From: Mugunthan V N mugunthanvnm@ti.com
spi bus can support dual and quad wire data transfers for tx and rx. So defining dual and quad modes for both tx and rx. Also add support to parse bus width used for spi tx and rx transfers.
Signed-off-by: Mugunthan V N mugunthanvnm@ti.com Reviewed-by: Jagan Teki jteki@openedev.com --- Changes for v7: - Fixed SPI_TX_DUAL - Removed mode_tx from spi_slave{}
drivers/spi/spi-uclass.c | 38 +++++++++++++++++++++++++++++++++++++- include/spi.h | 2 ++ 2 files changed, 39 insertions(+), 1 deletion(-)
diff --git a/drivers/spi/spi-uclass.c b/drivers/spi/spi-uclass.c index e0f6b25..f1ff5f4 100644 --- a/drivers/spi/spi-uclass.c +++ b/drivers/spi/spi-uclass.c @@ -157,6 +157,7 @@ static int spi_child_pre_probe(struct udevice *dev)
slave->max_hz = plat->max_hz; slave->mode = plat->mode; + slave->mode_rx = plat->mode_rx;
return 0; } @@ -368,7 +369,8 @@ void spi_free_slave(struct spi_slave *slave) int spi_slave_ofdata_to_platdata(const void *blob, int node, struct dm_spi_slave_platdata *plat) { - int mode = 0; + int mode = 0, mode_rx = 0; + int value;
plat->cs = fdtdec_get_int(blob, node, "reg", -1); plat->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency", 0); @@ -382,8 +384,42 @@ int spi_slave_ofdata_to_platdata(const void *blob, int node, mode |= SPI_3WIRE; if (fdtdec_get_bool(blob, node, "spi-half-duplex")) mode |= SPI_PREAMBLE; + + /* Device DUAL/QUAD mode */ + value = fdtdec_get_uint(blob, node, "spi-tx-bus-width", 1); + switch (value) { + case 1: + break; + case 2: + mode |= SPI_TX_DUAL; + break; + case 4: + mode |= SPI_TX_QUAD; + break; + default: + error("spi-tx-bus-width %d not supported\n", value); + break; + } + plat->mode = mode;
+ value = fdtdec_get_uint(blob, node, "spi-rx-bus-width", 1); + switch (value) { + case 1: + break; + case 2: + plat->mode_rx |= SPI_RX_DUAL; + break; + case 4: + plat->mode_rx |= SPI_RX_QUAD; + break; + default: + error("spi-rx-bus-width %d not supported\n", value); + break; + } + + plat->mode_rx = mode_rx; + return 0; }
diff --git a/include/spi.h b/include/spi.h index 25470e4..4b88d39 100644 --- a/include/spi.h +++ b/include/spi.h @@ -61,11 +61,13 @@ struct dm_spi_bus { * @cs: Chip select number (0..n-1) * @max_hz: Maximum bus speed that this slave can tolerate * @mode: SPI mode to use for this device (see SPI mode flags) + * @mode_rx: SPI RX mode to use for this slave (see SPI mode_rx flags) */ struct dm_spi_slave_platdata { unsigned int cs; uint max_hz; uint mode; + u8 mode_rx; };
#endif /* CONFIG_DM_SPI */