[PATCH 17/24] arm: Remove configs/T2080RDB_NAND_defconfig board

This board has not been converted to CONFIG_DM_SPI by the deadline.

Remove it.

Patch-cc: Shengzhou Liu Shengzhou.Liu@nxp.com Patch-cc: Ruchika Gupta ruchika.gupta@nxp.com Signed-off-by: Jagan Teki jagan@amarulasolutions.com --- arch/powerpc/cpu/mpc85xx/Kconfig | 1 - board/freescale/t208xrdb/Kconfig | 14 - board/freescale/t208xrdb/MAINTAINERS | 15 - board/freescale/t208xrdb/Makefile | 16 - board/freescale/t208xrdb/README | 283 -------- board/freescale/t208xrdb/cpld.c | 70 -- board/freescale/t208xrdb/cpld.h | 44 -- board/freescale/t208xrdb/ddr.c | 118 ---- board/freescale/t208xrdb/ddr.h | 46 -- board/freescale/t208xrdb/eth_t208xrdb.c | 107 --- board/freescale/t208xrdb/law.c | 33 - board/freescale/t208xrdb/pci.c | 25 - board/freescale/t208xrdb/spl.c | 112 --- board/freescale/t208xrdb/t2080_nand_rcw.cfg | 19 - board/freescale/t208xrdb/t2080_pbi.cfg | 40 -- board/freescale/t208xrdb/t2080_sd_rcw.cfg | 19 - board/freescale/t208xrdb/t2080_spi_rcw.cfg | 19 - board/freescale/t208xrdb/t208xrdb.c | 142 ---- board/freescale/t208xrdb/t208xrdb.h | 12 - board/freescale/t208xrdb/tlb.c | 152 ----- configs/T2080RDB_NAND_defconfig | 84 --- configs/T2080RDB_SDCARD_defconfig | 81 --- configs/T2080RDB_SECURE_BOOT_defconfig | 63 -- configs/T2080RDB_SPIFLASH_defconfig | 84 --- configs/T2080RDB_SRIO_PCIE_BOOT_defconfig | 53 -- configs/T2080RDB_defconfig | 68 -- include/configs/T208xRDB.h | 717 -------------------- 27 files changed, 2437 deletions(-) delete mode 100644 board/freescale/t208xrdb/Kconfig delete mode 100644 board/freescale/t208xrdb/MAINTAINERS delete mode 100644 board/freescale/t208xrdb/Makefile delete mode 100644 board/freescale/t208xrdb/README delete mode 100644 board/freescale/t208xrdb/cpld.c delete mode 100644 board/freescale/t208xrdb/cpld.h delete mode 100644 board/freescale/t208xrdb/ddr.c delete mode 100644 board/freescale/t208xrdb/ddr.h delete mode 100644 board/freescale/t208xrdb/eth_t208xrdb.c delete mode 100644 board/freescale/t208xrdb/law.c delete mode 100644 board/freescale/t208xrdb/pci.c delete mode 100644 board/freescale/t208xrdb/spl.c delete mode 100644 board/freescale/t208xrdb/t2080_nand_rcw.cfg delete mode 100644 board/freescale/t208xrdb/t2080_pbi.cfg delete mode 100644 board/freescale/t208xrdb/t2080_sd_rcw.cfg delete mode 100644 board/freescale/t208xrdb/t2080_spi_rcw.cfg delete mode 100644 board/freescale/t208xrdb/t208xrdb.c delete mode 100644 board/freescale/t208xrdb/t208xrdb.h delete mode 100644 board/freescale/t208xrdb/tlb.c delete mode 100644 configs/T2080RDB_NAND_defconfig delete mode 100644 configs/T2080RDB_SDCARD_defconfig delete mode 100644 configs/T2080RDB_SECURE_BOOT_defconfig delete mode 100644 configs/T2080RDB_SPIFLASH_defconfig delete mode 100644 configs/T2080RDB_SRIO_PCIE_BOOT_defconfig delete mode 100644 configs/T2080RDB_defconfig delete mode 100644 include/configs/T208xRDB.h

diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index edccf3698c..82c5a51f48 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -1599,7 +1599,6 @@ source "board/freescale/mpc8572ds/Kconfig" source "board/freescale/p1023rdb/Kconfig" source "board/freescale/p1_twr/Kconfig" source "board/freescale/qemu-ppce500/Kconfig" -source "board/freescale/t208xrdb/Kconfig" source "board/freescale/t4qds/Kconfig" source "board/freescale/t4rdb/Kconfig" source "board/gdsys/p1022/Kconfig" diff --git a/board/freescale/t208xrdb/Kconfig b/board/freescale/t208xrdb/Kconfig deleted file mode 100644 index 6f0b012bab..0000000000 --- a/board/freescale/t208xrdb/Kconfig +++ /dev/null @@ -1,14 +0,0 @@ -if TARGET_T2080RDB - -config SYS_BOARD - default "t208xrdb" - -config SYS_VENDOR - default "freescale" - -config SYS_CONFIG_NAME - default "T208xRDB" - -source "board/freescale/common/Kconfig" - -endif diff --git a/board/freescale/t208xrdb/MAINTAINERS b/board/freescale/t208xrdb/MAINTAINERS deleted file mode 100644 index f894f77b73..0000000000 --- a/board/freescale/t208xrdb/MAINTAINERS +++ /dev/null @@ -1,15 +0,0 @@ -T208XRDB BOARD -M: Shengzhou Liu Shengzhou.Liu@nxp.com -S: Maintained -F: board/freescale/t208xrdb/ -F: include/configs/T208xRDB.h -F: configs/T2080RDB_defconfig -F: configs/T2080RDB_NAND_defconfig -F: configs/T2080RDB_SDCARD_defconfig -F: configs/T2080RDB_SPIFLASH_defconfig -F: configs/T2080RDB_SRIO_PCIE_BOOT_defconfig - -T2080RDB_SECURE_BOOT BOARD -M: Ruchika Gupta ruchika.gupta@nxp.com -S: Maintained -F: configs/T2080RDB_SECURE_BOOT_defconfig diff --git a/board/freescale/t208xrdb/Makefile b/board/freescale/t208xrdb/Makefile deleted file mode 100644 index 25ea66a024..0000000000 --- a/board/freescale/t208xrdb/Makefile +++ /dev/null @@ -1,16 +0,0 @@ -# -# Copyright 2014 Freescale Semiconductor, Inc. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -ifdef CONFIG_SPL_BUILD -obj-y += spl.o -else -obj-$(CONFIG_TARGET_T2080RDB) += t208xrdb.o eth_t208xrdb.o cpld.o -obj-$(CONFIG_PCI) += pci.o -endif - -obj-y += ddr.o -obj-y += law.o -obj-y += tlb.o diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README deleted file mode 100644 index 9e4b28faf4..0000000000 --- a/board/freescale/t208xrdb/README +++ /dev/null @@ -1,283 +0,0 @@ -T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC. -It can work in two mode: standalone mode and PCIe endpoint mode. - -T2080 SoC Overview ------------------- -The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power -Architecture processor cores with high-performance datapath acceleration -logic and network and peripheral bus interfaces required for networking, -telecom/datacom, wireless infrastructure, and mil/aerospace applications. - -T2080 includes the following functions and features: - - Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz - - 2MB L2 cache and 512KB CoreNet platform cache (CPC) - - Hierarchical interconnect fabric - - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving - - Data Path Acceleration Architecture (DPAA) incorporating acceleration - - 16 SerDes lanes up to 10.3125 GHz - - 8 Ethernet interfaces, supporting combinations of the following: - - Up to four 10 Gbps Ethernet MACs - - Up to eight 1 Gbps Ethernet MACs - - Up to four 2.5 Gbps Ethernet MACs - - High-speed peripheral interfaces - - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) - - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz - - Additional peripheral interfaces - - Two serial ATA (SATA 2.0) controllers - - Two high-speed USB 2.0 controllers with integrated PHY - - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC) - - Enhanced serial peripheral interface (eSPI) - - Four I2C controllers - - Four 2-pin UARTs or two 4-pin UARTs - - Integrated Flash Controller supporting NAND and NOR flash - - Three eight-channel DMA engines - - Support for hardware virtualization and partitioning enforcement - - QorIQ Platform's Trust Architecture 2.0 - -Differences between T2080 and T2081 ------------------------------------ - Feature T2080 T2081 - 1G Ethernet numbers: 8 6 - 10G Ethernet numbers: 4 2 - SerDes lanes: 16 8 - Serial RapidIO,RMan: 2 no - SATA Controller: 2 no - Aurora: yes no - SoC Package: 896-pins 780-pins - - -T2080PCIe-RDB board Overview ----------------------------- - - SERDES Configuration - - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10) - - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2) - - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3) - - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2) - - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2) - - SerDes-2 Lane G-H: to SATA1 & SATA2 - - Ethernet - - Two on-board 10M/100M/1G RGMII ethernet ports - - Two on-board 10Gbps XFI fiber ports - - Two on-board 10Gbps Base-T copper ports - - DDR Memory - - Supports 72bit 4GB DDR3-LP SODIMM - - PCIe - - One PCIe x4 gold-finger - - One PCIe x4 connector - - One PCIe x2 end-point device (C293 Crypto co-processor) - - IFC/Local Bus - - NOR: 128MB 16-bit NOR Flash - - NAND: 1GB 8-bit NAND flash - - CPLD: for system controlling with programable header on-board - - SATA - - Two SATA 2.0 onnectors on-board - - USB - - Supports two USB 2.0 ports with integrated PHYs - - Two type A ports with 5V@1.5A per port. - - SDHC - - one TF-card connector on-board - - SPI - - On-board 64MB SPI flash - - Other - - Two Serial ports - - Four I2C ports - - -System Memory map ------------------ -Start Address End Address Description Size -0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB -0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB -0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB -0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB -0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB -0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB -0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB -0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB -0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB -0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB -0xF_0000_0000 0xF_003F_FFFF DCSR 4MB -0xC_4000_0000 0xC_4FFF_FFFF PCI Express 4 Mem Space 256MB -0xC_3000_0000 0xC_3FFF_FFFF PCI Express 3 Mem Space 256MB -0xC_2000_0000 0xC_2FFF_FFFF PCI Express 2 Mem Space 256MB -0xC_0000_0000 0xC_1FFF_FFFF PCI Express 1 Mem Space 512MB -0x0_0000_0000 0x0_ffff_ffff DDR 4GB - - -128M NOR Flash memory Map -------------------------- -Start Address End Address Definition Max size -0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB -0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB -0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB -0xEFE00000 0xEFE3FFFF PHY CS4315 firmware 256KB -0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB -0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB -0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB -0xEC000000 0xEC01FFFF RCW (alt bank) 128KB -0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB -0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB -0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB -0xEBE00000 0xEBE3FFFF PHY CS4315 firmware (alt bank) 256KB -0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB -0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB -0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB -0xE8000000 0xE801FFFF RCW (current bank) 128KB - - -T2080PCIe-RDB Ethernet Port Map -------------------------------- -Label In Uboot In Linux FMan Address Comments PHY -ETH0 FM1@GTEC1 fm1-mac9 0xfe4f0000 10G SFP+ (CS4315) -ETH1 FM1@GTEC2 fm1-mac10 0xfe4f2000 10G SFP+ (CS4315) -ETH2 FM1@GTEC3 fm1-mac1 0xfe4e0000 10G Base-T (AQ1202) -ETH3 FM1@GTEC4 fm1-mac2 0xfe4e2000 10G Base-T (AQ1202) -ETH4 FM1@DTSEC3 fm1-mac3 0xfe4e4000 1G RGMII (RTL8211E) -ETH5 FM1@DTSEC4 fm1-mac4 0xfe4e6000 1G RGMII (RTL8211E) - - -T2080PCIe-RDB Default DIP-Switch setting ----------------------------------------- -SW1[1:8] = '00010011' -SW2[1:8] = '10111111' -SW3[1:8] = '11100001' - -Software configurations and board settings ------------------------------------------- -1. NOR boot: - a. build NOR boot image - $ make T2080RDB_config - $ make - b. program u-boot.bin image to NOR flash - => tftp 1000000 u-boot.bin - => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize - set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot - - Switching between default bank and alternate bank on NOR flash - To change boot source to vbank4: - via software: run command 'cpld reset altbank' in U-Boot. - via DIP-switch: set SW3[5:7] = '100' - - To change boot source to vbank0: - via software: run command 'cpld reset' in U-Boot. - via DIP-Switch: set SW3[5:7] = '000' - -2. NAND Boot: - a. build PBL image for NAND boot - $ make T2080RDB_NAND_config - $ make - b. program u-boot-with-spl-pbl.bin to NAND flash - => tftp 1000000 u-boot-with-spl-pbl.bin - => nand erase 0 d0000 - => nand write 1000000 0 $filesize - set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot - -3. SPI Boot: - a. build PBL image for SPI boot - $ make T2080RDB_SPIFLASH_config - $ make - b. program u-boot-with-spl-pbl.bin to SPI flash - => tftp 1000000 u-boot-with-spl-pbl.bin - => sf probe 0 - => sf erase 0 d0000 - => sf write 1000000 0 $filesize - set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot - -4. SD Boot: - a. build PBL image for SD boot - $ make T2080RDB_SDCARD_config - $ make - b. program u-boot-with-spl-pbl.bin to micro-SD/TF card - => tftp 1000000 u-boot-with-spl-pbl.bin - => mmc write 1000000 8 0x800 - set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot - - -2-stage NAND/SPI/SD boot loader -------------------------------- -PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. -SPL further initializes DDR using SPD and environment variables -and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR. -Finally SPL transers control to U-Boot for futher booting. - -SPL has following features: - - Executes within 256K - - No relocation required - -Run time view of SPL framework -------------------------------------------------- -|Area | Address | -------------------------------------------------- -|SecureBoot header | 0xFFFC0000 (32KB) | -------------------------------------------------- -|GD, BD | 0xFFFC8000 (4KB) | -------------------------------------------------- -|ENV | 0xFFFC9000 (8KB) | -------------------------------------------------- -|HEAP | 0xFFFCB000 (50KB) | -------------------------------------------------- -|STACK | 0xFFFD8000 (22KB) | -------------------------------------------------- -|U-Boot SPL | 0xFFFD8000 (160KB) | -------------------------------------------------- - -NAND Flash memory Map on T2080RDB --------------------------------------------------------------- -Start End Definition Size -0x000000 0x0FFFFF U-Boot img 1MB (2 blocks) -0x100000 0x17FFFF U-Boot env 512KB (1 block) -0x180000 0x1FFFFF FMAN ucode 512KB (1 block) -0x200000 0x27FFFF CS4315 ucode 512KB (1 block) - - -Micro SD Card memory Map on T2080RDB ----------------------------------------------------- -Block #blocks Definition Size -0x008 2048 U-Boot img 1MB -0x800 0016 U-Boot env 8KB -0x820 0128 FMAN ucode 64KB -0x8a0 0512 CS4315 ucode 256KB - - -SPI Flash memory Map on T2080RDB ----------------------------------------------------- -Start End Definition Size -0x000000 0x0FFFFF U-Boot img 1MB -0x100000 0x101FFF U-Boot env 8KB -0x110000 0x11FFFF FMAN ucode 64KB -0x120000 0x15FFFF CS4315 ucode 256KB - - -How to update the ucode of Cortina CS4315/CS4340 10G PHY --------------------------------------------------------- -=> tftp 1000000 CS4315-CS4340-PHY-ucode.txt -=> pro off all;era 0xefe00000 0xefefffff;cp.b 1000000 0xefe00000 $filesize - - -How to update the ucode of Freescale FMAN ------------------------------------------ -=> tftp 1000000 fsl_fman_ucode_t2080_r1.0.bin -=> pro off all;erase 0xeff00000 0xeff1ffff;cp 1000000 0xeff00000 $filesize - - -For more details, please refer to T2080PCIe-RDB User Guide and access -website www.freescale.com and Freescale QorIQ SDK Infocenter document. - -Device tree support and how to enable it for different configs --------------------------------------------------------------- -Device tree support is available for t2080rdb for below mentioned boot, -1. NOR Boot -2. NAND Boot -3. SD Boot -4. SPIFLASH Boot - -To enable device tree support for other boot, below configs need to be -enabled in relative defconfig file, -1. CONFIG_DEFAULT_DEVICE_TREE="t2080rdb" (Change default device tree name if required) -2. CONFIG_OF_CONTROL -3. CONFIG_MPC85XX_HAVE_RESET_VECTOR if reset vector is located at - CONFIG_RESET_VECTOR_ADDRESS - 0xffc - -If device tree support is enabled in defconfig, -1. use 'u-boot-with-dtb.bin' for NOR boot. -2. use 'u-boot-with-spl-pbl.bin' for other boot. diff --git a/board/freescale/t208xrdb/cpld.c b/board/freescale/t208xrdb/cpld.c deleted file mode 100644 index b9ba62adff..0000000000 --- a/board/freescale/t208xrdb/cpld.c +++ /dev/null @@ -1,70 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Freescale Semiconductor - * - * Freescale T2080RDB board-specific CPLD controlling supports. - */ - -#include <common.h> -#include <command.h> -#include "cpld.h" - -u8 cpld_read(unsigned int reg) -{ - void *p = (void *)CONFIG_SYS_CPLD_BASE; - - return in_8(p + reg); -} - -void cpld_write(unsigned int reg, u8 value) -{ - void *p = (void *)CONFIG_SYS_CPLD_BASE; - - out_8(p + reg, value); -} - -/* Set the boot bank to the alternate bank */ -void cpld_set_altbank(void) -{ - u8 reg = CPLD_READ(flash_csr); - - reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK; - CPLD_WRITE(flash_csr, reg); - CPLD_WRITE(reset_ctl, CPLD_LBMAP_RESET); -} - -/* Set the boot bank to the default bank */ -void cpld_set_defbank(void) -{ - u8 reg = CPLD_READ(flash_csr); - - reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK; - CPLD_WRITE(flash_csr, reg); - CPLD_WRITE(reset_ctl, CPLD_LBMAP_RESET); -} - -int do_cpld(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) -{ - int rc = 0; - - if (argc <= 1) - return cmd_usage(cmdtp); - - if (strcmp(argv[1], "reset") == 0) { - if (strcmp(argv[2], "altbank") == 0) - cpld_set_altbank(); - else - cpld_set_defbank(); - } else { - rc = cmd_usage(cmdtp); - } - - return rc; -} - -U_BOOT_CMD( - cpld, CONFIG_SYS_MAXARGS, 1, do_cpld, - "Reset the board or alternate bank", - "reset: reset to default bank\n" - "cpld reset altbank: reset to alternate bank\n" -); diff --git a/board/freescale/t208xrdb/cpld.h b/board/freescale/t208xrdb/cpld.h deleted file mode 100644 index bd6c203742..0000000000 --- a/board/freescale/t208xrdb/cpld.h +++ /dev/null @@ -1,44 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2014 Freescale Semiconductor - */ - -/* - * CPLD register set of T2080RDB board-specific. - */ -struct cpld_data { - u8 chip_id1; /* 0x00 - Chip ID1 register */ - u8 chip_id2; /* 0x01 - Chip ID2 register */ - u8 hw_ver; /* 0x02 - Hardware Revision Register */ - u8 sw_ver; /* 0x03 - Software Revision register */ - u8 res0[12]; /* 0x04 - 0x0F - not used */ - u8 reset_ctl; /* 0x10 - Reset control Register */ - u8 flash_csr; /* 0x11 - Flash control and status register */ - u8 thermal_csr; /* 0x12 - Thermal control and status register */ - u8 led_csr; /* 0x13 - LED control and status register */ - u8 sfp_csr; /* 0x14 - SFP+ control and status register */ - u8 misc_csr; /* 0x15 - Misc control and status register */ - u8 boot_or; /* 0x16 - Boot config override register */ - u8 boot_cfg1; /* 0x17 - Boot configuration register 1 */ - u8 boot_cfg2; /* 0x18 - Boot configuration register 2 */ -} cpld_data_t; - -u8 cpld_read(unsigned int reg); -void cpld_write(unsigned int reg, u8 value); - -#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg)) -#define CPLD_WRITE(reg, value) \ - cpld_write(offsetof(struct cpld_data, reg), value) - -/* CPLD on IFC */ -#define CPLD_LBMAP_MASK 0x3F -#define CPLD_BANK_SEL_MASK 0x07 -#define CPLD_BANK_OVERRIDE 0x40 -#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */ -#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK 0 */ -#define CPLD_LBMAP_RESET 0xFF -#define CPLD_LBMAP_SHIFT 0x03 -#define CPLD_BOOT_SEL 0x80 - -/* RSTCON Register */ -#define CPLD_RSTCON_EDC_RST 0x04 diff --git a/board/freescale/t208xrdb/ddr.c b/board/freescale/t208xrdb/ddr.c deleted file mode 100644 index 6a09d1cd22..0000000000 --- a/board/freescale/t208xrdb/ddr.c +++ /dev/null @@ -1,118 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright 2014 Freescale Semiconductor, Inc. - */ - -#include <common.h> -#include <i2c.h> -#include <hwconfig.h> -#include <init.h> -#include <log.h> -#include <asm/mmu.h> -#include <fsl_ddr_sdram.h> -#include <fsl_ddr_dimm_params.h> -#include <asm/fsl_law.h> -#include "ddr.h" - -DECLARE_GLOBAL_DATA_PTR; - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; - ulong ddr_freq; - - if (ctrl_num > 1) { - printf("Not supported controller number %d\n", ctrl_num); - return; - } - if (!pdimm->n_ranks) - return; - - pbsp = udimms[0]; - - /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr - * freqency and n_banks specified in board_specific_parameters table. - */ - ddr_freq = get_ddr_freq(0) / 1000000; - while (pbsp->datarate_mhz_high) { - if (pbsp->n_ranks == pdimm->n_ranks && - (pdimm->rank_density >> 30) >= pbsp->rank_gb) { - if (ddr_freq <= pbsp->datarate_mhz_high) { - popts->clk_adjust = pbsp->clk_adjust; - popts->wrlvl_start = pbsp->wrlvl_start; - popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; - popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - goto found; - } - pbsp_highest = pbsp; - } - pbsp++; - } - - if (pbsp_highest) { - printf("Error: board specific timing not found"); - printf("for data rate %lu MT/s\n", ddr_freq); - printf("Trying to use the highest speed (%u) parameters\n", - pbsp_highest->datarate_mhz_high); - popts->clk_adjust = pbsp_highest->clk_adjust; - popts->wrlvl_start = pbsp_highest->wrlvl_start; - popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; - popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - } else { - panic("DIMM is not supported by this board"); - } -found: - debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" - "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, " - "wrlvl_ctrl_3 0x%x\n", - pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, - pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, - pbsp->wrlvl_ctl_3); - - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; - /* - * Write leveling override - */ - popts->wrlvl_override = 1; - popts->wrlvl_sample = 0xf; - - /* - * Rtt and Rtt_WR override - */ - popts->rtt_override = 0; - - /* Enable ZQ calibration */ - popts->zq_en = 1; - - /* DHC_EN =1, ODT = 75 Ohm */ - popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); - popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); - - /* optimize cpo for erratum A-009942 */ - popts->cpo_sample = 0x54; -} - -int dram_init(void) -{ - phys_size_t dram_size; - -#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) - puts("Initializing....using SPD\n"); - dram_size = fsl_ddr_sdram(); -#else - /* DDR has been initialised by first stage boot loader */ - dram_size = fsl_ddr_sdram_size(); -#endif - dram_size = setup_ddr_tlbs(dram_size / 0x100000); - dram_size *= 0x100000; - - gd->ram_size = dram_size; - - return 0; -} diff --git a/board/freescale/t208xrdb/ddr.h b/board/freescale/t208xrdb/ddr.h deleted file mode 100644 index c00f178166..0000000000 --- a/board/freescale/t208xrdb/ddr.h +++ /dev/null @@ -1,46 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - */ - -#ifndef __DDR_H__ -#define __DDR_H__ -struct board_specific_parameters { - u32 n_ranks; - u32 datarate_mhz_high; - u32 rank_gb; - u32 clk_adjust; - u32 wrlvl_start; - u32 wrlvl_ctl_2; - u32 wrlvl_ctl_3; -}; - -/* - * These tables contain all valid speeds we want to override with board - * specific parameters. datarate_mhz_high values need to be in ascending order - * for each n_ranks group. - */ - -static const struct board_specific_parameters udimm0[] = { - /* - * memory controller 0 - * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | - * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | - */ - {2, 1200, 2, 10, 7, 0x0808090a, 0x0b0c0c0a}, - {2, 1500, 2, 10, 6, 0x07070809, 0x0a0b0b09}, - {2, 1600, 2, 10, 8, 0x0808070b, 0x0c0d0e0a}, - {2, 1700, 2, 8, 7, 0x080a0a0c, 0x0c0d0e0a}, - {2, 1900, 0, 10, 7, 0x0808080c, 0x0b0c0c09}, - {1, 1200, 2, 10, 7, 0x0808090a, 0x0b0c0c0a}, - {1, 1500, 2, 10, 6, 0x07070809, 0x0a0b0b09}, - {1, 1600, 2, 10, 8, 0x0808070b, 0x0c0d0e0a}, - {1, 1700, 2, 8, 7, 0x080a0a0c, 0x0c0d0e0a}, - {1, 1900, 0, 10, 7, 0x0808080c, 0x0b0c0c09}, - {} -}; - -static const struct board_specific_parameters *udimms[] = { - udimm0, -}; -#endif diff --git a/board/freescale/t208xrdb/eth_t208xrdb.c b/board/freescale/t208xrdb/eth_t208xrdb.c deleted file mode 100644 index db4718128d..0000000000 --- a/board/freescale/t208xrdb/eth_t208xrdb.c +++ /dev/null @@ -1,107 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - * - * Shengzhou Liu Shengzhou.Liu@freescale.com - */ - -#include <common.h> -#include <command.h> -#include <fdt_support.h> -#include <net.h> -#include <netdev.h> -#include <asm/mmu.h> -#include <asm/processor.h> -#include <asm/immap_85xx.h> -#include <asm/fsl_law.h> -#include <asm/fsl_serdes.h> -#include <asm/fsl_portals.h> -#include <asm/fsl_liodn.h> -#include <malloc.h> -#include <fm_eth.h> -#include <fsl_mdio.h> -#include <miiphy.h> -#include <phy.h> -#include <fsl_dtsec.h> -#include <asm/fsl_serdes.h> - -int board_eth_init(bd_t *bis) -{ -#if defined(CONFIG_FMAN_ENET) - int i, interface; - struct memac_mdio_info dtsec_mdio_info; - struct memac_mdio_info tgec_mdio_info; - struct mii_dev *dev; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 srds_s1; - - srds_s1 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - - dtsec_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; - - dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; - - /* Register the 1G MDIO bus */ - fm_memac_mdio_init(bis, &dtsec_mdio_info); - - tgec_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; - tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; - - /* Register the 10G MDIO bus */ - fm_memac_mdio_init(bis, &tgec_mdio_info); - - /* Set the two on-board RGMII PHY address */ - fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR); - - switch (srds_s1) { - case 0x66: - case 0x6b: - fm_info_set_phy_address(FM1_10GEC1, CORTINA_PHY_ADDR1); - fm_info_set_phy_address(FM1_10GEC2, CORTINA_PHY_ADDR2); - fm_info_set_phy_address(FM1_10GEC3, FM1_10GEC3_PHY_ADDR); - fm_info_set_phy_address(FM1_10GEC4, FM1_10GEC4_PHY_ADDR); - break; - default: - printf("SerDes1 protocol 0x%x is not supported on T208xRDB\n", - srds_s1); - break; - } - - for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { - interface = fm_info_get_enet_if(i); - switch (interface) { - case PHY_INTERFACE_MODE_RGMII: - dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME); - fm_info_set_mdio(i, dev); - break; - default: - break; - } - } - - for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_XGMII: - dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME); - fm_info_set_mdio(i, dev); - break; - default: - break; - } - } - - cpu_eth_init(bis); -#endif /* CONFIG_FMAN_ENET */ - - return pci_eth_init(bis); -} - -void fdt_fixup_board_enet(void *fdt) -{ - return; -} diff --git a/board/freescale/t208xrdb/law.c b/board/freescale/t208xrdb/law.c deleted file mode 100644 index d3b263f59d..0000000000 --- a/board/freescale/t208xrdb/law.c +++ /dev/null @@ -1,33 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008-2014 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include <common.h> -#include <asm/fsl_law.h> -#include <asm/mmu.h> - -struct law_entry law_table[] = { - SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), -#ifdef CONFIG_SYS_BMAN_MEM_PHYS - SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), -#endif -#ifdef CONFIG_SYS_QMAN_MEM_PHYS - SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), -#endif -#ifdef CONFIG_SYS_CPLD_BASE_PHYS - SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), -#endif -#ifdef CONFIG_SYS_DCSRBAR_PHYS - /* Limit DCSR to 32M to access NPC Trace Buffer */ - SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), -#endif -#ifdef CONFIG_SYS_NAND_BASE_PHYS - SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC), -#endif -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t208xrdb/pci.c b/board/freescale/t208xrdb/pci.c deleted file mode 100644 index bd0e29744c..0000000000 --- a/board/freescale/t208xrdb/pci.c +++ /dev/null @@ -1,25 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2007-2014 Freescale Semiconductor, Inc. - */ - -#include <common.h> -#include <command.h> -#include <init.h> -#include <pci.h> -#include <asm/fsl_pci.h> -#include <linux/libfdt.h> -#include <fdt_support.h> -#include <asm/fsl_serdes.h> - -#if !defined(CONFIG_DM_PCI) -void pci_init_board(void) -{ - fsl_pcie_init_board(0); -} - -void pci_of_setup(void *blob, bd_t *bd) -{ - FT_FSL_PCI_SETUP; -} -#endif diff --git a/board/freescale/t208xrdb/spl.c b/board/freescale/t208xrdb/spl.c deleted file mode 100644 index 27e87da409..0000000000 --- a/board/freescale/t208xrdb/spl.c +++ /dev/null @@ -1,112 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* Copyright 2013 Freescale Semiconductor, Inc. - */ - -#include <common.h> -#include <clock_legacy.h> -#include <console.h> -#include <env_internal.h> -#include <init.h> -#include <malloc.h> -#include <ns16550.h> -#include <nand.h> -#include <i2c.h> -#include <mmc.h> -#include <fsl_esdhc.h> -#include <spi_flash.h> -#include "../common/spl.h" - -DECLARE_GLOBAL_DATA_PTR; - -phys_size_t get_effective_memsize(void) -{ - return CONFIG_SYS_L3_SIZE; -} - -unsigned long get_board_sys_clk(void) -{ - return CONFIG_SYS_CLK_FREQ; -} - -unsigned long get_board_ddr_clk(void) -{ - return CONFIG_DDR_CLK_FREQ; -} - -void board_init_f(ulong bootflag) -{ - u32 plat_ratio, sys_clk, ccb_clk; - ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; - - /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ - memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t)); - - /* Update GD pointer */ - gd = (gd_t *)(CONFIG_SPL_GD_ADDR); - - console_init_f(); - - /* initialize selected port with appropriate baud rate */ - sys_clk = get_board_sys_clk(); - plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f; - ccb_clk = sys_clk * plat_ratio / 2; - - NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, - ccb_clk / 16 / CONFIG_BAUDRATE); - -#if defined(CONFIG_SPL_MMC_BOOT) - puts("\nSD boot...\n"); -#elif defined(CONFIG_SPL_SPI_BOOT) - puts("\nSPI boot...\n"); -#elif defined(CONFIG_SPL_NAND_BOOT) - puts("\nNAND boot...\n"); -#endif - - relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0); -} - -void board_init_r(gd_t *gd, ulong dest_addr) -{ - bd_t *bd; - - bd = (bd_t *)(gd + sizeof(gd_t)); - memset(bd, 0, sizeof(bd_t)); - gd->bd = bd; - bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR; - bd->bi_memsize = CONFIG_SYS_L3_SIZE; - - arch_cpu_init(); - get_clocks(); - mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, - CONFIG_SPL_RELOC_MALLOC_SIZE); - gd->flags |= GD_FLG_FULL_MALLOC_INIT; - -#ifdef CONFIG_SPL_NAND_BOOT - nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); -#endif -#ifdef CONFIG_SPL_MMC_BOOT - mmc_initialize(bd); - mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); -#endif -#ifdef CONFIG_SPL_SPI_BOOT - fsl_spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); -#endif - - gd->env_addr = (ulong)(SPL_ENV_ADDR); - gd->env_valid = ENV_VALID; - - i2c_init_all(); - - dram_init(); - -#ifdef CONFIG_SPL_MMC_BOOT - mmc_boot(); -#elif defined(CONFIG_SPL_SPI_BOOT) - fsl_spi_boot(); -#elif defined(CONFIG_SPL_NAND_BOOT) - nand_boot(); -#endif -} diff --git a/board/freescale/t208xrdb/t2080_nand_rcw.cfg b/board/freescale/t208xrdb/t2080_nand_rcw.cfg deleted file mode 100644 index 8096ff9f37..0000000000 --- a/board/freescale/t208xrdb/t2080_nand_rcw.cfg +++ /dev/null @@ -1,19 +0,0 @@ -#PBL preamble and RCW header -aa55aa55 010e0100 - -#For T2080 v1.0 -#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s -#120c0017 15000000 00000000 00000000 -#66150002 00008400 ec104000 c1000000 -#00000000 00000000 00000000 000307fc -#00000000 00000000 00000000 00000004 - -#For T2080 v1.1 -#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s -#1206001b 15000000 00000000 00000000 - -#SerDes=0x66_0x15, Core:1800MHz, DDR:1867MT/s -1207001b 15000000 00000000 00000000 -66150002 00000000 e8104000 c1000000 -00800000 00000000 00000000 000307fc -00000000 00000000 00000000 00000004 diff --git a/board/freescale/t208xrdb/t2080_pbi.cfg b/board/freescale/t208xrdb/t2080_pbi.cfg deleted file mode 100644 index 43be8a864e..0000000000 --- a/board/freescale/t208xrdb/t2080_pbi.cfg +++ /dev/null @@ -1,40 +0,0 @@ -# -# Copyright 2013 Freescale Semiconductor, Inc. -# -# SPDX-License-Identifier: GPL-2.0+ -# -# Refer doc/README.pblimage for more details about how-to configure -# and create PBL boot image -# - -#PBI commands -#Initialize CPC1 -09010000 00200400 -09138000 00000000 -091380c0 00000100 -#512KB SRAM -09010100 00000000 -09010104 fff80009 -09010f00 08000000 -#enable CPC1 -09010000 80000000 -#Configure LAW for CPC1 -09000d00 00000000 -09000d04 fff80000 -09000d08 81000012 -#Initialize eSPI controller, default configuration is slow for eSPI to -#load data, this configuration comes from u-boot eSPI driver. -09110000 80000403 -09110020 2d170008 -09110024 00100008 -09110028 00100008 -0911002c 00100008 -#Errata for slowing down the MDC clock to make it <= 2.5 MHZ -094fc030 00008148 -094fd030 00008148 -#Configure alternate space -09000010 00000000 -09000014 ff000000 -09000018 81000000 -#Flush PBL data -091380c0 00100000 diff --git a/board/freescale/t208xrdb/t2080_sd_rcw.cfg b/board/freescale/t208xrdb/t2080_sd_rcw.cfg deleted file mode 100644 index 6309b1d220..0000000000 --- a/board/freescale/t208xrdb/t2080_sd_rcw.cfg +++ /dev/null @@ -1,19 +0,0 @@ -#PBL preamble and RCW header -aa55aa55 010e0100 - -#For T2080 v1.0 -#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s -#120c0017 15000000 00000000 00000000 -#66150002 00008400 ec104000 c1000000 -#00000000 00000000 00000000 000307fc -#00000000 00000000 00000000 00000004 - -#For T2080 v1.1 -#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s -#1206001b 15000000 00000000 00000000 - -#SerDes=0x66_0x15, Core:1800MHz, DDR:1867MT/s -1207001b 15000000 00000000 00000000 -66150002 00000000 68104000 c1000000 -00800000 00000000 00000000 000307fc -00000000 00000000 00000000 00000004 diff --git a/board/freescale/t208xrdb/t2080_spi_rcw.cfg b/board/freescale/t208xrdb/t2080_spi_rcw.cfg deleted file mode 100644 index f167495887..0000000000 --- a/board/freescale/t208xrdb/t2080_spi_rcw.cfg +++ /dev/null @@ -1,19 +0,0 @@ -#PBL preamble and RCW header -aa55aa55 010e0100 - -#For T2080 v1.0 -#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s -#120c0017 15000000 00000000 00000000 -#66150002 00008400 ec104000 c1000000 -#00000000 00000000 00000000 000307fc -#00000000 00000000 00000000 00000004 - -#For T2080 v1.1 -#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s -#1206001b 15000000 00000000 00000000 - -#SerDes=0x66_0x15, Core:1800MHz, DDR:1867MT/s -1207001b 15000000 00000000 00000000 -66150002 00000000 58104000 c1000000 -00800000 00000000 00000000 000307fc -00000000 00000000 00000000 00000004 diff --git a/board/freescale/t208xrdb/t208xrdb.c b/board/freescale/t208xrdb/t208xrdb.c deleted file mode 100644 index 24f0d0764c..0000000000 --- a/board/freescale/t208xrdb/t208xrdb.c +++ /dev/null @@ -1,142 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2009-2013 Freescale Semiconductor, Inc. - */ - -#include <common.h> -#include <command.h> -#include <env.h> -#include <fdt_support.h> -#include <i2c.h> -#include <image.h> -#include <init.h> -#include <netdev.h> -#include <linux/compiler.h> -#include <asm/mmu.h> -#include <asm/processor.h> -#include <asm/immap_85xx.h> -#include <asm/fsl_law.h> -#include <asm/fsl_serdes.h> -#include <asm/fsl_liodn.h> -#include <fm_eth.h> -#include "t208xrdb.h" -#include "cpld.h" -#include "../common/vid.h" - -DECLARE_GLOBAL_DATA_PTR; - -int checkboard(void) -{ - struct cpu_type *cpu = gd->arch.cpu; - static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"}; - - printf("Board: %sRDB, ", cpu->name); - printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ", - CPLD_READ(hw_ver), CPLD_READ(sw_ver)); - -#ifdef CONFIG_SDCARD - puts("SD/MMC\n"); -#elif CONFIG_SPIFLASH - puts("SPI\n"); -#else - u8 reg; - - reg = CPLD_READ(flash_csr); - - if (reg & CPLD_BOOT_SEL) { - puts("NAND\n"); - } else { - reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT); - printf("NOR vBank%d\n", reg); - } -#endif - - puts("SERDES Reference Clocks:\n"); - printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]); - printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[0], freq[0]); - - return 0; -} - -int board_early_init_r(void) -{ - const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; - int flash_esel = find_tlb_idx((void *)flashbase, 1); - /* - * Remap Boot flash + PROMJET region to caching-inhibited - * so that flash can be erased properly. - */ - - /* Flush d-cache and invalidate i-cache of any FLASH data */ - flush_dcache(); - invalidate_icache(); - if (flash_esel == -1) { - /* very unlikely unless something is messed up */ - puts("Error: Could not find TLB for FLASH BASE\n"); - flash_esel = 2; /* give our best effort to continue */ - } else { - /* invalidate existing TLB entry for flash + promjet */ - disable_tlb(flash_esel); - } - - set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, flash_esel, BOOKE_PAGESZ_256M, 1); - - /* - * Adjust core voltage according to voltage ID - * This function changes I2C mux to channel 2. - */ - if (adjust_vdd(0)) - printf("Warning: Adjusting core voltage failed.\n"); - return 0; -} - -unsigned long get_board_sys_clk(void) -{ - return CONFIG_SYS_CLK_FREQ; -} - -unsigned long get_board_ddr_clk(void) -{ - return CONFIG_DDR_CLK_FREQ; -} - -int misc_init_r(void) -{ - u8 reg; - - /* Reset CS4315 PHY */ - reg = CPLD_READ(reset_ctl); - reg |= CPLD_RSTCON_EDC_RST; - CPLD_WRITE(reset_ctl, reg); - - return 0; -} - -int ft_board_setup(void *blob, bd_t *bd) -{ - phys_addr_t base; - phys_size_t size; - - ft_cpu_setup(blob, bd); - - base = env_get_bootm_low(); - size = env_get_bootm_size(); - - fdt_fixup_memory(blob, (u64)base, (u64)size); - -#ifdef CONFIG_PCI - pci_of_setup(blob, bd); -#endif - - fdt_fixup_liodn(blob); - fsl_fdt_fixup_dr_usb(blob, bd); - -#ifdef CONFIG_SYS_DPAA_FMAN - fdt_fixup_fman_ethernet(blob); - fdt_fixup_board_enet(blob); -#endif - - return 0; -} diff --git a/board/freescale/t208xrdb/t208xrdb.h b/board/freescale/t208xrdb/t208xrdb.h deleted file mode 100644 index 2f630ef1ca..0000000000 --- a/board/freescale/t208xrdb/t208xrdb.h +++ /dev/null @@ -1,12 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - */ - -#ifndef __CORENET_DS_H__ -#define __CORENET_DS_H__ - -void fdt_fixup_board_enet(void *blob); -void pci_of_setup(void *blob, bd_t *bd); - -#endif diff --git a/board/freescale/t208xrdb/tlb.c b/board/freescale/t208xrdb/tlb.c deleted file mode 100644 index 542ab1e034..0000000000 --- a/board/freescale/t208xrdb/tlb.c +++ /dev/null @@ -1,152 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008-2014 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include <common.h> -#include <asm/mmu.h> - -struct fsl_e_tlb_entry tlb_table[] = { - /* TLB 0 - for temp stack in cache */ - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, - CONFIG_SYS_INIT_RAM_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - - /* TLB 1 */ - /* *I*** - Covers boot page */ -#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) - /* - * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the - * SRAM is at 0xfff00000, it covered the 0xfffff000. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_1M, 1), -#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) - /* - * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the - * space is at 0xfff00000, it covered the 0xfffff000. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR, - CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, - 0, 0, BOOKE_PAGESZ_1M, 1), -#else - SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_4K, 1), -#endif - - /* *I*G* - CCSRBAR */ - SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_16M, 1), - - /* *I*G* - Flash, localbus */ - /* This will be changed to *I*G* after relocation to RAM. */ - SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, - 0, 2, BOOKE_PAGESZ_256M, 1), - -#ifndef CONFIG_SPL_BUILD - /* *I*G* - PCIe 1, 0x80000000 */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_512M, 1), - - /* *I*G* - PCIe 2, 0xa0000000 */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 4, BOOKE_PAGESZ_256M, 1), - - /* *I*G* - PCIe 3, 0xb0000000 */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 5, BOOKE_PAGESZ_256M, 1), - - - /* *I*G* - PCIe 4, 0xc0000000 */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE4_MEM_VIRT, CONFIG_SYS_PCIE4_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 6, BOOKE_PAGESZ_256M, 1), - - /* *I*G* - PCI I/O */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 7, BOOKE_PAGESZ_256K, 1), - - /* Bman/Qman */ -#ifdef CONFIG_SYS_BMAN_MEM_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 9, BOOKE_PAGESZ_16M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, - CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 10, BOOKE_PAGESZ_16M, 1), -#endif -#ifdef CONFIG_SYS_QMAN_MEM_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 11, BOOKE_PAGESZ_16M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, - CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 12, BOOKE_PAGESZ_16M, 1), -#endif -#endif -#ifdef CONFIG_SYS_DCSRBAR_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 13, BOOKE_PAGESZ_32M, 1), -#endif -#ifdef CONFIG_SYS_NAND_BASE - /* - * *I*G - NAND - * entry 14 and 15 has been used hard coded, they will be disabled - * in cpu_init_f, so we use entry 16 for nand. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 16, BOOKE_PAGESZ_64K, 1), -#endif -#ifdef CONFIG_SYS_CPLD_BASE - SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 17, BOOKE_PAGESZ_4K, 1), -#endif -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE - /* - * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for - * fetching ucode and ENV from master - */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR, - CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, - 0, 18, BOOKE_PAGESZ_1M, 1), -#endif -#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD) - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, - 0, 19, BOOKE_PAGESZ_2G, 1) -#endif - -}; - -int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/configs/T2080RDB_NAND_defconfig b/configs/T2080RDB_NAND_defconfig deleted file mode 100644 index 81baa5dbdd..0000000000 --- a/configs/T2080RDB_NAND_defconfig +++ /dev/null @@ -1,84 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T2080RDB=y -CONFIG_SYS_CUSTOM_LDSCRIPT=y -CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_NAND_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_MEMTEST=y -CONFIG_SYS_ALT_MEMTEST=y -CONFIG_SYS_MEMTEST_START=0x00200000 -CONFIG_SYS_MEMTEST_END=0x00400000 -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_MTDPARTS=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)" -# CONFIG_CMD_IRQ is not set -CONFIG_OF_CONTROL=y -CONFIG_DEFAULT_DEVICE_TREE="t2080rdb" -CONFIG_ENV_IS_IN_NAND=y -CONFIG_DM=y -CONFIG_FSL_CAAM=y -CONFIG_DM_I2C=y -CONFIG_DM_MMC=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_MTD_RAW_NAND=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_CORTINA=y -CONFIG_SYS_CORTINA_FW_IN_NAND=y -CONFIG_PHY_REALTEK=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_DM_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_FSL=y -CONFIG_SYS_QE_FMAN_FW_IN_NAND=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_DM_USB=y diff --git a/configs/T2080RDB_SDCARD_defconfig b/configs/T2080RDB_SDCARD_defconfig deleted file mode 100644 index a1d7d87b60..0000000000 --- a/configs/T2080RDB_SDCARD_defconfig +++ /dev/null @@ -1,81 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_SPL_MMC_SUPPORT=y -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T2080RDB=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_MMC_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_MEMTEST=y -CONFIG_SYS_ALT_MEMTEST=y -CONFIG_SYS_MEMTEST_START=0x00200000 -CONFIG_SYS_MEMTEST_END=0x00400000 -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_MTDPARTS=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)" -# CONFIG_CMD_IRQ is not set -CONFIG_OF_CONTROL=y -CONFIG_DEFAULT_DEVICE_TREE="t2080rdb" -CONFIG_ENV_IS_IN_MMC=y -CONFIG_DM=y -CONFIG_FSL_CAAM=y -CONFIG_DM_I2C=y -CONFIG_DM_MMC=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_CORTINA=y -CONFIG_SYS_CORTINA_FW_IN_MMC=y -CONFIG_PHY_REALTEK=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_DM_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_FSL=y -CONFIG_SYS_QE_FMAN_FW_IN_MMC=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_DM_USB=y diff --git a/configs/T2080RDB_SECURE_BOOT_defconfig b/configs/T2080RDB_SECURE_BOOT_defconfig deleted file mode 100644 index 7d04a94116..0000000000 --- a/configs/T2080RDB_SECURE_BOOT_defconfig +++ /dev/null @@ -1,63 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_NXP_ESBC=y -CONFIG_MPC85xx=y -CONFIG_TARGET_T2080RDB=y -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_MEMTEST=y -CONFIG_SYS_ALT_MEMTEST=y -CONFIG_SYS_MEMTEST_START=0x00200000 -CONFIG_SYS_MEMTEST_END=0x00400000 -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_MTDPARTS=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)" -# CONFIG_CMD_IRQ is not set -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_DM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_CORTINA=y -CONFIG_PHY_REALTEK=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_RSA=y -CONFIG_SPL_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T2080RDB_SPIFLASH_defconfig b/configs/T2080RDB_SPIFLASH_defconfig deleted file mode 100644 index c433a922e6..0000000000 --- a/configs/T2080RDB_SPIFLASH_defconfig +++ /dev/null @@ -1,84 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T2080RDB=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_SPI_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_MEMTEST=y -CONFIG_SYS_ALT_MEMTEST=y -CONFIG_SYS_MEMTEST_START=0x00200000 -CONFIG_SYS_MEMTEST_END=0x00400000 -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_MTDPARTS=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)" -# CONFIG_CMD_IRQ is not set -CONFIG_OF_CONTROL=y -CONFIG_DEFAULT_DEVICE_TREE="t2080rdb" -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_ENV_ADDR=0xFFFC9000 -CONFIG_DM=y -CONFIG_FSL_CAAM=y -CONFIG_DM_I2C=y -CONFIG_DM_MMC=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_CORTINA=y -CONFIG_SYS_CORTINA_FW_IN_SPIFLASH=y -CONFIG_PHY_REALTEK=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_DM_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_FSL=y -CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_DM_USB=y diff --git a/configs/T2080RDB_SRIO_PCIE_BOOT_defconfig b/configs/T2080RDB_SRIO_PCIE_BOOT_defconfig deleted file mode 100644 index a8f0a965c1..0000000000 --- a/configs/T2080RDB_SRIO_PCIE_BOOT_defconfig +++ /dev/null @@ -1,53 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xFFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T2080RDB=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="SRIO_PCIE_BOOT_SLAVE" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_MEMTEST=y -CONFIG_SYS_ALT_MEMTEST=y -CONFIG_SYS_MEMTEST_START=0x00200000 -CONFIG_SYS_MEMTEST_END=0x00400000 -# CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -# CONFIG_CMD_IRQ is not set -CONFIG_ENV_IS_IN_REMOTE=y -CONFIG_ENV_ADDR=0xFFE20000 -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_CORTINA=y -CONFIG_SYS_CORTINA_FW_IN_REMOTE=y -CONFIG_PHY_REALTEK=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_REMOTE=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T2080RDB_defconfig b/configs/T2080RDB_defconfig deleted file mode 100644 index 85e3b64ad3..0000000000 --- a/configs/T2080RDB_defconfig +++ /dev/null @@ -1,68 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T2080RDB=y -CONFIG_MPC85XX_HAVE_RESET_VECTOR=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_MEMTEST=y -CONFIG_SYS_ALT_MEMTEST=y -CONFIG_SYS_MEMTEST_START=0x00200000 -CONFIG_SYS_MEMTEST_END=0x00400000 -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_MTDPARTS=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)" -# CONFIG_CMD_IRQ is not set -CONFIG_OF_CONTROL=y -CONFIG_DEFAULT_DEVICE_TREE="t2080rdb" -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xEFF20000 -CONFIG_DM=y -CONFIG_FSL_CAAM=y -CONFIG_DM_I2C=y -CONFIG_DM_MMC=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_CORTINA=y -CONFIG_PHY_REALTEK=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_DM_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_FSL=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_DM_USB=y diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h deleted file mode 100644 index 70eafc3e28..0000000000 --- a/include/configs/T208xRDB.h +++ /dev/null @@ -1,717 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - * Copyright 2020 NXP - */ - -/* - * T2080 RDB/PCIe board configuration file - */ - -#ifndef __T2080RDB_H -#define __T2080RDB_H - -#include <linux/stringify.h> - -#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ -#define CONFIG_FSL_SATA_V2 - -/* High Level Configuration Options */ -#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ -#define CONFIG_ENABLE_36BIT_PHYS - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_ADDR_MAP 1 -#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ -#endif - -#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ -#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS -#define CONFIG_ENV_OVERWRITE - -#ifdef CONFIG_RAMBOOT_PBL -#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg - -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_PAD_TO 0x40000 -#define CONFIG_SPL_MAX_SIZE 0x28000 -#define RESET_VECTOR_OFFSET 0x27FFC -#define BOOT_PAGE_OFFSET 0x27000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SPL_SKIP_RELOCATE -#define CONFIG_SPL_COMMON_INIT_DDR -#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE -#endif - -#ifdef CONFIG_MTD_RAW_NAND -#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) -#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg -#endif - -#ifdef CONFIG_SPIFLASH -#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC -#define CONFIG_SPL_SPI_FLASH_MINIMAL -#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) -#ifndef CONFIG_SPL_BUILD -#define CONFIG_SYS_MPC85XX_NO_RESETVEC -#endif -#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg -#endif - -#ifdef CONFIG_SDCARD -#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC -#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) -#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) -#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) -#ifndef CONFIG_SPL_BUILD -#define CONFIG_SYS_MPC85XX_NO_RESETVEC -#endif -#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg -#endif - -#endif /* CONFIG_RAMBOOT_PBL */ - -#define CONFIG_SRIO_PCIE_BOOT_MASTER -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE -/* Set 1M boot space */ -#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) -#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) -#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#endif - -#ifndef CONFIG_RESET_VECTOR_ADDRESS -#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc -#endif - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_SYS_CACHE_STASHING -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_DDR_ECC -#ifdef CONFIG_DDR_ECC -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_MEM_INIT_VALUE 0xdeadbeef -#endif - -#if defined(CONFIG_SPIFLASH) -#elif defined(CONFIG_SDCARD) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#endif - -#ifndef __ASSEMBLY__ -unsigned long get_board_sys_clk(void); -unsigned long get_board_ddr_clk(void); -#endif - -#define CONFIG_SYS_CLK_FREQ 66660000 -#define CONFIG_DDR_CLK_FREQ 133330000 - -/* - * Config the L3 Cache as L3 SRAM - */ -#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 -#define CONFIG_SYS_L3_SIZE (512 << 10) -#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) -#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) -#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) - -#define CONFIG_SYS_DCSRBAR 0xf0000000 -#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull - -/* EEPROM */ -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#define CONFIG_SYS_EEPROM_BUS_NUM 0 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 - -/* - * DDR Setup - */ -#define CONFIG_VERY_BIG_RAM -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) -#define CONFIG_DDR_SPD -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ -#define SPD_EEPROM_ADDRESS1 0x51 -#define SPD_EEPROM_ADDRESS2 0x52 -#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 -#define CTRL_INTLV_PREFERED cacheline - -/* - * IFC Definitions - */ -#define CONFIG_SYS_FLASH_BASE 0xe8000000 -#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) -#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) - -/* NOR Flash Timing Params */ -#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 - -#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ - FTIM0_NOR_TEADC(0x5) | \ - FTIM0_NOR_TEAHC(0x5)) -#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ - FTIM1_NOR_TRAD_NOR(0x1A) |\ - FTIM1_NOR_TSEQRAD_NOR(0x13)) -#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ - FTIM2_NOR_TCH(0x4) | \ - FTIM2_NOR_TWPH(0x0E) | \ - FTIM2_NOR_TWP(0x1c)) -#define CONFIG_SYS_NOR_FTIM3 0x0 - -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } - -/* CPLD on IFC */ -#define CONFIG_SYS_CPLD_BASE 0xffdf0000 -#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) -#define CONFIG_SYS_CSPR2_EXT (0xf) -#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ - | CSPR_PORT_SIZE_8 \ - | CSPR_MSEL_GPCM \ - | CSPR_V) -#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) -#define CONFIG_SYS_CSOR2 0x0 - -/* CPLD Timing parameters for IFC CS2 */ -#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ - FTIM0_GPCM_TEADC(0x0e) | \ - FTIM0_GPCM_TEAHC(0x0e)) -#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ - FTIM1_GPCM_TRAD(0x1f)) -#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ - FTIM2_GPCM_TCH(0x8) | \ - FTIM2_GPCM_TWP(0x1f)) -#define CONFIG_SYS_CS2_FTIM3 0x0 - -/* NAND Flash on IFC */ -#define CONFIG_NAND_FSL_IFC -#define CONFIG_SYS_NAND_BASE 0xff800000 -#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) - -#define CONFIG_SYS_NAND_CSPR_EXT (0xf) -#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ - | CSPR_MSEL_NAND /* MSEL = NAND */ \ - | CSPR_V) -#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) - -#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ - | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ - | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ - | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ - | CSOR_NAND_PGS_2K /* Page Size = 2K */\ - | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ - | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ - -#define CONFIG_SYS_NAND_ONFI_DETECTION - -/* ONFI NAND Flash mode0 Timing Params */ -#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ - FTIM0_NAND_TWP(0x18) | \ - FTIM0_NAND_TWCHT(0x07) | \ - FTIM0_NAND_TWH(0x0a)) -#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ - FTIM1_NAND_TWBE(0x39) | \ - FTIM1_NAND_TRR(0x0e) | \ - FTIM1_NAND_TRP(0x18)) -#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ - FTIM2_NAND_TREH(0x0a) | \ - FTIM2_NAND_TWHRE(0x1e)) -#define CONFIG_SYS_NAND_FTIM3 0x0 - -#define CONFIG_SYS_NAND_DDR_LAW 11 -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) - -#if defined(CONFIG_MTD_RAW_NAND) -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 -#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 -#else -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 -#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT -#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 -#endif - -#if defined(CONFIG_RAMBOOT_PBL) -#define CONFIG_SYS_RAMBOOT -#endif - -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE -#else -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#endif - -#define CONFIG_HWCONFIG - -/* define to use L1 as initial stack */ -#define CONFIG_L1_INIT_RAM -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 -/* The assembler doesn't like typecast */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ - ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ - CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) -#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) -#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) -#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) - -/* - * I2C - */ -#ifndef CONFIG_DM_I2C -#define CONFIG_SYS_I2C -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 -#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 -#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 -#define CONFIG_SYS_FSL_I2C_SPEED 100000 -#define CONFIG_SYS_FSL_I2C2_SPEED 100000 -#define CONFIG_SYS_FSL_I2C3_SPEED 100000 -#define CONFIG_SYS_FSL_I2C4_SPEED 100000 -#else -#define CONFIG_I2C_SET_DEFAULT_BUS_NUM -#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 -#endif - -#define CONFIG_SYS_I2C_FSL - -#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ -#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ -#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ -#define I2C_MUX_CH_DEFAULT 0x8 - -#define I2C_MUX_CH_VOL_MONITOR 0xa - -#define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv" -#ifndef CONFIG_SPL_BUILD -#define CONFIG_VID -#endif -#define CONFIG_VOL_MONITOR_IR36021_SET -#define CONFIG_VOL_MONITOR_IR36021_READ -/* The lowest and highest voltage allowed for T208xRDB */ -#define VDD_MV_MIN 819 -#define VDD_MV_MAX 1212 - -/* - * RapidIO - */ -#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull -#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 -#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull -#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ -/* - * for slave u-boot IMAGE instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull -/* - * for slave UCODE and ENV instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ - -/* slave core release by master*/ -#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 -#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ - -/* - * SRIO_PCIE_BOOT - SLAVE - */ -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE -#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 -#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) -#endif - -/* - * eSPI - Enhanced SPI - */ - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_PCIE1 /* PCIE controller 1 */ -#define CONFIG_PCIE2 /* PCIE controller 2 */ -#define CONFIG_PCIE3 /* PCIE controller 3 */ -#define CONFIG_PCIE4 /* PCIE controller 4 */ -#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ -/* controller 1, direct to uli, tgtid 3, Base address 20000 */ -#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull -#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull - -/* controller 2, Slot 2, tgtid 2, Base address 201000 */ -#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull -#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull - -/* controller 3, Slot 1, tgtid 1, Base address 202000 */ -#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 -#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull -#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 -#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull - -/* controller 4, Base address 203000 */ -#define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 -#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull -#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull - -#ifdef CONFIG_PCI -#if !defined(CONFIG_DM_PCI) -#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ -#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ -#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ -#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ -#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ -#define CONFIG_PCI_INDIRECT_BRIDGE -#endif -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#endif - -/* Qman/Bman */ -#ifndef CONFIG_NOBQFMAN -#define CONFIG_SYS_BMAN_NUM_PORTALS 18 -#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 -#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull -#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 -#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 -#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 -#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE -#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ - CONFIG_SYS_BMAN_CENA_SIZE) -#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 -#define CONFIG_SYS_QMAN_NUM_PORTALS 18 -#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 -#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull -#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 -#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 -#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 -#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE -#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ - CONFIG_SYS_QMAN_CENA_SIZE) -#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 - -#define CONFIG_SYS_DPAA_FMAN -#define CONFIG_SYS_DPAA_PME -#define CONFIG_SYS_PMAN -#define CONFIG_SYS_DPAA_DCE -#define CONFIG_SYS_DPAA_RMAN /* RMan */ -#define CONFIG_SYS_INTERLAKEN - -/* Default address of microcode for the Linux Fman driver */ -#if defined(CONFIG_SPIFLASH) -/* - * env is stored at 0x100000, sector size is 0x10000, ucode is stored after - * env, so we got 0x110000. - */ -#define CONFIG_SYS_FMAN_FW_ADDR 0x110000 -#define CONFIG_CORTINA_FW_ADDR 0x120000 - -#elif defined(CONFIG_SDCARD) -/* - * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is - * about 1MB (2048 blocks), Env is stored after the image, and the env size is - * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. - */ -#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) -#define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) - -#elif defined(CONFIG_MTD_RAW_NAND) -#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) -#define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) -#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) -/* - * Slave has no ucode locally, it can fetch this from remote. When implementing - * in two corenet boards, slave's ucode could be stored in master's memory - * space, the address can be mapped from slave TLB->slave LAW-> - * slave SRIO or PCIE outbound window->master inbound window-> - * master LAW->the ucode address in master's memory space. - */ -#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 -#define CONFIG_CORTINA_FW_ADDR 0xFFE10000 -#else -#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 -#define CONFIG_CORTINA_FW_ADDR 0xEFE00000 -#endif -#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 -#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) -#endif /* CONFIG_NOBQFMAN */ - -#ifdef CONFIG_SYS_DPAA_FMAN -#define CONFIG_CORTINA_FW_LENGTH 0x40000 -#define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ -#define RGMII_PHY2_ADDR 0x02 -#define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ -#define CORTINA_PHY_ADDR2 0x0d -#define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ -#define FM1_10GEC4_PHY_ADDR 0x01 -#endif - -#ifdef CONFIG_FMAN_ENET -#define CONFIG_ETHPRIME "FM1@DTSEC3" -#endif - -/* - * SATA - */ -#ifdef CONFIG_FSL_SATA_V2 -#define CONFIG_SYS_SATA_MAX_DEVICE 2 -#define CONFIG_SATA1 -#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR -#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA -#define CONFIG_SATA2 -#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR -#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA -#define CONFIG_LBA48 -#endif - -/* - * USB - */ -#ifdef CONFIG_USB_EHCI_HCD -#define CONFIG_USB_EHCI_FSL -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_HAS_FSL_DR_USB -#endif - -/* - * SDHC - */ -#ifdef CONFIG_MMC -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR -#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT -#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 -#endif - -/* - * Dynamic MTD Partition support with mtdparts - */ - -/* - * Environment - */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#ifdef CONFIG_CMD_KGDB -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ - -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 1000000 -#define __USB_PHY_TYPE utmi - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "hwconfig=fsl_ddr:" \ - "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ - "bank_intlv=auto;" \ - "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ - "netdev=eth0\0" \ - "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ - "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ - "tftpflash=tftpboot $loadaddr $uboot && " \ - "protect off $ubootaddr +$filesize && " \ - "erase $ubootaddr +$filesize && " \ - "cp.b $loadaddr $ubootaddr $filesize && " \ - "protect on $ubootaddr +$filesize && " \ - "cmp.b $loadaddr $ubootaddr $filesize\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ - "fdtaddr=1e00000\0" \ - "fdtfile=t2080rdb/t2080rdb.dtb\0" \ - "bdev=sda3\0" - -/* - * For emulation this causes u-boot to jump to the start of the - * proof point app code automatically - */ -#define CONFIG_PROOF_POINTS \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "cpu 1 release 0x29000000 - - -;" \ - "cpu 2 release 0x29000000 - - -;" \ - "cpu 3 release 0x29000000 - - -;" \ - "cpu 4 release 0x29000000 - - -;" \ - "cpu 5 release 0x29000000 - - -;" \ - "cpu 6 release 0x29000000 - - -;" \ - "cpu 7 release 0x29000000 - - -;" \ - "go 0x29000000" - -#define CONFIG_HVBOOT \ - "setenv bootargs config-addr=0x60000000; " \ - "bootm 0x01000000 - 0x00f00000" - -#define CONFIG_ALU \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "cpu 1 release 0x01000000 - - -;" \ - "cpu 2 release 0x01000000 - - -;" \ - "cpu 3 release 0x01000000 - - -;" \ - "cpu 4 release 0x01000000 - - -;" \ - "cpu 5 release 0x01000000 - - -;" \ - "cpu 6 release 0x01000000 - - -;" \ - "cpu 7 release 0x01000000 - - -;" \ - "go 0x01000000" - -#define CONFIG_LINUX \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "setenv ramdiskaddr 0x02000000;" \ - "setenv fdtaddr 0x00c00000;" \ - "setenv loadaddr 0x1000000;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_HDBOOT \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_LINUX - -#include <asm/fsl_secure_boot.h> - -#endif /* __T2080RDB_H */