Use a similar pattern and delay values as the linux mainline driver to speed up failing when nothing is connected.
Reduce fail speed from around 5+ seconds down to around one second on a Radxa ROCK 3 Model A, where pcie2x1 is probed before pcie3x2 M2 slot.
Signed-off-by: Jonas Karlman jonas@kwiboo.se --- v2: - No change
drivers/pci/pcie_dw_rockchip.c | 68 ++++++++++++++++++---------------- 1 file changed, 37 insertions(+), 31 deletions(-)
diff --git a/drivers/pci/pcie_dw_rockchip.c b/drivers/pci/pcie_dw_rockchip.c index 1b8a1409f6df..82a8b9c96e2b 100644 --- a/drivers/pci/pcie_dw_rockchip.c +++ b/drivers/pci/pcie_dw_rockchip.c @@ -61,9 +61,6 @@ struct rk_pcie { #define PCIE_CLIENT_DBG_TRANSITION_DATA 0xffff0000 #define PCIE_CLIENT_DBF_EN 0xffff0003
-/* Parameters for the waiting for #perst signal */ -#define MACRO_US 1000 - static int rk_pcie_read(void __iomem *addr, int size, u32 *val) { if ((uintptr_t)addr & (size - 1)) { @@ -242,43 +239,46 @@ static int rk_pcie_link_up(struct rk_pcie *priv, u32 cap_speed) /* DW pre link configurations */ rk_pcie_configure(priv, cap_speed);
- /* Rest the device */ - if (dm_gpio_is_valid(&priv->rst_gpio)) { - dm_gpio_set_value(&priv->rst_gpio, 0); - /* - * Minimal is 100ms from spec but we see - * some wired devices need much more, such as 600ms. - * Add a enough delay to cover all cases. - */ - udelay(MACRO_US * 1000); - dm_gpio_set_value(&priv->rst_gpio, 1); - } - rk_pcie_disable_ltssm(priv); rk_pcie_link_status_clear(priv); rk_pcie_enable_debug(priv);
+ /* Reset the device */ + if (dm_gpio_is_valid(&priv->rst_gpio)) + dm_gpio_set_value(&priv->rst_gpio, 0); + /* Enable LTSSM */ rk_pcie_enable_ltssm(priv);
- for (retries = 0; retries < 5; retries++) { - if (is_link_up(priv)) { - dev_info(priv->dw.dev, "PCIe Link up, LTSSM is 0x%x\n", - rk_pcie_readl_apb(priv, PCIE_CLIENT_LTSSM_STATUS)); - rk_pcie_debug_dump(priv); - return 0; - } - - dev_info(priv->dw.dev, "PCIe Linking... LTSSM is 0x%x\n", - rk_pcie_readl_apb(priv, PCIE_CLIENT_LTSSM_STATUS)); - rk_pcie_debug_dump(priv); - udelay(MACRO_US * 1000); + /* + * PCIe requires the refclk to be stable for 100ms prior to releasing + * PERST. See table 2-4 in section 2.6.2 AC Specifications of the PCI + * Express Card Electromechanical Specification, 1.1. However, we don't + * know if the refclk is coming from RC's PHY or external OSC. If it's + * from RC, so enabling LTSSM is the just right place to release #PERST. + */ + mdelay(100); + if (dm_gpio_is_valid(&priv->rst_gpio)) + dm_gpio_set_value(&priv->rst_gpio, 1); + + /* Check if the link is up or not */ + for (retries = 0; retries < 10; retries++) { + if (is_link_up(priv)) + break; + + mdelay(100); + } + + if (retries >= 10) { + dev_err(priv->dw.dev, "PCIe-%d Link Fail\n", + dev_seq(priv->dw.dev)); + return -EIO; }
- dev_err(priv->dw.dev, "PCIe-%d Link Fail\n", dev_seq(priv->dw.dev)); - /* Link maybe in Gen switch recovery but we need to wait more 1s */ - udelay(MACRO_US * 1000); - return -EIO; + dev_info(priv->dw.dev, "PCIe Link up, LTSSM is 0x%x\n", + rk_pcie_readl_apb(priv, PCIE_CLIENT_LTSSM_STATUS)); + rk_pcie_debug_dump(priv); + return 0; }
static int rockchip_pcie_init_port(struct udevice *dev) @@ -287,6 +287,12 @@ static int rockchip_pcie_init_port(struct udevice *dev) u32 val; struct rk_pcie *priv = dev_get_priv(dev);
+ ret = reset_assert_bulk(&priv->rsts); + if (ret) { + dev_err(dev, "failed to assert resets (ret=%d)\n", ret); + return ret; + } + /* Set power and maybe external ref clk input */ ret = regulator_set_enable_if_allowed(priv->vpcie3v3, true); if (ret && ret != -ENOSYS) {