,6 @@ #define SDHCI_QUIRK_BROKEN_HISPD_MODE BIT(5) #define SDHCI_QUIRK_WAIT_SEND_CMD (1 << 6) #define SDHCI_QUIRK_USE_WIDE8 (1 << 8) -#define SDHCI_QUIRK_NO_1_8_V (1 << 9)
/* to make gcc happy */ struct sdhci_host;