Am 12.05.24 um 23:37 schrieb Jonas Karlman:
Hi Alex,
On 2024-05-12 21:49, Alex Bee wrote:
Am 11.05.24 um 20:47 schrieb Jonas Karlman:
Hi Alex,
On 2024-05-11 19:44, Alex Bee wrote:
Hi Jonas,
Am 11.05.24 um 13:28 schrieb Jonas Karlman:
This series add gpio request() and pinctrl gpio_request_enable() ops so that a gpio requested pin automatically use gpio pinmux and U-Boot behaves more similar to Linux kernel.
I'm not sure that's a good idea. While linux does it the same way, we really shouldn't expect every software/os/ … which uses DT (now or in future) to implicitly switch the pin function when using a pin as gpio. So the real fix would probably be to add the the correct pinctrl settings to the upstream DT of those boards and sync it later on (not sure those if those SoCs already using OF_UPSTREAM) and leave the -u-boot.dtsi-"hack" alone for now.
I fully agree that the pinctrl for the problematic boards should be corrected in upstream DT, but that is a separate issue and should not block adding support for the request()/gpio_request_enable() ops.
While the pcie reset-gpios full board freeze that was my driving factor to fully implement the gpio request() ops it is not the only use case, using the gpio cmd on a pin that use a non-gpio pinmux is another.
Or do you see any technical issue with having the gpio request() ops implemented and having it ensure gpio pinmux is used on a gpio requested pin? Similar to how gpio/pinctrl is behaving in Linux and on some other platforms in U-Boot?
No, no general ("technical") issue with adding a .request hook to the gpio driver. But now you are now moving the original workaround to an even more invisible place which does things implicitly. Maybe just don't remove the pinctrl from the boards u-boot-dtsi's - just replace it with
&pcie30x2m1_pins { rockchip,pins = <2 RK_PD4 4 &pcfg_pull_none>, <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>, <2 RK_PD5 4 &pcfg_pull_none>; };
Even if it would (now) work without. It, at least, documents that there are things left to do for the upstream DT.
This is what I was doing when testing PCIe on ROCK 3B, I would still like to drop the "bad" workaround for ROCK 3A and E25 and have it fixed in upstream DT and let it trickle back now that RK356x use OF_UPSTREAM.
I do not see the point of keeping a workaround that no longer is needed, especially when there is plans to also adjust upstream DT.
Yeah, sure: but that certainly should be done/happen first, before it's removed here. Everybody knows how long that takes, patches being forgotten ....
What you were saying in reply to Mark's email is not completely true: Not all pins are initialized with gpio func as default. It actually depends on the pin which function the bootrom sets initially. In case of RK356x's GPIO2_PD6 (the pin in question) it's BT656_D6M0 (func2), for instance. So, in fact, you are changing it's function when implicitly setting it's func to gpio (func0).
Sure, bootrom will change pin func on some pins so that it e.g. can read from storage etc, but in general gpio mux is what most pins will use after POR.
On my ROCK 3A I see the pcie30x2m1 pins using func0 (gpio) after POR:
=> pinmux status GPIO2_D4 : gpio GPIO2_D5 : gpio GPIO2_D6 : gpio
And with this after a "pci enum":
=> pinmux status GPIO2_D4 : func-4 GPIO2_D5 : func-4 GPIO2_D6 : gpio
Not sure why your board would use BT656_D6M0 (func2) after POR unless there is some other code writing to the IOMUX regs.
Oh, I haven't checked on an actual board - I trusted the TRM [0], page 253 GRF_GPIO2D_IOMUX_H[10:8] is (should be) 0x2. But (sadly) there are lot of blobs involved. for RK35xx SoCs - so maybe something switches the func for this pin for some reason.
The only thing this series changes is that when a U-Boot drivers use e.g. gpio_request_by_name("reset-gpios") the referenced pin in DT will implicitly be configured for gpio func.
I would still like to understand if there is any other reason, not related to dropping current "bad" PCIe DT workaround, to not to adopt this implicit configuration and match Linux kernel?
Generally speaking: device trees _must_ represent the actual hardware completely independent from any driver or any software. They are NOT helpers or configuration for drivers. Drivers can use them and have to adapt to them - not vice versa. So: Being as explict as possible is a must. At some point, it is planned, to split whole DT "subsystem" from the linux kernel. I also have a vague remembering (some mailing list discussion I can't find right now), that this whole implicit function switching of pins is sort of "not welcome" in linux anymore. So adding it here also is sort of a "step back" from that POV.
Alex
[0] https://opensource.rock-chips.com/images/2/26/Rockchip_RK3568_TRM_Part1_V1.3...
Regards, Jonas
Alex
Regards, Jonas
Alex
With the gpio and pinctrl ops implemented this series also remove a PCIe reset-gpios related device lock-up workaround from board u-boot.dtsi.
PX30, RK3066, RK3188, RK356x and RK3588 are the only SoCs that currently define gpio-ranges props and is affected by this series.
A follow up series adding support for the pinmux status cmd will also add gpio-ranges props for remaining RK SoCs.
Jonas Karlman (4): pinctrl: rockchip: Add gpio_request_enable() ops gpio: rockchip: Add request() ops rockchip: rk3568-rock-3a: Drop PCIe reset-gpios workaround rockchip: rk3568-radxa-e25: Drop PCIe reset-gpios workaround
arch/arm/dts/rk3568-radxa-e25-u-boot.dtsi | 12 ------- arch/arm/dts/rk3568-rock-3a-u-boot.dtsi | 12 ------- drivers/gpio/rk_gpio.c | 10 ++++++ .../pinctrl/rockchip/pinctrl-rockchip-core.c | 31 +++++++++++++++++++ 4 files changed, 41 insertions(+), 24 deletions(-)