[U-Boot] [PATCH 07/14] net: gem: Extract phy init code

Move phy init code out of zynq_gem_init. DM drivers are normally calling this code from probe function.

Signed-off-by: Michal Simek michal.simek@xilinx.com ---

drivers/net/zynq_gem.c | 47 ++++++++++++++++++++++++++++++----------------- 1 file changed, 30 insertions(+), 17 deletions(-)

diff --git a/drivers/net/zynq_gem.c b/drivers/net/zynq_gem.c index 8f3fe9130066..86bb75905071 100644 --- a/drivers/net/zynq_gem.c +++ b/drivers/net/zynq_gem.c @@ -310,15 +310,10 @@ static int zynq_gem_setup_mac(struct eth_device *dev) return 0; }

-static int zynq_gem_init(struct eth_device *dev, bd_t * bis) +static int zynq_phy_init(struct eth_device *dev) { - u32 i; int ret; - unsigned long clk_rate = 0; - struct zynq_gem_regs *regs = (struct zynq_gem_regs *)dev->iobase; struct zynq_gem_priv *priv = dev->priv; - struct emac_bd *dummy_tx_bd = &priv->tx_bd[TX_FREE_DESC]; - struct emac_bd *dummy_rx_bd = &priv->tx_bd[TX_FREE_DESC + 2]; const u32 supported = SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Half | @@ -326,6 +321,33 @@ static int zynq_gem_init(struct eth_device *dev, bd_t * bis) SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full;

+ ret = phy_detection(dev); + if (ret) { + printf("GEM PHY init failed\n"); + return ret; + } + + priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev, + priv->interface); + + priv->phydev->supported = supported | ADVERTISED_Pause | + ADVERTISED_Asym_Pause; + priv->phydev->advertising = priv->phydev->supported; + phy_config(priv->phydev); + + return 0; +} + +static int zynq_gem_init(struct eth_device *dev, bd_t *bis) +{ + u32 i; + int ret; + unsigned long clk_rate = 0; + struct zynq_gem_regs *regs = (struct zynq_gem_regs *)dev->iobase; + struct zynq_gem_priv *priv = dev->priv; + struct emac_bd *dummy_tx_bd = &priv->tx_bd[TX_FREE_DESC]; + struct emac_bd *dummy_rx_bd = &priv->tx_bd[TX_FREE_DESC + 2]; + if (!priv->init) { /* Disable all interrupts */ writel(0xFFFFFFFF, &regs->idr); @@ -387,19 +409,10 @@ static int zynq_gem_init(struct eth_device *dev, bd_t * bis) priv->init++; }

- ret = phy_detection(dev); - if (ret) { - printf("GEM PHY init failed\n"); + ret = zynq_phy_init(dev); + if (ret) return ret; - } - - priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev, - priv->interface);

- priv->phydev->supported = supported | ADVERTISED_Pause | - ADVERTISED_Asym_Pause; - priv->phydev->advertising = priv->phydev->supported; - phy_config(priv->phydev); phy_startup(priv->phydev);

if (!priv->phydev->link) {