This UART permits different register spacing. To support the debug UART on devices which have a spacing other than 1 byte, allow the shift value to be specified.
Signed-off-by: Simon Glass sjg@chromium.org ---
drivers/serial/Kconfig | 10 ++++++++++ drivers/serial/ns16550.c | 25 +++++++++++++++---------- 2 files changed, 25 insertions(+), 10 deletions(-)
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 1686a1f..54e6f26 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -66,6 +66,16 @@ config DEBUG_UART_CLOCK A default should be provided by your board, but if not you will need to use the correct value here.
+config DEBUG_UART_SHIFT + int "UART register shift" + depends on DEBUG_UART + default 0 if DEBUG_UART + help + Some UARTs (notably ns16550) support different register layouts + where the registers are spaced either as bytes, words or some other + value. Use this value to specify the shift to use, where 0=byte + registers, 2=32-bit word registers, etc. + config UNIPHIER_SERIAL bool "UniPhier on-chip UART support" depends on ARCH_UNIPHIER && DM_SERIAL diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c index eb00f1c..54f432f 100644 --- a/drivers/serial/ns16550.c +++ b/drivers/serial/ns16550.c @@ -253,15 +253,20 @@ void debug_uart_init(void) */ baud_divisor = calc_divisor(com_port, CONFIG_DEBUG_UART_CLOCK, CONFIG_BAUDRATE); - - serial_out_shift(&com_port->ier, 0, CONFIG_SYS_NS16550_IER); - serial_out_shift(&com_port->mcr, 0, UART_MCRVAL); - serial_out_shift(&com_port->fcr, 0, UART_FCRVAL); - - serial_out_shift(&com_port->lcr, 0, UART_LCR_BKSE | UART_LCRVAL); - serial_out_shift(&com_port->dll, 0, baud_divisor & 0xff); - serial_out_shift(&com_port->dlm, 0, (baud_divisor >> 8) & 0xff); - serial_out_shift(&com_port->lcr, 0, UART_LCRVAL); + baud_divisor = 13; + serial_out_shift(&com_port->ier, CONFIG_DEBUG_UART_SHIFT, + CONFIG_SYS_NS16550_IER); + serial_out_shift(&com_port->mcr, CONFIG_DEBUG_UART_SHIFT, UART_MCRVAL); + serial_out_shift(&com_port->fcr, CONFIG_DEBUG_UART_SHIFT, UART_FCRVAL); + + serial_out_shift(&com_port->lcr, CONFIG_DEBUG_UART_SHIFT, + UART_LCR_BKSE | UART_LCRVAL); + serial_out_shift(&com_port->dll, CONFIG_DEBUG_UART_SHIFT, + baud_divisor & 0xff); + serial_out_shift(&com_port->dlm, CONFIG_DEBUG_UART_SHIFT, + (baud_divisor >> 8) & 0xff); + serial_out_shift(&com_port->lcr, CONFIG_DEBUG_UART_SHIFT, + UART_LCRVAL); }
static inline void _debug_uart_putc(int ch) @@ -270,7 +275,7 @@ static inline void _debug_uart_putc(int ch)
while (!(serial_in_shift(&com_port->lsr, 0) & UART_LSR_THRE)) ; - serial_out_shift(&com_port->thr, 0, ch); + serial_out_shift(&com_port->thr, CONFIG_DEBUG_UART_SHIFT, ch); }
DEBUG_UART_FUNCS