On 03/29/2016 11:53 PM, Mario Six wrote:
To enable DM on MPC85xx, we need pre-relocation malloc, which is implemented in this patch.
Signed-off-by: Mario Six mario.six@gdsys.cc Cc: York Sun york.sun@nxp.com Cc: Simon Glass sjg@chromium.org
arch/powerpc/cpu/mpc85xx/cpu_init_early.c | 8 -------- arch/powerpc/cpu/mpc85xx/start.S | 28 ++++++++++++++++++++++++++++ 2 files changed, 28 insertions(+), 8 deletions(-)
diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init_early.c b/arch/powerpc/cpu/mpc85xx/cpu_init_early.c index 235a635..e6e1688 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init_early.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init_early.c @@ -82,7 +82,6 @@ void setup_ifc(void) void cpu_init_early_f(void *fdt) { u32 mas0, mas1, mas2, mas3, mas7;
- int i;
#ifdef CONFIG_SYS_FSL_ERRATUM_P1010_A003549 ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); #endif @@ -95,13 +94,6 @@ void cpu_init_early_f(void *fdt) /* Pointer is writable since we allocated a register for it */ gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
- /*
* Clear initial global data* we don't use memset so we can share this code with NAND_SPL*/- for (i = 0; i < sizeof(gd_t); i++)
((char *)gd)[i] = 0;#ifdef CONFIG_QEMU_E500 /* * CONFIG_SYS_CCSRBAR_PHYS below may use gd->fdt_blob on ePAPR systems, diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S index d867e2a..e6b5203 100644 --- a/arch/powerpc/cpu/mpc85xx/start.S +++ b/arch/powerpc/cpu/mpc85xx/start.S @@ -1152,6 +1152,34 @@ _start_cont: /* Setup the stack in initial RAM,could be L2-as-SRAM or L1 dcache*/ lis r3,(CONFIG_SYS_INIT_RAM_ADDR)@h ori r3,r3,((CONFIG_SYS_INIT_SP_OFFSET-16)&~0xf)@l /* Align to 16 */
+#ifdef CONFIG_SYS_MALLOC_F_LEN
- /* Leave 16+ byte for back chain termination and NULL return address */
- subi r3,r3,((CONFIG_SYS_MALLOC_F_LEN+16+15)&~0xf)
- /* End of RAM */
- lis r4,(CONFIG_SYS_INIT_RAM_ADDR)@h
- ori r4,r4,(CONFIG_SYS_INIT_RAM_SIZE)@l
- li r0,0
+1: subi r4,r4,4
- stw r0,0(r4)
- cmplw r4,r3
- bne 1b
- lis r4,(CONFIG_SYS_INIT_RAM_ADDR)@h
- ori r4,r4,(CONFIG_SYS_GBL_DATA_OFFSET)@l
- addi r3,r3,16 /* Pre-relocation malloc area */
- stw r3,GD_MALLOC_BASE(r4)
- subi r3,r3,16
- /* Fix issue with exception handler alignment */
- nop
- nop
- nop
Why do you need this? Does the code get too long and enters exception handler space?
+#endif li r0,0 stw r0,0(r3) /* Terminate Back Chain */ stw r0,+4(r3) /* NULL return address. */ --
This patch presumes stack is right under GD, which is OK. But CONFIG_SYS_MALLOC_F_LEN has not been used by powerpc. Presumption of (CONFIG_SYS_MALLOC_F_LEN + GENERATED_GBL_DATA_SIZE) < CONFIG_SYS_INIT_RAM_SIZE may not be true. Would it be better to check at compiling time to make sure we have enough init ram for the malloc len?
York