This board has not been converted to generic board by the deadline. Remove it.
Signed-off-by: Simon Glass sjg@chromium.org ---
arch/arm/Kconfig | 5 - board/scb9328/Kconfig | 12 -- board/scb9328/MAINTAINERS | 6 - board/scb9328/Makefile | 9 -- board/scb9328/flash.c | 310 ----------------------------------------- board/scb9328/intel.h | 78 ----------- board/scb9328/lowlevel_init.S | 188 ------------------------- board/scb9328/scb9328.c | 54 -------- configs/scb9328_defconfig | 7 - include/configs/scb9328.h | 312 ------------------------------------------ 10 files changed, 981 deletions(-) delete mode 100644 board/scb9328/Kconfig delete mode 100644 board/scb9328/MAINTAINERS delete mode 100644 board/scb9328/Makefile delete mode 100644 board/scb9328/flash.c delete mode 100644 board/scb9328/intel.h delete mode 100644 board/scb9328/lowlevel_init.S delete mode 100644 board/scb9328/scb9328.c delete mode 100644 configs/scb9328_defconfig delete mode 100644 include/configs/scb9328.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 2636db3..0ab0c24 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -69,10 +69,6 @@ choice config ARCH_AT91 bool "Atmel AT91"
-config TARGET_SCB9328 - bool "Support scb9328" - select CPU_ARM920T - config TARGET_VCMA9 bool "Support VCMA9" select CPU_ARM920T @@ -874,7 +870,6 @@ source "board/phytec/pcm051/Kconfig" source "board/ppcag/bg0900/Kconfig" source "board/samsung/smdk2410/Kconfig" source "board/sandisk/sansa_fuze_plus/Kconfig" -source "board/scb9328/Kconfig" source "board/schulercontrol/sc_sps_1/Kconfig" source "board/siemens/draco/Kconfig" source "board/siemens/pxm2/Kconfig" diff --git a/board/scb9328/Kconfig b/board/scb9328/Kconfig deleted file mode 100644 index 68e99ea..0000000 --- a/board/scb9328/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_SCB9328 - -config SYS_BOARD - default "scb9328" - -config SYS_SOC - default "imx" - -config SYS_CONFIG_NAME - default "scb9328" - -endif diff --git a/board/scb9328/MAINTAINERS b/board/scb9328/MAINTAINERS deleted file mode 100644 index 0917266..0000000 --- a/board/scb9328/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -SCB9328 BOARD -M: Torsten Koschorrek koschorrek@synertronixx.de -S: Maintained -F: board/scb9328/ -F: include/configs/scb9328.h -F: configs/scb9328_defconfig diff --git a/board/scb9328/Makefile b/board/scb9328/Makefile deleted file mode 100644 index 0b08f1a..0000000 --- a/board/scb9328/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := scb9328.o flash.o -obj-y += lowlevel_init.o diff --git a/board/scb9328/flash.c b/board/scb9328/flash.c deleted file mode 100644 index 73bfa00..0000000 --- a/board/scb9328/flash.c +++ /dev/null @@ -1,310 +0,0 @@ -/* - * Copyright (C) 2003 ETC s.r.o. - * - * This code was inspired by Marius Groeger and Kyle Harris code - * available in other board ports for U-Boot - * - * SPDX-License-Identifier: GPL-2.0+ - * - * Written by Peter Figuli peposh@etc.sk, 2003. - */ - -#include <common.h> -#include "intel.h" - - -/* - * This code should handle CFI FLASH memory device. This code is very - * minimalistic approach without many essential error handling code as well. - * Because U-Boot actually is missing smart handling of FLASH device, - * we just set flash_id to anything else to FLASH_UNKNOW, so common code - * can call us without any restrictions. - * TODO: Add CFI Query, to be able to determine FLASH device. - * TODO: Add error handling code - * NOTE: This code was tested with BUS_WIDTH 4 and ITERLEAVE 2 only, but - * hopefully may work with other configurations. - */ - -#if ( SCB9328_FLASH_BUS_WIDTH == 1 ) -# define FLASH_BUS vu_char -# define FLASH_BUS_RET u_char -# if ( SCB9328_FLASH_INTERLEAVE == 1 ) -# define FLASH_CMD( x ) x -# else -# error "With 8bit bus only one chip is allowed" -# endif - - -#elif ( SCB9328_FLASH_BUS_WIDTH == 2 ) -# define FLASH_BUS vu_short -# define FLASH_BUS_RET u_short -# if ( SCB9328_FLASH_INTERLEAVE == 1 ) -# define FLASH_CMD( x ) x -# elif ( SCB9328_FLASH_INTERLEAVE == 2 ) -# define FLASH_CMD( x ) (( x << 8 )| x ) -# else -# error "With 16bit bus only 1 or 2 chip(s) are allowed" -# endif - - -#elif ( SCB9328_FLASH_BUS_WIDTH == 4 ) -# define FLASH_BUS vu_long -# define FLASH_BUS_RET u_long -# if ( SCB9328_FLASH_INTERLEAVE == 1 ) -# define FLASH_CMD( x ) x -# elif ( SCB9328_FLASH_INTERLEAVE == 2 ) -# define FLASH_CMD( x ) (( x << 16 )| x ) -# elif ( SCB9328_FLASH_INTERLEAVE == 4 ) -# define FLASH_CMD( x ) (( x << 24 )|( x << 16 ) ( x << 8 )| x ) -# else -# error "With 32bit bus only 1,2 or 4 chip(s) are allowed" -# endif - -#else -# error "Flash bus width might be 1,2,4 for 8,16,32 bit configuration" -#endif - - -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; - -static FLASH_BUS_RET flash_status_reg (void) -{ - - FLASH_BUS *addr = (FLASH_BUS *) 0; - - /* cppcheck-suppress nullPointer */ - *addr = FLASH_CMD (CFI_INTEL_CMD_READ_STATUS_REGISTER); - - /* cppcheck-suppress nullPointer */ - return *addr; -} - -static int flash_ready (ulong timeout) -{ - int ok = 1; - ulong start; - - start = get_timer(0); - while ((flash_status_reg () & FLASH_CMD (CFI_INTEL_SR_READY)) != - FLASH_CMD (CFI_INTEL_SR_READY)) { - if (get_timer(start) > timeout && timeout != 0) { - ok = 0; - break; - } - } - return ok; -} - -#if ( CONFIG_SYS_MAX_FLASH_BANKS != 1 ) -# error "SCB9328 platform has only one flash bank!" -#endif - - -ulong flash_init (void) -{ - int i; - unsigned long address = SCB9328_FLASH_BASE; - - flash_info[0].size = SCB9328_FLASH_BANK_SIZE; - flash_info[0].sector_count = CONFIG_SYS_MAX_FLASH_SECT; - flash_info[0].flash_id = INTEL_MANUFACT; - memset (flash_info[0].protect, 0, CONFIG_SYS_MAX_FLASH_SECT); - - for (i = 0; i < CONFIG_SYS_MAX_FLASH_SECT; i++) { - flash_info[0].start[i] = address; -#ifdef SCB9328_FLASH_UNLOCK - /* Some devices are hw locked after start. */ - *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_LOCK_SETUP); - *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_UNLOCK_BLOCK); - flash_ready (0); - *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY); -#endif - address += SCB9328_FLASH_SECT_SIZE; - } - - flash_protect (FLAG_PROTECT_SET, - CONFIG_SYS_FLASH_BASE, - CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, - &flash_info[0]); - - flash_protect (FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]); - - return SCB9328_FLASH_BANK_SIZE; -} - -void flash_print_info (flash_info_t * info) -{ - int i; - - printf (" Intel vendor\n"); - printf (" Size: %ld MB in %d Sectors\n", - info->size >> 20, info->sector_count); - - printf (" Sector Start Addresses:"); - for (i = 0; i < info->sector_count; i++) { - if (!(i % 5)) { - printf ("\n"); - } - - printf (" %08lX%s", info->start[i], - info->protect[i] ? " (RO)" : " "); - } - printf ("\n"); -} - - -int flash_erase (flash_info_t * info, int s_first, int s_last) -{ - int flag, non_protected = 0, sector; - int rc = ERR_OK; - - FLASH_BUS *address; - - for (sector = s_first; sector <= s_last; sector++) { - if (!info->protect[sector]) { - non_protected++; - } - } - - if (!non_protected) { - return ERR_PROTECTED; - } - - /* - * Disable interrupts which might cause a timeout - * here. Remember that our exception vectors are - * at address 0 in the flash, and we don't want a - * (ticker) exception to happen while the flash - * chip is in programming mode. - */ - flag = disable_interrupts (); - - - /* Start erase on unprotected sectors */ - for (sector = s_first; sector <= s_last && !ctrlc (); sector++) { - if (info->protect[sector]) { - printf ("Protected sector %2d skipping...\n", sector); - continue; - } else { - printf ("Erasing sector %2d ... ", sector); - } - - address = (FLASH_BUS *) (info->start[sector]); - - *address = FLASH_CMD (CFI_INTEL_CMD_BLOCK_ERASE); - *address = FLASH_CMD (CFI_INTEL_CMD_CONFIRM); - if (flash_ready (CONFIG_SYS_FLASH_ERASE_TOUT)) { - *address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER); - printf ("ok.\n"); - } else { - *address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND); - rc = ERR_TIMOUT; - printf ("timeout! Aborting...\n"); - break; - } - *address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY); - } - if (ctrlc ()) - printf ("User Interrupt!\n"); - - /* allow flash to settle - wait 10 ms */ - udelay_masked (10000); - if (flag) { - enable_interrupts (); - } - - return rc; -} - -static int write_data (flash_info_t * info, ulong dest, FLASH_BUS data) -{ - FLASH_BUS *address = (FLASH_BUS *) dest; - int rc = ERR_OK; - int flag; - - /* Check if Flash is (sufficiently) erased */ - if ((*address & data) != data) { - return ERR_NOT_ERASED; - } - - /* - * Disable interrupts which might cause a timeout - * here. Remember that our exception vectors are - * at address 0 in the flash, and we don't want a - * (ticker) exception to happen while the flash - * chip is in programming mode. - */ - - flag = disable_interrupts (); - - *address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER); - *address = FLASH_CMD (CFI_INTEL_CMD_PROGRAM1); - *address = data; - - if (!flash_ready (CONFIG_SYS_FLASH_WRITE_TOUT)) { - *address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND); - rc = ERR_TIMOUT; - printf ("timeout! Aborting...\n"); - } - - *address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY); - if (flag) { - enable_interrupts (); - } - - return rc; -} - -int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) -{ - ulong read_addr, write_addr; - FLASH_BUS data; - int i, result = ERR_OK; - - - read_addr = addr & ~(sizeof (FLASH_BUS) - 1); - write_addr = read_addr; - if (read_addr != addr) { - data = 0; - for (i = 0; i < sizeof (FLASH_BUS); i++) { - if (read_addr < addr || cnt == 0) { - data |= *((uchar *) read_addr) << i * 8; - } else { - data |= (*src++) << i * 8; - cnt--; - } - read_addr++; - } - if ((result = write_data (info, write_addr, data)) != ERR_OK) { - return result; - } - write_addr += sizeof (FLASH_BUS); - } - for (; cnt >= sizeof (FLASH_BUS); cnt -= sizeof (FLASH_BUS)) { - if ((result = write_data (info, write_addr, - *((FLASH_BUS *) src))) != ERR_OK) { - return result; - } - write_addr += sizeof (FLASH_BUS); - src += sizeof (FLASH_BUS); - } - if (cnt > 0) { - read_addr = write_addr; - data = 0; - for (i = 0; i < sizeof (FLASH_BUS); i++) { - if (cnt > 0) { - data |= (*src++) << i * 8; - cnt--; - } else { - data |= *((uchar *) read_addr) << i * 8; - } - read_addr++; - } - if ((result = write_data (info, write_addr, data)) != 0) { - return result; - } - } - return ERR_OK; -} diff --git a/board/scb9328/intel.h b/board/scb9328/intel.h deleted file mode 100644 index 5596d27..0000000 --- a/board/scb9328/intel.h +++ /dev/null @@ -1,78 +0,0 @@ -/* - * Copyright (C) 2002 ETC s.r.o. - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - * - * Written by Marcel Telka marcel@telka.sk, 2002. - * - * Documentation: - * [1] Intel Corporation, "3 Volt Intel Strata Flash Memory 28F128J3A, 28F640J3A, - * 28F320J3A (x8/x16)", April 2002, Order Number: 290667-011 - * [2] Intel Corporation, "3 Volt Synchronous Intel Strata Flash Memory 28F640K3, 28F640K18, - * 28F128K3, 28F128K18, 28F256K3, 28F256K18 (x16)", June 2002, Order Number: 290737-005 - * - * This file is taken from OpenWinCE project hosted by SourceForge.net - * - */ - -#ifndef FLASH_INTEL_H -#define FLASH_INTEL_H - -#include <common.h> - -/* Intel CFI commands - see Table 4. in [1] and Table 3. in [2] */ - -#define CFI_INTEL_CMD_READ_ARRAY 0xFF /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_READ_IDENTIFIER 0x90 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_READ_QUERY 0x98 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_READ_STATUS_REGISTER 0x70 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_CLEAR_STATUS_REGISTER 0x50 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_PROGRAM1 0x40 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_PROGRAM2 0x10 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_WRITE_TO_BUFFER 0xE8 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_CONFIRM 0xD0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_BLOCK_ERASE 0x20 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_SUSPEND 0xB0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_RESUME 0xD0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_LOCK_SETUP 0x60 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_LOCK_BLOCK 0x01 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_UNLOCK_BLOCK 0xD0 /* 28FxxxJ3A - unlocks all blocks, 28FFxxxK3, 28FxxxK18 */ -#define CFI_INTEL_CMD_LOCK_DOWN_BLOCK 0x2F /* 28FxxxK3, 28FxxxK18 */ - -/* Intel CFI Status Register bits - see Table 6. in [1] and Table 7. in [2] */ - -#define CFI_INTEL_SR_READY 1 << 7 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_SR_ERASE_SUSPEND 1 << 6 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_SR_ERASE_ERROR 1 << 5 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_SR_PROGRAM_ERROR 1 << 4 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_SR_VPEN_ERROR 1 << 3 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_SR_PROGRAM_SUSPEND 1 << 2 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_SR_BLOCK_LOCKED 1 << 1 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ -#define CFI_INTEL_SR_BEFP 1 << 0 /* 28FxxxK3, 28FxxxK18 */ - -/* Intel flash device ID codes for 28FxxxJ3A - see Table 5. in [1] */ - -#define CFI_CHIP_INTEL_28F320J3A 0x0016 -#define CFI_CHIPN_INTEL_28F320J3A "28F320J3A" -#define CFI_CHIP_INTEL_28F640J3A 0x0017 -#define CFI_CHIPN_INTEL_28F640J3A "28F640J3A" -#define CFI_CHIP_INTEL_28F128J3A 0x0018 -#define CFI_CHIPN_INTEL_28F128J3A "28F128J3A" - -/* Intel flash device ID codes for 28FxxxK3 and 28FxxxK18 - see Table 8. in [2] */ - -#define CFI_CHIP_INTEL_28F640K3 0x8801 -#define CFI_CHIPN_INTEL_28F640K3 "28F640K3" -#define CFI_CHIP_INTEL_28F128K3 0x8802 -#define CFI_CHIPN_INTEL_28F128K3 "28F128K3" -#define CFI_CHIP_INTEL_28F256K3 0x8803 -#define CFI_CHIPN_INTEL_28F256K3 "28F256K3" -#define CFI_CHIP_INTEL_28F640K18 0x8805 -#define CFI_CHIPN_INTEL_28F640K18 "28F640K18" -#define CFI_CHIP_INTEL_28F128K18 0x8806 -#define CFI_CHIPN_INTEL_28F128K18 "28F128K18" -#define CFI_CHIP_INTEL_28F256K18 0x8807 -#define CFI_CHIPN_INTEL_28F256K18 "28F256K18" - -#endif /* FLASH_INTEL_H */ diff --git a/board/scb9328/lowlevel_init.S b/board/scb9328/lowlevel_init.S deleted file mode 100644 index d572724..0000000 --- a/board/scb9328/lowlevel_init.S +++ /dev/null @@ -1,188 +0,0 @@ -/* - * Copyright (C) 2004 Sascha Hauer, Synertronixx GmbH - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <config.h> -#include <asm/arch/imx-regs.h> - -.globl lowlevel_init -lowlevel_init: - - mov r10, lr - -/* Change PERCLK1DIV to 14 ie 14+1 */ - ldr r0, =PCDR - ldr r1, =CONFIG_SYS_PCDR_VAL - str r1, [r0] - -/* set MCU PLL Control Register 0 */ - - ldr r0, =MPCTL0 - ldr r1, =CONFIG_SYS_MPCTL0_VAL - str r1, [r0] - -/* set mpll restart bit */ - ldr r0, =CSCR - ldr r1, [r0] - orr r1,r1,#(1<<21) - str r1, [r0] - - mov r2,#0x10 -1: - mov r3,#0x2000 -2: - subs r3,r3,#1 - bne 2b - - subs r2,r2,#1 - bne 1b - -/* set System PLL Control Register 0 */ - - ldr r0, =SPCTL0 - ldr r1, =CONFIG_SYS_SPCTL0_VAL - str r1, [r0] - -/* set spll restart bit */ - ldr r0, =CSCR - ldr r1, [r0] - orr r1,r1,#(1<<22) - str r1, [r0] - - mov r2,#0x10 -1: - mov r3,#0x2000 -2: - subs r3,r3,#1 - bne 2b - - subs r2,r2,#1 - bne 1b - - ldr r0, =CSCR - ldr r1, =CONFIG_SYS_CSCR_VAL - str r1, [r0] - -/* I have now read the ARM920 DataSheet back-to-Back, and have stumbled upon - *this..... - * - * It would appear that from a Cold-Boot the ARM920T enters "FastBus" mode CP15 - * register 1, this stops it using the output of the PLL and thus runs at the - * slow rate. Unless you place the Core into "Asynch" mode, the CPU will never - * use the value set in the CM_OSC registers...regardless of what you set it - * too! Thus, although i thought i was running at 140MHz, i'm actually running - * at 40!.. - - * Slapping this into my bootloader does the trick... - - * MRC p15,0,r0,c1,c0,0 ; read core configuration register - * ORR r0,r0,#0xC0000000 ; set asynchronous clocks and not fastbus mode - * MCR p15,0,r0,c1,c0,0 ; write modified value to core configuration - * register - */ - MRC p15,0,r0,c1,c0,0 - ORR r0,r0,#0xC0000000 - MCR p15,0,r0,c1,c0,0 - - ldr r0, =GPR(0) - ldr r1, =CONFIG_SYS_GPR_A_VAL - str r1, [r0] - - ldr r0, =GIUS(0) - ldr r1, =CONFIG_SYS_GIUS_A_VAL - str r1, [r0] - -/* CS3 becomes CS3 by clearing reset default bit 1 in FMCR */ - - ldr r0, =FMCR - ldr r1, =CONFIG_SYS_FMCR_VAL - str r1, [r0] - - ldr r0, =CS0U - ldr r1, =CONFIG_SYS_CS0U_VAL - str r1, [r0] - - ldr r0, =CS0L - ldr r1, =CONFIG_SYS_CS0L_VAL - str r1, [r0] - - ldr r0, =CS1U - ldr r1, =CONFIG_SYS_CS1U_VAL - str r1, [r0] - - ldr r0, =CS1L - ldr r1, =CONFIG_SYS_CS1L_VAL - str r1, [r0] - - ldr r0, =CS2U - ldr r1, =CONFIG_SYS_CS2U_VAL - str r1, [r0] - - ldr r0, =CS2L - ldr r1, =CONFIG_SYS_CS2L_VAL - str r1, [r0] - - ldr r0, =CS3U - ldr r1, =CONFIG_SYS_CS3U_VAL - str r1, [r0] - - ldr r0, =CS3L - ldr r1, =CONFIG_SYS_CS3L_VAL - str r1, [r0] - - ldr r0, =CS4U - ldr r1, =CONFIG_SYS_CS4U_VAL - str r1, [r0] - - ldr r0, =CS4L - ldr r1, =CONFIG_SYS_CS4L_VAL - str r1, [r0] - - ldr r0, =CS5U - ldr r1, =CONFIG_SYS_CS5U_VAL - str r1, [r0] - - ldr r0, =CS5L - ldr r1, =CONFIG_SYS_CS5L_VAL - str r1, [r0] - -/* SDRAM Setup */ - - ldr r0, =SDCTL0 - ldr r1, =PRECHARGE_CMD - str r1, [r0] - - ldr r0, =0x08200000 - ldr r1, =0x0 /* Issue Precharge all Command */ - str r1, [r0] - - ldr r0, =SDCTL0 - ldr r1, =AUTOREFRESH_CMD - str r1, [r0] - - ldr r0, =0x08000000 - ldr r1, =0x0 /* Issue AutoRefresh Command */ - str r1, [r0] - str r1, [r0] - str r1, [r0] - str r1, [r0] - str r1, [r0] - str r1, [r0] - str r1, [r0] - str r1, [r0] - - ldr r0, =SDCTL0 - ldr r1, =0xb10a8300 - str r1, [r0] - - ldr r0, =0x08223000 /* CAS Latency 2 */ - ldr r1, =0x0 /* Issue Mode Register Command, Burst Length = 8 */ - str r1, [r0] - - ldr r0, =SDCTL0 - ldr r1, =0x810a8200 /* Set to Normal Mode CAS 2 */ - str r1, [r0] - - mov pc,r10 diff --git a/board/scb9328/scb9328.c b/board/scb9328/scb9328.c deleted file mode 100644 index 3463f52..0000000 --- a/board/scb9328/scb9328.c +++ /dev/null @@ -1,54 +0,0 @@ -/* - * Copyright (C) 2004 Sascha Hauer, Synertronixx GmbH - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <netdev.h> - -DECLARE_GLOBAL_DATA_PTR; - -int board_init (void) -{ - gd->bd->bi_arch_number = MACH_TYPE_SCB9328; - gd->bd->bi_boot_params = 0x08000100; - - return 0; -} - -int dram_init (void) -{ - /* dram_init must store complete ramsize in gd->ram_size */ - gd->ram_size = get_ram_size((void *)SCB9328_SDRAM_1, - SCB9328_SDRAM_1_SIZE); - - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = SCB9328_SDRAM_1; - gd->bd->bi_dram[0].size = SCB9328_SDRAM_1_SIZE; -} - -/** - * show_boot_progress: - indicate state of the boot process - * - * @param status: Status number - see README for details. - * - * The CSB226 does only have 3 LEDs, so we switch them on at the most - * important states (1, 5, 15). - */ - -void show_boot_progress (int status) -{ - return; -} - -#ifdef CONFIG_DRIVER_DM9000 -int board_eth_init(bd_t *bis) -{ - return dm9000_initialize(bis); -} -#endif diff --git a/configs/scb9328_defconfig b/configs/scb9328_defconfig deleted file mode 100644 index c9c5034..0000000 --- a/configs/scb9328_defconfig +++ /dev/null @@ -1,7 +0,0 @@ -CONFIG_ARM=y -CONFIG_TARGET_SCB9328=y -# CONFIG_CMD_CONSOLE is not set -# CONFIG_CMD_LOADS is not set -# CONFIG_CMD_SOURCE is not set -# CONFIG_CMD_SETEXPR is not set -CONFIG_SYS_PROMPT="scb9328> " diff --git a/include/configs/scb9328.h b/include/configs/scb9328.h deleted file mode 100644 index d4ffb46..0000000 --- a/include/configs/scb9328.h +++ /dev/null @@ -1,312 +0,0 @@ -/* - * Copyright (C) 2003 ETC s.r.o. - * - * SPDX-License-Identifier: GPL-2.0+ - * Written by Peter Figuli peposh@etc.sk, 2003. - * - * 2003/13/06 Initial MP10 Support copied from wepep250 - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IMX 1 /* This is a Motorola MC9328MXL Chip */ -#define CONFIG_SCB9328 1 /* on a scb9328tronix board */ - -#define CONFIG_IMX_SERIAL -#define CONFIG_IMX_SERIAL1 -/* - * Select serial console configuration - */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP - -/* - * Boot options. Setting delay to -1 stops autostart count down. - * NOTE: Sending parameters to kernel depends on kernel version and - * 2.4.19-rmk6-pxa1 patch used while my u-boot coding didn't accept - * parameters at all! Do not get confused by them so. - */ -#define CONFIG_BOOTDELAY -1 -#define CONFIG_BOOTARGS "console=ttySMX0,115200n8 root=/dev/mtdblock3 rootfstype=jffs2 mtdparts=scb9328_flash:128k(U-boot)ro,128k(U-boot_env),1m(kernel),4m(root),4m(fs) eval_board=evk9328" -#define CONFIG_BOOTCOMMAND "bootm 10040000" -#define CONFIG_SHOW_BOOT_PROGRESS -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 10.10.10.9 -#define CONFIG_SERVERIP 10.10.10.10 - -/* - * General options for u-boot. Modify to save memory foot print - */ -#define CONFIG_SYS_LONGHELP /* undef saves memory */ -#define CONFIG_SYS_CBSIZE 256 /* console I/O buffer */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size */ -#define CONFIG_SYS_MAXARGS 16 /* max command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* boot args buf size */ - -#define CONFIG_SYS_MEMTEST_START 0x08100000 /* memtest test area */ -#define CONFIG_SYS_MEMTEST_END 0x08F00000 - -#define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */ - -#define CONFIG_BAUDRATE 115200 -/* - * Definitions related to passing arguments to kernel. - */ -#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */ -#define CONFIG_INITRD_TAG 1 /* send initrd params */ - -/* - * Malloc pool need to host env + 128 Kb reserve for other allocations. - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128<<10) ) - -/* SDRAM Setup Values -0x910a8300 Precharge Command CAS 3 -0x910a8200 Precharge Command CAS 2 - -0xa10a8300 AutoRefresh Command CAS 3 -0xa10a8200 Set AutoRefresh Command CAS 2 */ - -#define PRECHARGE_CMD 0x910a8200 -#define AUTOREFRESH_CMD 0xa10a8200 - -/* - * SDRAM Memory Map - */ -/* SH FIXME */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */ -#define SCB9328_SDRAM_1 0x08000000 /* SDRAM bank #1 */ -#define SCB9328_SDRAM_1_SIZE 0x01000000 /* 16 MB */ - -#define CONFIG_SYS_TEXT_BASE 0x10000000 - -#define CONFIG_SYS_SDRAM_BASE SCB9328_SDRAM_1 -#define CONFIG_SYS_INIT_SP_ADDR (SCB9328_SDRAM_1 + 0xf00000) - -/* - * Configuration for FLASH memory for the Synertronixx board - */ - -/* #define SCB9328_FLASH_32M */ - -/* 32MB */ -#ifdef SCB9328_FLASH_32M -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */ -#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */ -#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */ -#define SCB9328_FLASH_BANK_SIZE 0x02000000 /* size of one flash bank */ -#define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */ -#define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */ -#define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */ -#else - -/* 16MB */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* number of sector in FLASH bank */ -#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */ -#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */ -#define SCB9328_FLASH_BANK_SIZE 0x01000000 /* size of one flash bank */ -#define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */ -#define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */ -#define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */ -#endif /* SCB9328_FLASH_32M */ - -/* This should be defined if CFI FLASH device is present. Actually benefit - is not so clear to me. In other words we can provide more informations - to user, but this expects more complex flash handling we do not provide - now.*/ -#undef CONFIG_SYS_FLASH_CFI - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* timeout for Erase operation */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 240000 /* timeout for Write operation */ - -#define CONFIG_SYS_FLASH_BASE SCB9328_FLASH_BASE - -/* - * This is setting for JFFS2 support in u-boot. - * Right now there is no gain for user, but later on booting kernel might be - * possible. Consider using XIP kernel running from flash to save RAM - * footprint. - * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. - */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 5 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 - -/* - * Environment setup. Definitions of monitor location and size with - * definition of environment setup ends up in 2 possibilities. - * 1. Embeded environment - in u-boot code is space for environment - * 2. Environment is read from predefined sector of flash - * Right now we support 2. possiblity, but expecting no env placed - * on mentioned address right now. This also needs to provide whole - * sector for it - for us 256Kb is really waste of memory. U-boot uses - * default env. and until kernel parameters could be sent to kernel - * env. has no sense to us. - */ - -/* Setup for PA23 which is Reset Default PA23 but has to become - CS5 */ - -#define CONFIG_SYS_GPR_A_VAL 0x00800000 -#define CONFIG_SYS_GIUS_A_VAL 0x0043fffe - -#define CONFIG_SYS_MONITOR_BASE 0x10000000 -#define CONFIG_SYS_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0x10020000 /* absolute address for now */ -#define CONFIG_ENV_SIZE 0x20000 - -#define CONFIG_ENV_OVERWRITE 1 /* env is not writable now */ - -/* - * CSxU_VAL: - * 63| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x|32 - * |DTACK_SEL|0|BCD | BCS | PSZ|PME|SYNC| DOL | CNC| WSC | 0| WWS | EDC | - * - * CSxL_VAL: - * 31| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x| 0 - * | OEA | OEN | WEA | WEN | CSA |EBC| DSZ | 0|SP|0|WP| 0 0|PA|CSEN| - */ - -#define CONFIG_SYS_CS0U_VAL 0x000F2000 -#define CONFIG_SYS_CS0L_VAL 0x11110d01 -#define CONFIG_SYS_CS1U_VAL 0x000F0a00 -#define CONFIG_SYS_CS1L_VAL 0x11110601 -#define CONFIG_SYS_CS2U_VAL 0x0 -#define CONFIG_SYS_CS2L_VAL 0x0 - -#define CONFIG_SYS_CS3U_VAL 0x000FFFFF -#define CONFIG_SYS_CS3L_VAL 0x00000303 - -#define CONFIG_SYS_CS4U_VAL 0x000F0a00 -#define CONFIG_SYS_CS4L_VAL 0x11110301 - -/* CNC == 3 too long - #define CONFIG_SYS_CS5U_VAL 0x0000C210 */ - -/* #define CONFIG_SYS_CS5U_VAL 0x00008400 - mal laenger mahcen, ob der bei 150MHz laenger haelt dann und - kaum langsamer ist */ -/* #define CONFIG_SYS_CS5U_VAL 0x00009400 - #define CONFIG_SYS_CS5L_VAL 0x11010D03 */ - -#define CONFIG_SYS_CS5U_VAL 0x00008400 -#define CONFIG_SYS_CS5L_VAL 0x00000D03 - -#define CONFIG_DRIVER_DM9000 1 -#define CONFIG_DM9000_BASE 0x16000000 -#define DM9000_IO CONFIG_DM9000_BASE -#define DM9000_DATA (CONFIG_DM9000_BASE+4) - -/* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1) - f_ref=16,777MHz - - 0x002a141f: 191,9944MHz - 0x040b2007: 144MHz - 0x042a141f: 96MHz - 0x0811140d: 64MHz - 0x040e200e: 150MHz - 0x00321431: 200MHz - - 0x08001800: 64MHz mit 16er Quarz - 0x04001800: 96MHz mit 16er Quarz - 0x04002400: 144MHz mit 16er Quarz - - 31 |x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x| 0 - |XXX|--PD---|-------MFD---------|XXX|--MFI--|-----MFN-----------| */ - -#define CPU200 - -#ifdef CPU200 -#define CONFIG_SYS_MPCTL0_VAL 0x00321431 -#else -#define CONFIG_SYS_MPCTL0_VAL 0x040e200e -#endif - -/* #define BUS64 */ -#define BUS72 - -#ifdef BUS72 -#define CONFIG_SYS_SPCTL0_VAL 0x04002400 -#endif - -#ifdef BUS96 -#define CONFIG_SYS_SPCTL0_VAL 0x04001800 -#endif - -#ifdef BUS64 -#define CONFIG_SYS_SPCTL0_VAL 0x08001800 -#endif - -/* Das ist der BCLK Divider, der aus der System PLL - BCLK und HCLK erzeugt: - 31 | xxxx xxxx xxxx xxxx xx10 11xx xxxx xxxx | 0 - 0x2f008403 : 192MHz/2=96MHz, 144MHz/2=72MHz PRESC=1->BCLKDIV=2 - 0x2f008803 : 192MHz/3=64MHz, 240MHz/3=80MHz PRESC=1->BCLKDIV=2 - 0x2f001003 : 192MHz/5=38,4MHz - 0x2f000003 : 64MHz/1 - Bit 22: SPLL Restart - Bit 21: MPLL Restart */ - -#ifdef BUS64 -#define CONFIG_SYS_CSCR_VAL 0x2f030003 -#endif - -#ifdef BUS72 -#define CONFIG_SYS_CSCR_VAL 0x2f030403 -#endif - -/* - * Well this has to be defined, but on the other hand it is used differently - * one may expect. For instance loadb command do not cares :-) - * So advice is - do not relay on this... - */ -#define CONFIG_SYS_LOAD_ADDR 0x08400000 - -#define MHZ16QUARZINUSE - -#ifdef MHZ16QUARZINUSE -#define CONFIG_SYSPLL_CLK_FREQ 16000000 -#else -#define CONFIG_SYSPLL_CLK_FREQ 16780000 -#endif - -#define CONFIG_SYS_CLK_FREQ 16780000 - -/* FMCR Bit 0 becomes 0 to make CS3 CS3 :P */ -#define CONFIG_SYS_FMCR_VAL 0x00000001 - -/* Bit[0:3] contain PERCLK1DIV for UART 1 - 0x000b00b ->b<- -> 192MHz/12=16MHz - 0x000b00b ->8<- -> 144MHz/09=16MHz - 0x000b00b ->3<- -> 64MHz/4=16MHz */ - -#ifdef BUS96 -#define CONFIG_SYS_PCDR_VAL 0x000b00b5 -#endif - -#ifdef BUS64 -#define CONFIG_SYS_PCDR_VAL 0x000b00b3 -#endif - -#ifdef BUS72 -#define CONFIG_SYS_PCDR_VAL 0x000b00b8 -#endif - -#endif /* __CONFIG_H */