Dear Bo Shen,
On 28.02.13 08:00, Bo Shen wrote:
Add sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB support
Signed-off-by: Bo Shen voice.shen@atmel.com
MAINTAINERS | 1 + arch/arm/cpu/armv7/at91/Makefile | 49 +++++ arch/arm/cpu/armv7/at91/clock.c | 116 +++++++++++ arch/arm/cpu/armv7/at91/cpu.c | 115 +++++++++++ arch/arm/cpu/armv7/at91/reset.c | 44 +++++ arch/arm/cpu/armv7/at91/sama5d3_devices.c | 219 ++++++++++++++++++++ arch/arm/cpu/armv7/at91/timer.c | 136 +++++++++++++ arch/arm/include/asm/arch-at91/at91_dbu.h | 4 + arch/arm/include/asm/arch-at91/at91_pmc.h | 7 +- arch/arm/include/asm/arch-at91/clk.h | 1 + arch/arm/include/asm/arch-at91/hardware.h | 2 + arch/arm/include/asm/arch-at91/sama5d3.h | 220 +++++++++++++++++++++ arch/arm/include/asm/arch-at91/sama5d3_smc.h | 79 ++++++++ board/atmel/sama5d3xek/Makefile | 48 +++++ board/atmel/sama5d3xek/sama5d3xek.c | 274 ++++++++++++++++++++++++++ boards.cfg | 3 + include/configs/sama5d3xek.h | 268 +++++++++++++++++++++++++ 17 files changed, 1585 insertions(+), 1 deletion(-) create mode 100644 arch/arm/cpu/armv7/at91/Makefile create mode 100644 arch/arm/cpu/armv7/at91/clock.c create mode 100644 arch/arm/cpu/armv7/at91/cpu.c create mode 100644 arch/arm/cpu/armv7/at91/reset.c create mode 100644 arch/arm/cpu/armv7/at91/sama5d3_devices.c create mode 100644 arch/arm/cpu/armv7/at91/timer.c create mode 100644 arch/arm/include/asm/arch-at91/sama5d3.h create mode 100644 arch/arm/include/asm/arch-at91/sama5d3_smc.h create mode 100644 board/atmel/sama5d3xek/Makefile create mode 100644 board/atmel/sama5d3xek/sama5d3xek.c create mode 100644 include/configs/sama5d3xek.h
diff --git a/MAINTAINERS b/MAINTAINERS index 45e2dd4..1f22449 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -909,6 +909,7 @@ Matt Sealey matt@genesi-usa.com
Bo Shen voice.shen@atmel.com at91sam9x5ek ARM926EJS (AT91SAM9G15,G25,G35,X25,X35 SoC)
- sama5d3xek ARMV7 (SAMA5D31, D33, D34, D35 SoC)
Michal Simek monstr@monstr.eu
diff --git a/arch/arm/cpu/armv7/at91/Makefile b/arch/arm/cpu/armv7/at91/Makefile new file mode 100644 index 0000000..f2aaa0e --- /dev/null +++ b/arch/arm/cpu/armv7/at91/Makefile @@ -0,0 +1,49 @@ +# +# (C) Copyright 2000-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
How about your copyright here?
+# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +#
+include $(TOPDIR)/config.mk
+LIB = $(obj)lib$(SOC).o
+COBJS-$(CONFIG_SAMA5D3) += sama5d3_devices.o +COBJS-y += clock.o +COBJS-y += cpu.o +COBJS-y += reset.o +COBJS-y += timer.o
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y))
+all: $(obj).depend $(LIB)
+$(LIB): $(OBJS)
- $(call cmd_link_o_target, $(OBJS))
+#########################################################################
+# defines $(obj).depend target +include $(SRCTREE)/rules.mk
+sinclude $(obj).depend
+######################################################################### diff --git a/arch/arm/cpu/armv7/at91/clock.c b/arch/arm/cpu/armv7/at91/clock.c new file mode 100644 index 0000000..5fdefcc --- /dev/null +++ b/arch/arm/cpu/armv7/at91/clock.c @@ -0,0 +1,116 @@ +/*
- [origin: Linux kernel linux/arch/arm/mach-at91/clock.c]
- Copyright (C) 2005 David Brownell
- Copyright (C) 2005 Ivan Kokshaysky
- Copyright (C) 2009 Jean-Christophe PLAGNIOL-VILLARD plagnioj@jcrosoft.com
your copyright?
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation; either version 2 of the License, or
- (at your option) any later version.
- */
+#include <common.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h>
+#if !defined(CONFIG_AT91FAMILY) +# error You need to define CONFIG_AT91FAMILY in your board config! +#endif
+DECLARE_GLOBAL_DATA_PTR;
+static unsigned long at91_css_to_rate(unsigned long css) +{
- switch (css) {
- case AT91_PMC_MCKR_CSS_SLOW:
return CONFIG_SYS_AT91_SLOW_CLOCK;- case AT91_PMC_MCKR_CSS_MAIN:
return gd->arch.main_clk_rate_hz;- case AT91_PMC_MCKR_CSS_PLLA:
return gd->arch.plla_rate_hz;- case AT91_PMC_MCKR_CSS_PLLB:
return gd->arch.pllb_rate_hz;- }
- return 0;
+}
+static u32 at91_pll_rate(u32 freq, u32 reg) +{
- unsigned mul, div;
- div = reg & 0xff;
- mul = (reg >> 18) & 0x7ff;
The CKGR_PLLAR states that the MULA is 8 bit wide. Is the mask here intended? I see, it is stolen from the arm926ejs variant, has anyone checked that before ;)
- if (div && mul) {
freq /= div;freq *= mul + 1;- } else {
freq = 0;- }
- return freq;
+}
+int at91_clock_init(unsigned long main_clock) +{
- unsigned freq, mckr;
- at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+#ifndef CONFIG_SYS_AT91_MAIN_CLOCK
- unsigned tmp;
- /*
* When the bootloader initialized the main oscillator correctly,* there's no problem using the cycle counter. But if it didn't,* or when using oscillator bypass mode, we must be told the speed* of the main clock.*/- if (!main_clock) {
do {tmp = readl(&pmc->mcfr);} while (!(tmp & AT91_PMC_MCFR_MAINRDY));tmp &= AT91_PMC_MCFR_MAINF_MASK;main_clock = tmp * (CONFIG_SYS_AT91_SLOW_CLOCK / 16);- }
+#endif
- gd->arch.main_clk_rate_hz = main_clock;
- /* report if PLLA is more than mildly overclocked */
- gd->arch.plla_rate_hz = at91_pll_rate(main_clock, readl(&pmc->pllar));
- /*
* MCK and CPU derive from one of those primary clocks.* For now, assume this parentage won't change.*/- mckr = readl(&pmc->mckr);
- /* plla divisor by 2 */
- gd->arch.plla_rate_hz /= (1 << ((mckr & 1 << 12) >> 12));
Hasn't the unary '&' higher precedence than the binary operator '<<'? Shouldn't we write '(mckr & (1<<12))' instead? Why shifting by 12 right-side and then 1 left-side?
Why not just this:
---8<--- if (mckr & (1<<12)) gd->arch.plla_rate_hz >>= 1; /* plladiv2 is set */ --->8---
- gd->arch.mck_rate_hz = at91_css_to_rate(mckr & AT91_PMC_MCKR_CSS_MASK);
- freq = gd->arch.mck_rate_hz;
- /* prescale */
- freq /= (1 << ((mckr & (AT91_PMC_MCKR_PRES_MASK << 2)) >> 4));
Can you please redefine the AT91_PMC_MCR_PRES_MASK instead of shifting it here 2 bits?
- gd->arch.mck_rate_hz = (mckr & AT91_PMC_MCKR_MDIV_MASK) ==
(AT91_PMC_MCKR_MDIV_2 | AT91_PMC_MCKR_MDIV_4)? freq / 3: freq / (1 << ((mckr & AT91_PMC_MCKR_MDIV_MASK) >> 8));
I feel this statement is a bit long for a if-else-shortcut, this is a 4 liner! Can you please use concrete if/else here?
- gd->arch.cpu_clk_rate_hz = freq;
- return 0;
+}
+void at91_periph_clk_enable(int id) +{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
The write protect is meant to be right here?
- if (id > 31)
writel(1 << (id - 32), &pmc->pcer1);- else
writel(1 << id, &pmc->pcer);+} diff --git a/arch/arm/cpu/armv7/at91/cpu.c b/arch/arm/cpu/armv7/at91/cpu.c new file mode 100644 index 0000000..643b359 --- /dev/null +++ b/arch/arm/cpu/armv7/at91/cpu.c @@ -0,0 +1,115 @@ +/*
- (C) Copyright 2010
- Reinhard Meyer, reinhard.meyer@emk-elektronik.de
- (C) Copyright 2009
- Jean-Christophe PLAGNIOL-VILLARD plagnioj@jcrosoft.com
your copyright here?
- See file CREDITS for list of people who contributed to this
- project.
- This program is free software; you can redistribute it and/or
- modify it under the terms of the GNU General Public License as
- published by the Free Software Foundation; either version 2 of
- the License, or (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- MA 02111-1307 USA
- */
+#include <common.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/at91_dbu.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_pit.h> +#include <asm/arch/at91_gpbr.h> +#include <asm/arch/clk.h>
+#ifndef CONFIG_SYS_AT91_MAIN_CLOCK +#define CONFIG_SYS_AT91_MAIN_CLOCK 0 +#endif
+int arch_cpu_init(void) +{
- return at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK);
+}
+void arch_preboot_os(void) +{
- ulong cpiv;
- at91_pit_t *pit = (at91_pit_t *) ATMEL_BASE_PIT;
- cpiv = AT91_PIT_MR_PIV_MASK(readl(&pit->piir));
- /*
* Disable PITC* Add 0x1000 to current counter to stop it faster* without waiting for wrapping back to 0*/- writel(cpiv + 0x1000, &pit->mr);
+}
+#if defined(CONFIG_DISPLAY_CPUINFO) +int print_cpuinfo(void) +{
- char buf[32];
- printf("CPU: %s\n", get_cpu_name());
- printf("Crystal frequency: %8s MHz\n",
strmhz(buf, get_main_clk_rate()));- printf("CPU clock : %8s MHz\n",
strmhz(buf, get_cpu_clk_rate()));- printf("Master clock : %8s MHz\n",
strmhz(buf, get_mck_clk_rate()));- return 0;
+} +#endif
+#ifdef CONFIG_BOOTCOUNT_LIMIT +/*
- We combine the BOOTCOUNT_MAGIC and bootcount in one 32-bit register.
- This is done so we need to use only one of the four GPBR registers.
- */
+void bootcount_store(ulong a) +{
- at91_gpbr_t *gpbr = (at91_gpbr_t *) ATMEL_BASE_GPBR;
- writel((BOOTCOUNT_MAGIC & 0xffff0000) | (a & 0x0000ffff),
&gpbr->reg[AT91_GPBR_INDEX_BOOTCOUNT]);+}
+ulong bootcount_load(void) +{
- at91_gpbr_t *gpbr = (at91_gpbr_t *) ATMEL_BASE_GPBR;
- ulong val = readl(&gpbr->reg[AT91_GPBR_INDEX_BOOTCOUNT]);
- if ((val & 0xffff0000) != (BOOTCOUNT_MAGIC & 0xffff0000))
return 0;- else
return val & 0x0000ffff;+}
+#endif /* CONFIG_BOOTCOUNT_LIMIT */
+void enable_caches(void) +{
- return 0;
+}
+unsigned int get_chip_id(void) +{
- return readl(ATMEL_BASE_DBGU + AT91_DBU_CIDR) & ~AT91_DBU_CIDR_MASK;
+}
+unsigned int get_extension_chip_id(void) +{
- return readl(ATMEL_BASE_DBGU + AT91_DBU_EXID);
+} diff --git a/arch/arm/cpu/armv7/at91/reset.c b/arch/arm/cpu/armv7/at91/reset.c new file mode 100644 index 0000000..20383f2 --- /dev/null +++ b/arch/arm/cpu/armv7/at91/reset.c @@ -0,0 +1,44 @@ +/*
- (C) Copyright 2007-2008
- Stelian Pop stelian@popies.net
- Lead Tech Design <www.leadtechdesign.com>
your copyright?
- See file CREDITS for list of people who contributed to this
- project.
- This program is free software; you can redistribute it and/or
- modify it under the terms of the GNU General Public License as
- published by the Free Software Foundation; either version 2 of
- the License, or (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- MA 02111-1307 USA
- */
+#include <common.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/at91_rstc.h>
+/* Reset the cpu by telling the reset controller to do so */ +void reset_cpu(ulong ignored) +{
- at91_rstc_t *rstc = (at91_rstc_t *) ATMEL_BASE_RSTC;
- writel(AT91_RSTC_KEY
| AT91_RSTC_CR_PROCRST /* Processor Reset */| AT91_RSTC_CR_PERRST /* Peripheral Reset */+#ifdef CONFIG_AT91RESET_EXTRST
| AT91_RSTC_CR_EXTRST /* External Reset (assert nRST pin) */+#endif
, &rstc->cr);- /* never reached */
- do { } while (1);
+} diff --git a/arch/arm/cpu/armv7/at91/sama5d3_devices.c b/arch/arm/cpu/armv7/at91/sama5d3_devices.c new file mode 100644 index 0000000..e5474e0 --- /dev/null +++ b/arch/arm/cpu/armv7/at91/sama5d3_devices.c @@ -0,0 +1,219 @@ +/*
- Copyright (C) 2012-2013 Atmel Corporation
Your email here?
- See file CREDITS for list of people who contributed to this
- project.
- This program is free software; you can redistribute it and/or
- modify it under the terms of the GNU General Public License as
- published by the Free Software Foundation; either version 2 of
- the License, or (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- MA 02111-1307 USA
- */
+#include <common.h> +#include <asm/arch/sama5d3.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> +#include <asm/arch/gpio.h> +#include <asm/io.h>
+/*
- if CONFIG_AT91_GPIO_PULLUP ist set, keep pullups on on all
- peripheral pins. Good to have if hardware is soldered optionally
- or in case of SPI no slave is selected. Avoid lines to float
- needlessly. Use a short local PUP define.
- Due to errata "TXD floats when CTS is inactive" pullups are always
- on for TXD pins.
- */
+#ifdef CONFIG_AT91_GPIO_PULLUP +# define PUP CONFIG_AT91_GPIO_PULLUP +#else +# define PUP 0 +#endif
+unsigned int has_emac() +{
- return cpu_is_sama5d31() || cpu_is_sama5d35();
+}
+unsigned int has_gmac() +{
- return !cpu_is_sama5d31();
+}
+unsigned int has_lcdc() +{
- return !cpu_is_sama5d35();
+}
+char *get_cpu_name() +{
- unsigned int extension_id = get_extension_chip_id();
- if (cpu_is_sama5d3())
switch (extension_id) {case ARCH_EXID_SAMA5D31:return CONFIG_SYS_AT91_D31_CPU_NAME;case ARCH_EXID_SAMA5D33:return CONFIG_SYS_AT91_D33_CPU_NAME;case ARCH_EXID_SAMA5D34:return CONFIG_SYS_AT91_D34_CPU_NAME;case ARCH_EXID_SAMA5D35:return CONFIG_SYS_AT91_D35_CPU_NAME;
As Tom mentioned I also think using the string here directly is a better solution. We should consider changing sam9x5 also.
default:return CONFIG_SYS_AT91_UNKNOWN_CPU;}- else
return CONFIG_SYS_AT91_UNKNOWN_CPU;+}
+void at91_serial0_hw_init(void) +{
- at91_set_a_periph(AT91_PIO_PORTD, 18, 1); /* TXD0 */
Why enabling PUP here for TX ...
- at91_set_a_periph(AT91_PIO_PORTD, 17, PUP); /* RXD0 */
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_USART0);
+}
+void at91_serial1_hw_init(void) +{
- at91_set_a_periph(AT91_PIO_PORTB, 28, 0); /* TXD1 */
... but not here?
- at91_set_a_periph(AT91_PIO_PORTB, 29, PUP); /* RXD1 */
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_USART1);
+}
+void at91_serial2_hw_init(void) +{
- at91_set_b_periph(AT91_PIO_PORTE, 26, 1); /* TXD2 */
- at91_set_b_periph(AT91_PIO_PORTE, 25, PUP); /* RXD2 */
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_USART2);
+}
+void at91_seriald_hw_init(void) +{
- at91_set_a_periph(AT91_PIO_PORTB, 30, 0); /* DRXD */
- at91_set_a_periph(AT91_PIO_PORTB, 31, 1); /* DTXD */
Can you swap the both lines before? There is always TX before RX but the DBGU is an exception ... please change. Shouldn't the DRXD also have PUP conditionally as the other RX lines have?
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_SYS);
+}
+#if defined(CONFIG_ATMEL_SPI) +void at91_spi0_hw_init(unsigned long cs_mask) +{
- at91_set_a_periph(AT91_PIO_PORTD, 10, 0); /* SPI0_MISO */
- at91_set_a_periph(AT91_PIO_PORTD, 11, 0); /* SPI0_MOSI */
- at91_set_a_periph(AT91_PIO_PORTD, 12, 0); /* SPI0_SPCK */
- if (cs_mask & (1 << 0))
at91_set_pio_output(AT91_PIO_PORTD, 13, 0);- if (cs_mask & (1 << 1))
at91_set_pio_output(AT91_PIO_PORTD, 14, 0);- if (cs_mask & (1 << 2))
at91_set_pio_output(AT91_PIO_PORTD, 15, 0);- if (cs_mask & (1 << 3))
at91_set_pio_output(AT91_PIO_PORTD, 16, 0);
PUP for the PIO's? The comment above states 'Good to have if hardware is soldered optionally or in case of SPI no slave is selected.' ...
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_SPI0);
+} +#endif
+#ifdef CONFIG_GENERIC_ATMEL_MCI +void at91_mci_hw_init(void) +{
- at91_set_pio_output(AT91_PIO_PORTB, 10, 0); /* MCI0 Power */
Well, this is board specific, isn't it? Should move to the board code.
- at91_set_a_periph(AT91_PIO_PORTD, 0, 0); /* MCI0 CMD */
- at91_set_a_periph(AT91_PIO_PORTD, 1, 0); /* MCI0 DA0 */
- at91_set_a_periph(AT91_PIO_PORTD, 2, 0); /* MCI0 DA1 */
- at91_set_a_periph(AT91_PIO_PORTD, 3, 0); /* MCI0 DA2 */
- at91_set_a_periph(AT91_PIO_PORTD, 4, 0); /* MCI0 DA3 */
+#ifdef CONFIG_ATMEL_MCI_8BIT
- at91_set_a_periph(AT91_PIO_PORTD, 5, 0); /* MCI0 DA4 */
- at91_set_a_periph(AT91_PIO_PORTD, 6, 0); /* MCI0 DA5 */
- at91_set_a_periph(AT91_PIO_PORTD, 7, 0); /* MCI0 DA6 */
- at91_set_a_periph(AT91_PIO_PORTD, 8, 0); /* MCI0 DA7 */
+#endif
- at91_set_a_periph(AT91_PIO_PORTD, 9, 0); /* MCI0 CLK */
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_MCI0);
+} +#endif
+#ifdef CONFIG_MACB +void at91_macb_hw_init(void) +{
- at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* ETXCK_EREFCK */
- at91_set_a_periph(AT91_PIO_PORTC, 5, 0); /* ERXDV */
- at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* ERX0 */
- at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* ERX1 */
- at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* ERXER */
- at91_set_a_periph(AT91_PIO_PORTC, 4, 0); /* ETXEN */
- at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* ETX0 */
- at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* ETX1 */
- at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* EMDIO */
- at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* EMDC */
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_EMAC);
+} +#endif
+#ifdef CONFIG_LCD +void at91_lcd_hw_init(void) +{
Can you place an hint here, that this currently supports only wireing of LCDDx on PORTA up to 16 bit? Or something like 'only sama5d3x board style currently imlemented'.
- at91_set_a_periph(AT91_PIO_PORTA, 24, 0); /* LCDPWM */
- at91_set_a_periph(AT91_PIO_PORTA, 25, 0); /* LCDDISP */
- at91_set_a_periph(AT91_PIO_PORTA, 26, 0); /* LCDVSYNC */
- at91_set_a_periph(AT91_PIO_PORTA, 27, 0); /* LCDHSYNC */
- at91_set_a_periph(AT91_PIO_PORTA, 28, 0); /* LCDDOTCK */
- at91_set_a_periph(AT91_PIO_PORTA, 29, 0); /* LCDDEN */
- at91_set_a_periph(AT91_PIO_PORTA, 0, 0); /* LCDD0 */
- at91_set_a_periph(AT91_PIO_PORTA, 1, 0); /* LCDD1 */
- at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* LCDD2 */
- at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* LCDD3 */
- at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* LCDD4 */
- at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* LCDD5 */
- at91_set_a_periph(AT91_PIO_PORTA, 6, 0); /* LCDD6 */
- at91_set_a_periph(AT91_PIO_PORTA, 7, 0); /* LCDD7 */
- at91_set_a_periph(AT91_PIO_PORTA, 8, 0); /* LCDD8 */
- at91_set_a_periph(AT91_PIO_PORTA, 9, 0); /* LCDD9 */
- at91_set_a_periph(AT91_PIO_PORTA, 10, 0); /* LCDD10 */
- at91_set_a_periph(AT91_PIO_PORTA, 11, 0); /* LCDD11 */
- at91_set_a_periph(AT91_PIO_PORTA, 12, 0); /* LCDD12 */
- at91_set_a_periph(AT91_PIO_PORTA, 13, 0); /* LCDD13 */
- at91_set_a_periph(AT91_PIO_PORTA, 14, 0); /* LCDD14 */
- at91_set_a_periph(AT91_PIO_PORTA, 15, 0); /* LCDD15 */
- at91_set_c_periph(AT91_PIO_PORTC, 14, 0); /* LCDD16 */
- at91_set_c_periph(AT91_PIO_PORTC, 13, 0); /* LCDD17 */
- at91_set_c_periph(AT91_PIO_PORTC, 12, 0); /* LCDD18 */
- at91_set_c_periph(AT91_PIO_PORTC, 11, 0); /* LCDD19 */
- at91_set_c_periph(AT91_PIO_PORTC, 10, 0); /* LCDD20 */
- at91_set_c_periph(AT91_PIO_PORTC, 15, 0); /* LCDD21 */
- at91_set_c_periph(AT91_PIO_PORTE, 27, 0); /* LCDD22 */
- at91_set_c_periph(AT91_PIO_PORTE, 28, 0); /* LCDD23 */
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_LCDC);
+} +#endif diff --git a/arch/arm/cpu/armv7/at91/timer.c b/arch/arm/cpu/armv7/at91/timer.c new file mode 100644 index 0000000..417326b --- /dev/null +++ b/arch/arm/cpu/armv7/at91/timer.c @@ -0,0 +1,136 @@ +/*
- (C) Copyright 2007-2008
- Stelian Pop stelian@popies.net
- Lead Tech Design <www.leadtechdesign.com>
your copyright?
- See file CREDITS for list of people who contributed to this
- project.
- This program is free software; you can redistribute it and/or
- modify it under the terms of the GNU General Public License as
- published by the Free Software Foundation; either version 2 of
- the License, or (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- MA 02111-1307 USA
- */
+#include <common.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/at91_pit.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> +#include <div64.h>
+#if !defined(CONFIG_AT91FAMILY) +# error You need to define CONFIG_AT91FAMILY in your board config! +#endif
+DECLARE_GLOBAL_DATA_PTR;
+/*
- We're using the AT91CAP9/SAM9 PITC in 32 bit mode, by
Is this comment unchanged correct? It is a sama5 SoC.
- setting the 20 bit counter period to its maximum (0xfffff).
- (See the relevant data sheets to understand that this really works)
- We do also mimic the typical powerpc way of incrementing
- two 32 bit registers called tbl and tbu.
- Those registers increment at 1/16 the main clock rate.
- */
+#define TIMER_LOAD_VAL 0xfffff
+static inline unsigned long long tick_to_time(unsigned long long tick) +{
- tick *= CONFIG_SYS_HZ;
- do_div(tick, gd->arch.timer_rate_hz);
- return tick;
+}
+static inline unsigned long long usec_to_tick(unsigned long long usec) +{
- usec *= gd->arch.timer_rate_hz;
- do_div(usec, 1000000);
- return usec;
+}
+/*
- Use the PITC in full 32 bit incrementing mode
- */
+int timer_init(void) +{
- at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC;
- at91_pit_t *pit = (at91_pit_t *)ATMEL_BASE_PIT;
- /* Enable PITC Clock */
- writel(1 << ATMEL_ID_SYS, &pmc->pcer);
at91_periph_clk_enable(ATMEL_ID_SYS);
- /* Enable PITC */
- writel(TIMER_LOAD_VAL | AT91_PIT_MR_EN , &pit->mr);
- gd->arch.timer_rate_hz = gd->arch.mck_rate_hz / 16;
- gd->arch.tbu = gd->arch.tbl = 0;
- return 0;
+}
+/*
- Get the current 64 bit timer tick count
- */
+unsigned long long get_ticks(void) +{
- at91_pit_t *pit = (at91_pit_t *)ATMEL_BASE_PIT;
- ulong now = readl(&pit->piir);
- /* increment tbu if tbl has rolled over */
- if (now < gd->arch.tbl)
gd->arch.tbu++;- gd->arch.tbl = now;
- return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;
+}
+void __udelay(unsigned long usec) +{
- unsigned long long start;
- ulong tmo;
- start = get_ticks(); /* get current timestamp */
- tmo = usec_to_tick(usec); /* convert usecs to ticks */
- while ((get_ticks() - start) < tmo)
; /* loop till time has passed */+}
+/*
- get_timer(base) can be used to check for timeouts or
- to measure elasped time relative to an event:
- ulong start_time = get_timer(0) sets start_time to the current
- time value.
- get_timer(start_time) returns the time elapsed since then.
- The time is used in CONFIG_SYS_HZ units!
- */
+ulong get_timer(ulong base) +{
- return tick_to_time(get_ticks()) - base;
+}
+/*
- Return the number of timer ticks per second.
- */
+ulong get_tbclk(void) +{
- return gd->arch.timer_rate_hz;
+} diff --git a/arch/arm/include/asm/arch-at91/at91_dbu.h b/arch/arm/include/asm/arch-at91/at91_dbu.h index 3429293..9a640a5 100644 --- a/arch/arm/include/asm/arch-at91/at91_dbu.h +++ b/arch/arm/include/asm/arch-at91/at91_dbu.h @@ -38,4 +38,8 @@ typedef struct at91_dbu { #define AT91_DBU_CID_ARCH_9xx 0x01900000 #define AT91_DBU_CID_ARCH_9XExx 0x02900000
+#define AT91_DBU_CIDR_MASK 0x1f +#define AT91_DBU_CIDR 0x40 +#define AT91_DBU_EXID 0x44
#endif diff --git a/arch/arm/include/asm/arch-at91/at91_pmc.h b/arch/arm/include/asm/arch-at91/at91_pmc.h index 086cb9b..198870f 100644 --- a/arch/arm/include/asm/arch-at91/at91_pmc.h +++ b/arch/arm/include/asm/arch-at91/at91_pmc.h @@ -55,7 +55,12 @@ typedef struct at91_pmc { u32 reserved5[21]; u32 wpmr; /* 0xE4 Write Protect Mode Register (CAP0) */ u32 wpsr; /* 0xE8 Write Protect Status Register (CAP0) */
- u32 reserved8[5];
- u32 reserved6[8];
- u32 pcer1; /* 0x100 Periperial Clock Enable Register 1 */
- u32 pcdr1; /* 0x104 Periperial Clock Disable Register 1 */
- u32 pcsr1; /* 0x108 Periperial Clock Status Register 1 */
- u32 pcr; /* 0x10c Periperial Control Register 1 */
- u32 ocr; /* 0x110 Oscillator Calibration Register 1 */
Shouldn't we hide these new entries to avoid cruical runtime errors? How about adding access to pmc->ocr to some at91 peripherial driver and miss to disable it for sam9 devices there? The compiler will not barf but on runtime we will get some access errors or 'undefined behaviour'.
} at91_pmc_t;
#endif /* end not assembly */ diff --git a/arch/arm/include/asm/arch-at91/clk.h b/arch/arm/include/asm/arch-at91/clk.h index d4852a3..04b0f83 100644 --- a/arch/arm/include/asm/arch-at91/clk.h +++ b/arch/arm/include/asm/arch-at91/clk.h @@ -95,4 +95,5 @@ static inline unsigned long get_mci_clk_rate(void) }
int at91_clock_init(unsigned long main_clock); +void at91_periph_clk_enable(int id); #endif /* __ASM_ARM_ARCH_CLK_H__ */ diff --git a/arch/arm/include/asm/arch-at91/hardware.h b/arch/arm/include/asm/arch-at91/hardware.h index 4c4ee70..87dd20b 100644 --- a/arch/arm/include/asm/arch-at91/hardware.h +++ b/arch/arm/include/asm/arch-at91/hardware.h @@ -43,6 +43,8 @@ # include <asm/arch/at91cap9.h> #elif defined(CONFIG_AT91X40) # include <asm/arch/at91x40.h> +#elif defined(CONFIG_SAMA5D3) +# include <asm/arch/sama5d3.h> #else # error "Unsupported AT91 processor" #endif diff --git a/arch/arm/include/asm/arch-at91/sama5d3.h b/arch/arm/include/asm/arch-at91/sama5d3.h new file mode 100644 index 0000000..5538bf6 --- /dev/null +++ b/arch/arm/include/asm/arch-at91/sama5d3.h @@ -0,0 +1,220 @@ +/*
- Chip-specific header file for the SAMA5D3 family
- (C) 2012 Atmel Corporation.
your email?
- Definitions for the SoC:
- SAMA5D3
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation; either version 2 of the License, or
- (at your option) any later version.
- */
+#ifndef SAMA5D3_H +#define SAMA5D3_H
+/*
- defines to be used in other places
- */
+#define CONFIG_ARMV7 /* ARM A5 Core */ +#define CONFIG_AT91FAMILY /* it's a member of AT91 */
+/*
- Peripheral identifiers/interrupts.
- */
+#define ATMEL_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ +#define ATMEL_ID_SYS 1 /* System Controller Interrupt */ +#define ATMEL_ID_DBGU 2 /* Debug Unit Interrupt */ +#define ATMEL_ID_PIT 3 /* Periodic Interval Timer Interrupt */ +#define ATMEL_ID_WDT 4 /* Watchdog timer Interrupt */ +#define ATMEL_ID_SMC 5 /* Multi-bit ECC Interrupt */ +#define ATMEL_ID_PIOA 6 /* Parallel I/O Controller A */ +#define ATMEL_ID_PIOB 7 /* Parallel I/O Controller B */ +#define ATMEL_ID_PIOC 8 /* Parallel I/O Controller C */ +#define ATMEL_ID_PIOD 9 /* Parallel I/O Controller D */ +#define ATMEL_ID_PIOE 10 /* Parallel I/O Controller E */ +#define ATMEL_ID_SMD 11 /* SMD Soft Modem */ +#define ATMEL_ID_USART0 12 /* USART 0 */ +#define ATMEL_ID_USART1 13 /* USART 1 */ +#define ATMEL_ID_USART2 14 /* USART 2 */ +#define ATMEL_ID_USART3 15 /* USART 3 */ +#define ATMEL_ID_UART0 16 +#define ATMEL_ID_UART1 17 +#define ATMEL_ID_TWI0 18 /* Two-Wire Interface 0 */ +#define ATMEL_ID_TWI1 19 /* Two-Wire Interface 1 */ +#define ATMEL_ID_TWI2 20 /* Two-Wire Interface 2 */ +#define ATMEL_ID_MCI0 21 /* High Speed Multimedia Card Interface 0 */ +#define ATMEL_ID_MCI1 22 /* */ +#define ATMEL_ID_MCI2 23 /* */ +#define ATMEL_ID_SPI0 24 /* Serial Peripheral Interface 0 */ +#define ATMEL_ID_SPI1 25 /* Serial Peripheral Interface 1 */ +#define ATMEL_ID_TC0 26 /* */ +#define ATMEL_ID_TC1 27 /* */ +#define ATMEL_ID_PWMC 28 /* Pulse Width Modulation Controller */ +#define ATMEL_ID_TSC 29 /* Touch Screen ADC Controller */ +#define ATMEL_ID_DMA0 30 /* DMA Controller */ +#define ATMEL_ID_DMA1 31 /* DMA Controller */ +#define ATMEL_ID_UHPHS 32 /* USB Host High Speed */ +#define ATMEL_ID_UDPHS 33 /* USB Device High Speed */ +#define ATMEL_ID_GMAC 34 +#define ATMEL_ID_EMAC 35 /* Ethernet MAC */ +#define ATMEL_ID_LCDC 36 /* LCD Controller */ +#define ATMEL_ID_ISI 37 /* Image Sensor Interface */ +#define ATMEL_ID_SSC0 38 /* Synchronous Serial Controller 0 */ +#define ATMEL_ID_SSC1 39 /* Synchronous Serial Controller 1 */ +#define ATMEL_ID_CAN0 40 +#define ATMEL_ID_CAN1 41 +#define ATMEL_ID_SHA 42 +#define ATMEL_ID_AES 43 +#define ATMEL_ID_TDES 44 +#define ATMEL_ID_TRNG 45 +#define ATMEL_ID_ARM 46 +#define ATMEL_ID_IRQ0 47 /* Advanced Interrupt Controller */ +#define ATMEL_ID_FUSE 48 +#define ATMEL_ID_MPDDRC 49
+/* sama5d3 series chip id definitions */ +#define ARCH_ID_SAMA5D3 0x8a5c07c0 +#define ARCH_EXID_SAMA5D31 0x00444300 +#define ARCH_EXID_SAMA5D33 0x00414300 +#define ARCH_EXID_SAMA5D34 0x00414301 +#define ARCH_EXID_SAMA5D35 0x00584300
+#define cpu_is_sama5d3() (get_chip_id() == ARCH_ID_SAMA5D3) +#define cpu_is_sama5d31() (cpu_is_sama5d3() && \
(get_extension_chip_id() == ARCH_EXID_SAMA5D31))+#define cpu_is_sama5d33() (cpu_is_sama5d3() && \
(get_extension_chip_id() == ARCH_EXID_SAMA5D33))+#define cpu_is_sama5d34() (cpu_is_sama5d3() && \
(get_extension_chip_id() == ARCH_EXID_SAMA5D34))+#define cpu_is_sama5d35() (cpu_is_sama5d3() && \
(get_extension_chip_id() == ARCH_EXID_SAMA5D35))+/*
- User Peripherals physical base addresses.
- */
+#define ATMEL_BASE_MCI0 0xf0000000 +#define ATMEL_BASE_SPI0 0xf0004000 +#define ATMEL_BASE_SSC0 0xf000C000 +#define ATMEL_BASE_TC2 0xf0010000 +#define ATMEL_BASE_TWI0 0xf0014000 +#define ATMEL_BASE_TWI1 0xf0018000 +#define ATMEL_BASE_USART0 0xf001c000 +#define ATMEL_BASE_USART1 0xf0020000 +#define ATMEL_BASE_UART0 0xf0024000 +#define ATMEL_BASE_GMAC 0xf0028000 +#define ATMEL_BASE_PWMC 0xf002c000 +#define ATMEL_BASE_LCDC 0xf0030000 +#define ATMEL_BASE_ISI 0xf0034000 +#define ATMEL_BASE_SFR 0xf0038000 +/* Reserved: 0xf003c000 - 0xf8000000 */ +#define ATMEL_BASE_MCI1 0xf8000000 +#define ATMEL_BASE_MCI2 0xf8004000 +#define ATMEL_BASE_SPI1 0xf8008000 +#define ATMEL_BASE_SSC1 0xf800c000 +#define ATMEL_BASE_CAN1 0xf8010000 +#define ATMEL_BASE_TC3 0xf8014000 +#define ATMEL_BASE_TSADC 0xf8018000 +#define ATMEL_BASE_TWI2 0xf801c000 +#define ATMEL_BASE_USART2 0xf8020000 +#define ATMEL_BASE_USART3 0xf8024000 +#define ATMEL_BASE_UART1 0xf8028000 +#define ATMEL_BASE_EMAC 0xf802c000 +#define ATMEL_BASE_UDHPS 0xf8030000 +#define ATMEL_BASE_SHA 0xf8034000 +#define ATMEL_BASE_AES 0xf8038000 +#define ATMEL_BASE_TDES 0xf803c000 +#define ATMEL_BASE_TRNG 0xf8040000 +/* Reserved: 0xf804400 - 0xffffc00 */
+/*
- System Peripherals physical base addresses.
- */
+#define ATMEL_BASE_SYS 0xffffc000 +#define ATMEL_BASE_SMC 0xffffc000 +#define ATMEL_BASE_PMECC (ATMEL_BASE_SMC + 0x070) +#define ATMEL_BASE_PMERRLOC (ATMEL_BASE_SMC + 0x500) +#define ATMEL_BASE_FUSE 0xffffe400 +#define ATMEL_BASE_DMAC0 0xffffe600 +#define ATMEL_BASE_DMAC1 0xffffe800 +#define ATMEL_BASE_MPDDRC 0xffffea00 +#define ATMEL_BASE_MATRIX 0xffffec00 +#define ATMEL_BASE_DBGU 0xffffee00 +#define ATMEL_BASE_AIC 0xfffff000 +#define ATMEL_BASE_PIOA 0xfffff200 +#define ATMEL_BASE_PIOB 0xfffff400 +#define ATMEL_BASE_PIOC 0xfffff600 +#define ATMEL_BASE_PIOD 0xfffff800 +#define ATMEL_BASE_PIOE 0xfffffa00 +#define ATMEL_BASE_PMC 0xfffffc00 +#define ATMEL_BASE_RSTC 0xfffffe00 +#define ATMEL_BASE_SHDWN 0xfffffe10 +#define ATMEL_BASE_PIT 0xfffffe30 +#define ATMEL_BASE_WDT 0xfffffe40 +#define ATMEL_BASE_SCKCR 0xfffffe50 +#define ATMEL_BASE_GPBR 0xfffffe60 +#define ATMEL_BASE_RTC 0xfffffeb0 +/* Reserved: 0xfffffee0 - 0xffffffff */
+/*
- Internal Memory.
- */
+#define ATMEL_BASE_ROM 0x00100000 /* Internal ROM base address */ +#define ATMEL_BASE_SRAM 0x00200000 /* Internal ROM base address */ +#define ATMEL_BASE_SRAM0 0x00300000 /* Internal SRAM base address */ +#define ATMEL_BASE_SRAM1 0x00310000 /* Internal SRAM base address */ +#define ATMEL_BASE_SMD 0x00400000 /* Internal ROM base address */ +#define ATMEL_BASE_UDPHS_FIFO 0x00500000 /* USB Device HS controller */ +#define ATMEL_BASE_OHCI 0x00600000 /* USB Host controller (OHCI) */ +#define ATMEL_BASE_EHCI 0x00700000 /* USB Host controller (EHCI) */ +#define ATMEL_BASE_AXI 0x00800000 /* Video Decoder Controller */ +#define ATMEL_BASE_DAP 0x00900000 /* Video Decoder Controller */
+/*
- External memory
- */
+#define ATMEL_BASE_CS0 0x10000000 +#define ATMEL_BASE_DDRCS 0x20000000 +#define ATMEL_BASE_CS1 0x40000000 +#define ATMEL_BASE_CS2 0x50000000 +#define ATMEL_BASE_CS3 0x60000000
+/*
- Other misc defines
- */
+#define ATMEL_PIO_PORTS 5 +#define CPU_HAS_PIO3 +#define PIO_SCDR_DIV 0x3fff
+/*
- PMECC table in ROM
- */
+#define ATMEL_PMECC_INDEX_OFFSET_512 0x10000 +#define ATMEL_PMECC_INDEX_OFFSET_1024 0x18000 +#define ATMEL_PMECC_ALPHA_OFFSET_512 0x10000 +#define ATMEL_PMECC_ALPHA_OFFSET_1024 0x18000
+/*
- Cpu Name
- */
+#define CONFIG_SYS_AT91_D31_CPU_NAME "SAMA5D31" +#define CONFIG_SYS_AT91_D33_CPU_NAME "SAMA5D33" +#define CONFIG_SYS_AT91_D34_CPU_NAME "SAMA5D34" +#define CONFIG_SYS_AT91_D35_CPU_NAME "SAMA5D35" +#define CONFIG_SYS_AT91_UNKNOWN_CPU "Unknown CPU type"
+/*
- SAMA5D3 specific prototypes
- */
+#ifndef __ASSEMBLY__ +unsigned int get_chip_id(void); +unsigned int get_extension_chip_id(void); +unsigned int has_emac(void); +unsigned int has_gmac(void); +unsigned int has_lcdc(void); +char *get_cpu_name(void); +#endif
+#endif diff --git a/arch/arm/include/asm/arch-at91/sama5d3_smc.h b/arch/arm/include/asm/arch-at91/sama5d3_smc.h new file mode 100644 index 0000000..eb53eba --- /dev/null +++ b/arch/arm/include/asm/arch-at91/sama5d3_smc.h @@ -0,0 +1,79 @@ +/*
- Copyright (C) 2012 Atmel Corporation.
- Static Memory Controllers (SMC) - System peripherals registers.
- Based on SAMA5D3 datasheet.
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation; either version 2 of the License, or
- (at your option) any later version.
- */
+#ifndef SAMA5D3_SMC_H +#define SAMA5D3_SMC_H
+#ifdef __ASSEMBLY__ +#define AT91_ASM_SMC_SETUP0 (ATMEL_BASE_SMC + 0x600) +#define AT91_ASM_SMC_PULSE0 (ATMEL_BASE_SMC + 0x604) +#define AT91_ASM_SMC_CYCLE0 (ATMEL_BASE_SMC + 0x608) +#define AT91_ASM_SMC_MODE0 (ATMEL_BASE_SMC + 0x60C) +#else +struct at91_cs {
- u32 reserved[96];
- u32 setup; /* 0x600 SMC Setup Register */
- u32 pulse; /* 0x604 SMC Pulse Register */
- u32 cycle; /* 0x608 SMC Cycle Register */
- u32 timings; /* 0x60C SMC Cycle Register */
- u32 mode; /* 0x610 SMC Mode Register */
+};
+struct at91_smc {
- struct at91_cs cs[4];
+}; +#endif /* __ASSEMBLY__ */
+#define AT91_SMC_SETUP_NWE(x) (x & 0x3f) +#define AT91_SMC_SETUP_NCS_WR(x) ((x & 0x3f) << 8) +#define AT91_SMC_SETUP_NRD(x) ((x & 0x3f) << 16) +#define AT91_SMC_SETUP_NCS_RD(x) ((x & 0x3f) << 24)
+#define AT91_SMC_PULSE_NWE(x) (x & 0x3f) +#define AT91_SMC_PULSE_NCS_WR(x) ((x & 0x3f) << 8) +#define AT91_SMC_PULSE_NRD(x) ((x & 0x3f) << 16) +#define AT91_SMC_PULSE_NCS_RD(x) ((x & 0x3f) << 24)
+#define AT91_SMC_CYCLE_NWE(x) (x & 0x1ff) +#define AT91_SMC_CYCLE_NRD(x) ((x & 0x1ff) << 16)
+#define AT91_SMC_TIMINGS_TCLR(x) (x & 0xf) +#define AT91_SMC_TIMINGS_TADL(x) ((x & 0xf) << 4) +#define AT91_SMC_TIMINGS_TAR(x) ((x & 0xf) << 8) +#define AT91_SMC_TIMINGS_OCMS(x) ((x & 0x1) << 12) +#define AT91_SMC_TIMINGS_TRR(x) ((x & 0xf) << 16) +#define AT91_SMC_TIMINGS_TWB(x) ((x & 0xf) << 24) +#define AT91_SMC_TIMINGS_RBNSEL(x) ((x & 0xf) << 28) +#define AT91_SMC_TIMINGS_NFSEL(x) ((x & 0x1) << 31)
+#define AT91_SMC_MODE_RM_NCS 0x00000000 +#define AT91_SMC_MODE_RM_NRD 0x00000001 +#define AT91_SMC_MODE_WM_NCS 0x00000000 +#define AT91_SMC_MODE_WM_NWE 0x00000002
+#define AT91_SMC_MODE_EXNW_DISABLE 0x00000000 +#define AT91_SMC_MODE_EXNW_FROZEN 0x00000020 +#define AT91_SMC_MODE_EXNW_READY 0x00000030
+#define AT91_SMC_MODE_BAT 0x00000100 +#define AT91_SMC_MODE_DBW_8 0x00000000 +#define AT91_SMC_MODE_DBW_16 0x00001000 +#define AT91_SMC_MODE_DBW_32 0x00002000 +#define AT91_SMC_MODE_TDF_CYCLE(x) ((x & 0xf) << 16) +#define AT91_SMC_MODE_TDF 0x00100000 +#define AT91_SMC_MODE_PMEN 0x01000000 +#define AT91_SMC_MODE_PS_4 0x00000000 +#define AT91_SMC_MODE_PS_8 0x10000000 +#define AT91_SMC_MODE_PS_16 0x20000000 +#define AT91_SMC_MODE_PS_32 0x30000000
+#endif diff --git a/board/atmel/sama5d3xek/Makefile b/board/atmel/sama5d3xek/Makefile new file mode 100644 index 0000000..357bb7c --- /dev/null +++ b/board/atmel/sama5d3xek/Makefile @@ -0,0 +1,48 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# (C) Copyright 2008 +# Stelian Pop stelian@popies.net +# Lead Tech Design <www.leadtechdesign.com>
your copyright?
+# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +#
+include $(TOPDIR)/config.mk
+LIB = $(obj)lib$(BOARD).o
+COBJS-y += sama5d3xek.o
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS))
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+#########################################################################
+# defines $(obj).depend target +include $(SRCTREE)/rules.mk
+sinclude $(obj).depend
+######################################################################### diff --git a/board/atmel/sama5d3xek/sama5d3xek.c b/board/atmel/sama5d3xek/sama5d3xek.c new file mode 100644 index 0000000..352d20c --- /dev/null +++ b/board/atmel/sama5d3xek/sama5d3xek.c @@ -0,0 +1,274 @@ +/*
- Copyright (C) 2012 - 2013 Atmel Corporation
your email?
- See file CREDITS for list of people who contributed to this
- project.
- This program is free software; you can redistribute it and/or
- modify it under the terms of the GNU General Public License as
- published by the Free Software Foundation; either version 2 of
- the License, or (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- MA 02111-1307 USA
- */
+#include <common.h> +#include <mmc.h> +#include <asm/io.h> +#include <asm/arch/sama5d3_smc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/clk.h> +#include <lcd.h> +#include <atmel_lcdc.h> +#include <atmel_mci.h> +#include <net.h> +#include <netdev.h>
+DECLARE_GLOBAL_DATA_PTR;
+/* ------------------------------------------------------------------------- */ +/*
- Miscelaneous platform dependent initialisations
- */
+#ifdef CONFIG_CMD_NAND +void sama5d3xek_nand_hw_init(void) +{
- struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
- at91_periph_clk_enable(ATMEL_ID_SMC);
- /* Configure SMC CS3 for NAND/SmartMedia */
- writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(1) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(1),&smc->cs[3].setup);- writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(5),&smc->cs[3].pulse);- writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8),
&smc->cs[3].cycle);- writel(AT91_SMC_TIMINGS_TCLR(3) | AT91_SMC_TIMINGS_TADL(10) |
AT91_SMC_TIMINGS_TAR(3) | AT91_SMC_TIMINGS_TRR(4) |AT91_SMC_TIMINGS_TWB(5) | AT91_SMC_TIMINGS_RBNSEL(3)|AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);- writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |+#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |+#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |+#endif
AT91_SMC_MODE_TDF_CYCLE(3),&smc->cs[3].mode);+} +#endif
+#ifdef CONFIG_CMD_USB +static void sama5d3xek_usb_hw_init(void) +{
- at91_set_pio_output(AT91_PIO_PORTD, 25, 0);
- at91_set_pio_output(AT91_PIO_PORTD, 26, 0);
- at91_set_pio_output(AT91_PIO_PORTD, 27, 0);
+} +#endif
Isn't the usb stuff generic? Shouldn't we move it to sama5d3_devices.c?
+#ifdef CONFIG_GENERIC_ATMEL_MCI +static void sama5d3xek_mci_hw_init(void) +{
place here the power gpio thing for this board.
- at91_mci_hw_init();
+} +#endif
+#ifdef CONFIG_MACB +static void sama5d3xek_macb_hw_init(void) +{
remove this function and move the at91_macb_hw_init() down to board_init().
- at91_macb_hw_init();
+} +#endif
+#ifdef CONFIG_LCD +vidinfo_t panel_info = {
- .vl_col = 800,
- .vl_row = 480,
- .vl_clk = 24000000,
- .vl_sync = ATMEL_LCDC_INVLINE_NORMAL | ATMEL_LCDC_INVFRAME_NORMAL,
- .vl_bpix = LCD_BPP,
- .vl_tft = 1,
- .vl_hsync_len = 128,
- .vl_left_margin = 64,
- .vl_right_margin = 64,
- .vl_vsync_len = 2,
- .vl_upper_margin = 22,
- .vl_lower_margin = 21,
- .mmio = ATMEL_BASE_LCDC,
+};
+void lcd_enable(void) +{
- at91_set_a_periph(AT91_PIO_PORTA, 29, 1); /* power up */
+}
+void lcd_disable(void) +{
The PA29 is handed to the LCD IP in at91_lcd_hw_init(), isn't there some register to switch the power on and off? Why using the pullup for this purpose here?
- at91_set_a_periph(AT91_PIO_PORTA, 29, 0); /* power down */
+}
+static void sama5d3xek_lcd_hw_init(void) +{
- gd->fb_base = CONFIG_SAMA5D3_LCD_BASE;
- at91_lcd_hw_init();
+}
+#ifdef CONFIG_LCD_INFO +#include <nand.h> +#include <version.h>
+void lcd_show_board_info(void)
This function is really subject to move to a arch/arm/lib/at91 ... We should think about that.
+{
- ulong dram_size, nand_size;
- int i;
- char temp[32];
- lcd_printf("%s\n", U_BOOT_VERSION);
- lcd_printf("(C) 2012 ATMEL Corp\n");
We have 2013 ;)
- lcd_printf("at91support@atmel.com\n");
- lcd_printf("%s CPU at %s MHz\n",
get_cpu_name(),strmhz(temp, get_cpu_clk_rate()));- dram_size = 0;
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
dram_size += gd->bd->bi_dram[i].size;- nand_size = 0;
+#ifdef CONFIG_CMD_NAND
- for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
nand_size += nand_info[i].size;+#endif
- lcd_printf(" %ld MB SDRAM, %ld MB NAND\n",
dram_size >> 20,nand_size >> 20);+} +#endif /* CONFIG_LCD_INFO */ +#endif /* CONFIG_LCD */
+int board_early_init_f(void) +{
- at91_seriald_hw_init();
- return 0;
+}
+int board_init(void) +{
- /* Enable Ctrlc */
- console_init_f();
Please remove that, it is still called by board_init_f() which runs way before board_init() which is called in board_init_r()!
- /* adress of boot parameters */
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+#ifdef CONFIG_CMD_NAND
Should this really depend on the nand commands?
- sama5d3xek_nand_hw_init();
+#endif +#ifdef CONFIG_CMD_USB
- sama5d3xek_usb_hw_init();
+#endif +#ifdef CONFIG_GENERIC_ATMEL_MCI
- sama5d3xek_mci_hw_init();
+#endif +#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 0);
+#endif +#ifdef CONFIG_MACB
- if (has_emac())
sama5d3xek_macb_hw_init();+#endif +#ifdef CONFIG_LCD
- if (has_lcdc())
sama5d3xek_lcd_hw_init();+#endif
- return 0;
+}
+int dram_init(void) +{
- gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);- return 0;
+}
+int board_eth_init(bd_t *bis) +{
- int rc = 0;
+#ifdef CONFIG_MACB
- if (has_emac())
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);+#endif
- return rc;
+}
+#ifdef CONFIG_GENERIC_ATMEL_MCI +int board_mmc_init(bd_t *bis) +{
- int rc = 0;
- rc = atmel_mci_init((void *)ATMEL_BASE_MCI0);
- return rc;
+} +#endif
+/* SPI chip select control */ +#ifdef CONFIG_ATMEL_SPI +#include <spi.h>
+int spi_cs_is_valid(unsigned int bus, unsigned int cs) +{
- return bus == 0 && cs < 4;
+}
+void spi_cs_activate(struct spi_slave *slave) +{
- switch (slave->cs) {
- case 0:
at91_set_pio_output(AT91_PIO_PORTD, 13, 0);- case 1:
at91_set_pio_output(AT91_PIO_PORTD, 14, 0);- case 2:
at91_set_pio_output(AT91_PIO_PORTD, 15, 0);- case 3:
at91_set_pio_output(AT91_PIO_PORTD, 16, 0);- default:
break;- }
+}
+void spi_cs_deactivate(struct spi_slave *slave) +{
- switch (slave->cs) {
- case 0:
at91_set_pio_output(AT91_PIO_PORTD, 13, 1);- case 1:
at91_set_pio_output(AT91_PIO_PORTD, 14, 1);- case 2:
at91_set_pio_output(AT91_PIO_PORTD, 15, 1);- case 3:
at91_set_pio_output(AT91_PIO_PORTD, 16, 1);- default:
break;- }
+} +#endif /* CONFIG_ATMEL_SPI */ diff --git a/boards.cfg b/boards.cfg index 32b0ccf..962a3e9 100644 --- a/boards.cfg +++ b/boards.cfg @@ -240,6 +240,9 @@ am335x_evm_uart3 arm armv7 am335x ti am335x_evm_uart4 arm armv7 am335x ti am33xx am335x_evm:SERIAL5,CONS_INDEX=5 am335x_evm_uart5 arm armv7 am335x ti am33xx am335x_evm:SERIAL6,CONS_INDEX=6 pcm051 arm armv7 pcm051 phytec am33xx pcm051 +sama5d3xek_nandflash arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_NANDFLASH +sama5d3xek_sdcard arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_MMC +sama5d3xek_spiflash arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_SERIALFLASH highbank arm armv7 highbank - highbank mx51_efikamx arm armv7 mx51_efikamx genesi mx5 mx51_efikamx:MACH_TYPE=MACH_TYPE_MX51_EFIKAMX,IMX_CONFIG=board/genesi/mx51_efikamx/imximage_mx.cfg mx51_efikasb arm armv7 mx51_efikamx genesi mx5 mx51_efikamx:MACH_TYPE=MACH_TYPE_MX51_EFIKASB,IMX_CONFIG=board/genesi/mx51_efikamx/imximage_sb.cfg diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h new file mode 100644 index 0000000..63616d0 --- /dev/null +++ b/include/configs/sama5d3xek.h @@ -0,0 +1,268 @@ +/*
- Configuation settings for the SAMA5D3xEK board.
- Copyright (C) 2012 - 2013 Atmel
your email?
- based on at91sam9m10g45ek.h by:
- Stelian Pop stelian@popies.net
- Lead Tech Design <www.leadtechdesign.com>
- See file CREDITS for list of people who contributed to this
- project.
- This program is free software; you can redistribute it and/or
- modify it under the terms of the GNU General Public License as
- published by the Free Software Foundation; either version 2 of
- the License, or (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- MA 02111-1307 USA
- */
+#ifndef __CONFIG_H +#define __CONFIG_H
+#include <asm/hardware.h>
+#define CONFIG_SYS_TEXT_BASE 0x26f00000
+/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ +#define CONFIG_SYS_HZ 1000
+#define CONFIG_AT91FAMILY +#define CONFIG_ARCH_CPU_INIT +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
As mentioned before, please do not undef what was never defined before.
+#undef CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#undef CONFIG_SETUP_MEMORY_TAGS +#undef CONFIG_INITRD_TAG +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_CMD_BOOTZ +#define CONFIG_OF_LIBFDT /* Device Tree support */
+/* general purpose I/O */ +#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
grrr ... we really _should_ fix it some day.
+#define CONFIG_AT91_GPIO +#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
+/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_DBGU
+/*
- This needs to be defined for the OHCI code to work but it is defined as
- ATMEL_ID_UHPHS in the CPU specific header files.
- */
+#define ATMEL_ID_UHP ATMEL_ID_UHPHS
+/*
- Specify the clock enable bit in the PMC_SCER register.
- */
+#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
Is this define still correctly named?
+/* LCD */ +#define CONFIG_LCD +#define LCD_BPP LCD_COLOR16 +#define LCD_OUTPUT_BPP 24 +#define CONFIG_LCD_LOGO +#undef LCD_TEST_PATTERN +#define CONFIG_LCD_INFO +#define CONFIG_LCD_INFO_BELOW_LOGO +#define CONFIG_SYS_WHITE_ON_BLACK +#define CONFIG_ATMEL_HLCD +#define CONFIG_ATMEL_LCD_RGB565 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+/* board specific(not enough SRAM) */ +#define CONFIG_SAMA5D3_LCD_BASE 0x23E00000
+#define CONFIG_BOOTDELAY 3
+/*
- BOOTP options
- */
+#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME
+/*
- Command line configuration.
- */
+#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_IMLS
IMLS is useful, consider leaving it in.
+#undef CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_LOADS
+#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP
+/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS +#define CONFIG_SYS_SDRAM_SIZE 0x20000000
+#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+/* SerialFlash */ +#define CONFIG_CMD_SF
+#ifdef CONFIG_CMD_SF +#define CONFIG_ATMEL_SPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#endif
+/* No NOR flash */ +#define CONFIG_SYS_NO_FLASH
+/* NAND flash */ +#define CONFIG_CMD_NAND
+#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_MAX_CHIPS 1 +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +#define CONFIG_SYS_NAND_DBW_8 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ONFI_DETECTION +/* PMECC & PMERRLOC */ +#define CONFIG_ATMEL_NAND_HWECC +#define CONFIG_ATMEL_NAND_HW_PMECC +#define CONFIG_PMECC_CAP 4 +#define CONFIG_PMECC_SECTOR_SIZE 512 +#define CONFIG_PMECC_INDEX_TABLE_OFFSET ATMEL_PMECC_INDEX_OFFSET_512 +#define CONFIG_CMD_NAND_TRIMFFS +#endif
+/* Ethernet Hardware */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_MULTI +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_MACB_SEARCH_PHY
+/* MMC */ +#define CONFIG_CMD_MMC
+#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#define ATMEL_BASE_MMCI ATMEL_BASE_MCI0 +#endif
+/* USB */ +#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "sama5d3" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3 +#define CONFIG_DOS_PARTITION +#define CONFIG_USB_STORAGE +#endif
+#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) +#define CONFIG_CMD_FAT +#endif
+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END 0x23e00000
Please re-think sizes in non-volatile memory. They should be sane and let some space for future growing of images.
+#ifdef CONFIG_SYS_USE_SERIALFLASH +/* bootstrap + u-boot + env + linux in serial flash */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_SYS_MONITOR_BASE (0x10000000 + 0x8400) +#define CONFIG_ENV_OFFSET 0x5000 +#define CONFIG_ENV_ADDR (0x10000000 + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x3000 +#define CONFIG_ENV_SECT_SIZE 0x1000 +#define CONFIG_BOOTCOMMAND "sf probe 0; " \
"sf read 0x22000000 0x42000 0x300000; " \"bootm 0x22000000"+#elif CONFIG_SYS_USE_NANDFLASH +/* bootstrap + u-boot + env in nandflash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0xc0000 +#define CONFIG_ENV_OFFSET_REDUND 0x100000 +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \
"nand read 0x22000000 0x200000 0x600000;" \"bootm 0x22000000 - 0x21000000"+#elif CONFIG_SYS_USE_MMC +/* bootstrap + u-boot + env in sd card */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET 0x2000 +#define CONFIG_ENV_OFFSET_REDUND 0x4000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_BOOTCOMMAND "mmcinfo;fatload mmc 0:1 0x21000000 dtb;" \
"fatload mmc 0:1 0x22000000 uImage;" \"bootm 0x22000000 - 0x21000000"+#define CONFIG_SYS_MMC_ENV_DEV 0 +#else +#define CONIG_ENV_IS_NOWHERE +#endif
+#ifdef CONFIG_SYS_USE_MMC +#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "root=/dev/mmcblk0p2 " \
- "rw rootfstype=ext2 rootdelay=2"
Consider using 'rootwait' rather than 'rootdelay' here.
+#else +#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
- "256K(env),256k(evn_redundent),256k(spare)," \
- "512k(dtb),6M(kernel)ro,-(rootfs) " \
sizes seems to be sane for me.
- "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
+#endif
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)+#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER
+/*
- Size of malloc() pool
- */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
+#ifdef CONFIG_USE_IRQ +#error CONFIG_USE_IRQ not supported +#endif
+#endif
Best regards
Andreas Bießmann