On 02/03/2015 06:00 AM, Vijay Rai wrote:
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC. It is similar to T1040RDB board with the following differences : - Has DDR4 memory - PHY ports have different PHY addresses - RTC support - Both QE-TDM and DIU connector T1040D4RDB supports 0x66 serdes protocol with following interfaces - 2 RGMII's on DTSEC4, DTSEC5 - 1 SGMII on DTSEC3 T1042D4RDB is variant of T1040D4RDB which hosts T1042 SoC (Personality of T1040 without L2 switch) T1042D4RDB supports 0x86 serdes protocol with following interfaces - 2 RGMII's on DTSEC4, DTSEC5 - 3 SGMII on DTSEC1, DTSEC2 & DTSEC3Signed-off-by: Vijay Rai vijay.rai@freescale.com Signed-off-by: Priyanka Jain Priyanka.Jain@freescale.com
board/freescale/t104xrdb/MAINTAINERS | 8 ++++++ board/freescale/t104xrdb/ddr.c | 7 +++++ board/freescale/t104xrdb/ddr.h | 12 ++++++++ board/freescale/t104xrdb/eth.c | 20 +++++++++++-- board/freescale/t104xrdb/t1040d4_rcw.cfg | 7 +++++ board/freescale/t104xrdb/t1042d4_rcw.cfg | 7 +++++ configs/T1040D4RDB_NAND_defconfig | 5 ++++ configs/T1040D4RDB_SDCARD_defconfig | 5 ++++ configs/T1040D4RDB_SPIFLASH_defconfig | 5 ++++ configs/T1040D4RDB_defconfig | 4 +++ configs/T1042D4RDB_NAND_defconfig | 5 ++++ configs/T1042D4RDB_SDCARD_defconfig | 5 ++++ configs/T1042D4RDB_SPIFLASH_defconfig | 5 ++++ configs/T1042D4RDB_defconfig | 4 +++ include/configs/T104xRDB.h | 46 ++++++++++++++++++++++++------ 15 files changed, 134 insertions(+), 11 deletions(-) create mode 100644 board/freescale/t104xrdb/t1040d4_rcw.cfg create mode 100644 board/freescale/t104xrdb/t1042d4_rcw.cfg create mode 100644 configs/T1040D4RDB_NAND_defconfig create mode 100644 configs/T1040D4RDB_SDCARD_defconfig create mode 100644 configs/T1040D4RDB_SPIFLASH_defconfig create mode 100644 configs/T1040D4RDB_defconfig create mode 100644 configs/T1042D4RDB_NAND_defconfig create mode 100644 configs/T1042D4RDB_SDCARD_defconfig create mode 100644 configs/T1042D4RDB_SPIFLASH_defconfig create mode 100644 configs/T1042D4RDB_defconfig
diff --git a/board/freescale/t104xrdb/MAINTAINERS b/board/freescale/t104xrdb/MAINTAINERS index 13d9be9..32e044f 100644 --- a/board/freescale/t104xrdb/MAINTAINERS +++ b/board/freescale/t104xrdb/MAINTAINERS @@ -6,7 +6,13 @@ F: include/configs/T104xRDB.h F: configs/T1040RDB_defconfig F: configs/T1040RDB_NAND_defconfig F: configs/T1040RDB_SPIFLASH_defconfig +F: configs/T1040D4RDB_defconfig +F: configs/T1040D4RDB_NAND_defconfig +F: configs/T1040D4RDB_SPIFLASH_defconfig F: configs/T1042RDB_defconfig +F: configs/T1042D4RDB_defconfig +F: configs/T1042D4RDB_NAND_defconfig +F: configs/T1042D4RDB_SPIFLASH_defconfig F: configs/T1042RDB_PI_defconfig F: configs/T1042RDB_PI_NAND_defconfig F: configs/T1042RDB_PI_SPIFLASH_defconfig @@ -15,6 +21,8 @@ T1040RDB_SDCARD BOARD #M: - S: Maintained F: configs/T1040RDB_SDCARD_defconfig +F: configs/T1040D4RDB_SDCARD_defconfig +F: configs/T1042D4RDB_SDCARD_defconfig F: configs/T1042RDB_PI_SDCARD_defconfig
T1040RDB_SECURE_BOOT BOARD diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c index e1148e5..217c8ea 100644 --- a/board/freescale/t104xrdb/ddr.c +++ b/board/freescale/t104xrdb/ddr.c @@ -91,9 +91,16 @@ found: popts->zq_en = 1;
/* DHC_EN =1, ODT = 75 Ohm */ +#ifdef CONFIG_SYS_FSL_DDR4
- popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
- popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */+#else popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +#endif } +#endif
#if defined(CONFIG_DEEP_SLEEP) void board_mem_sleep_setup(void)
You added extra #endif. Did you miss something? Please check your local code and make sure it compiles when sending patches.
York