[ fsl_esdhc commit 7e48a028a42c111ba38a90b86e5f57dace980fa0 ]
First, we need the waterlevel setting for PIO mode only. Secondy, both DMA setup code is identical for both directions, except for the data pointer. Thus, unify them.
Signed-off-by: Michael Walle michael@walle.cc Signed-off-by: Sean Anderson sean.anderson@seco.com Reviewed-by: Jaehoon Chung jh80.chung@samsung.com ---
(no changes since v1)
drivers/mmc/fsl_esdhc_imx.c | 89 ++++++++++++++++++++++--------------- 1 file changed, 52 insertions(+), 37 deletions(-)
diff --git a/drivers/mmc/fsl_esdhc_imx.c b/drivers/mmc/fsl_esdhc_imx.c index 283af35a81..6c25a77c79 100644 --- a/drivers/mmc/fsl_esdhc_imx.c +++ b/drivers/mmc/fsl_esdhc_imx.c @@ -279,59 +279,74 @@ static void esdhc_pio_read_write(struct fsl_esdhc_priv *priv, } #endif
-static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc, - struct mmc_data *data) +#ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO +static void esdhc_setup_watermark_level(struct fsl_esdhc_priv *priv, + struct mmc_data *data) { - int timeout; - uint trans_bytes = data->blocksize * data->blocks; struct fsl_esdhc *regs = priv->esdhc_regs; - uint wml_value; - - wml_value = data->blocksize/4; + uint wml_value = data->blocksize / 4;
if (data->flags & MMC_DATA_READ) { if (wml_value > WML_RD_WML_MAX) wml_value = WML_RD_WML_MAX_VAL;
esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK, wml_value); -#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO - priv->dma_addr = dma_map_single(data->dest, trans_bytes, - mmc_get_dma_dir(data)); - if (upper_32_bits(priv->dma_addr)) - printf("Cannot use 64 bit addresses with SDMA\n"); - esdhc_write32(®s->dsaddr, lower_32_bits(priv->dma_addr)); -#endif } else { if (wml_value > WML_WR_WML_MAX) wml_value = WML_WR_WML_MAX_VAL; - if (priv->wp_enable) { - if ((esdhc_read32(®s->prsstat) & - PRSSTAT_WPSPL) == 0) { - printf("\nThe SD card is locked. Can not write to a locked card.\n\n"); - return -ETIMEDOUT; - } - } else { -#if CONFIG_IS_ENABLED(DM_GPIO) - if (dm_gpio_is_valid(&priv->wp_gpio) && - dm_gpio_get_value(&priv->wp_gpio)) { - printf("\nThe SD card is locked. Can not write to a locked card.\n\n"); - return -ETIMEDOUT; - } -#endif - }
esdhc_clrsetbits32(®s->wml, WML_WR_WML_MASK, - wml_value << 16); -#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO - priv->dma_addr = dma_map_single((void *)data->src, trans_bytes, - mmc_get_dma_dir(data)); - if (upper_32_bits(priv->dma_addr)) - printf("Cannot use 64 bit addresses with SDMA\n"); - esdhc_write32(®s->dsaddr, lower_32_bits(priv->dma_addr)); -#endif + wml_value << 16); } +} +#endif
+static void esdhc_setup_dma(struct fsl_esdhc_priv *priv, struct mmc_data *data) +{ + uint trans_bytes = data->blocksize * data->blocks; + struct fsl_esdhc *regs = priv->esdhc_regs; + void *buf; + + if (data->flags & MMC_DATA_WRITE) + buf = (void *)data->src; + else + buf = data->dest; + + priv->dma_addr = dma_map_single(buf, trans_bytes, + mmc_get_dma_dir(data)); + if (upper_32_bits(priv->dma_addr)) + printf("Cannot use 64 bit addresses with SDMA\n"); + esdhc_write32(®s->dsaddr, lower_32_bits(priv->dma_addr)); esdhc_write32(®s->blkattr, data->blocks << 16 | data->blocksize); +} + +static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc, + struct mmc_data *data) +{ + int timeout; + bool is_write = data->flags & MMC_DATA_WRITE; + struct fsl_esdhc *regs = priv->esdhc_regs; + + if (is_write) { + if (priv->wp_enable && !(esdhc_read32(®s->prsstat) & PRSSTAT_WPSPL)) { + printf("Cannot write to locked SD card.\n"); + return -EINVAL; + } else { +#if CONFIG_IS_ENABLED(DM_GPIO) + if (dm_gpio_is_valid(&priv->wp_gpio) && + dm_gpio_get_value(&priv->wp_gpio)) { + printf("Cannot write to locked SD card.\n"); + return -EINVAL; + } +#endif + } + } + +#ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO + esdhc_setup_watermark_level(priv, data); +#else + esdhc_setup_dma(priv, data); +#endif
/* Calculate the timeout period for data transactions */ /*