On 18 March 2015 at 14:34, Albert ARIBAUD (3ADEV) albert.aribaud@3adev.fr wrote:
Signed-off-by: Albert ARIBAUD (3ADEV) albert.aribaud@3adev.fr
Changes in v6: None Changes in v5: None Changes in v4: None Changes in v3:
- move regs and functions in private struct
Changes in v2:
- added MUX setting for SSP0
arch/arm/cpu/arm926ejs/lpc32xx/devices.c | 14 +++ arch/arm/include/asm/arch-lpc32xx/clk.h | 3 + arch/arm/include/asm/arch-lpc32xx/sys_proto.h | 1 + drivers/spi/Makefile | 1 + drivers/spi/lpc32xx_ssp.c | 144 ++++++++++++++++++++++++++ 5 files changed, 163 insertions(+) create mode 100644 drivers/spi/lpc32xx_ssp.c
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c index a407098..5a453e3 100644 --- a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c +++ b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c @@ -8,11 +8,13 @@ #include <asm/arch/cpu.h> #include <asm/arch/clk.h> #include <asm/arch/uart.h> +#include <asm/arch/mux.h> #include <asm/io.h> #include <dm.h>
static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE; static struct uart_ctrl_regs *ctrl = (struct uart_ctrl_regs *)UART_CTRL_BASE; +static struct mux_regs *mux = (struct mux_regs *)MUX_BASE;
void lpc32xx_uart_init(unsigned int uart_id) { @@ -66,3 +68,15 @@ void lpc32xx_i2c_init(unsigned int devnum) U_BOOT_DEVICE(lpc32xx_gpios) = { .name = "gpio_lpc32xx" };
+/* Mux for SCK0, MISO0, MOSI0. We do not use SSEL0. */
+#define P_MUX_SET_SSP0 0x1600
+void lpc32xx_ssp_init(void) +{
/* Enable SSP0 interface */writel(CLK_SSP0_ENABLE_CLOCK, &clk->ssp_ctrl);/* Mux SSP0 pins */writel(P_MUX_SET_SSP0, &mux->p_mux_set);+} diff --git a/arch/arm/include/asm/arch-lpc32xx/clk.h b/arch/arm/include/asm/arch-lpc32xx/clk.h index 781ac07..2cb5703 100644 --- a/arch/arm/include/asm/arch-lpc32xx/clk.h +++ b/arch/arm/include/asm/arch-lpc32xx/clk.h @@ -155,6 +155,9 @@ struct clk_pm_regs { #define CLK_NAND_MLC (1 << 1) #define CLK_NAND_MLC_INT (1 << 5)
+/* SSP Clock Control Register bits */ +#define CLK_SSP0_ENABLE_CLOCK (1 << 0)
unsigned int get_sys_clk_rate(void); unsigned int get_hclk_pll_rate(void); unsigned int get_hclk_clk_div(void); diff --git a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h index a4a05d1..86d5ee9 100644 --- a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h +++ b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h @@ -11,5 +11,6 @@ void lpc32xx_uart_init(unsigned int uart_id); void lpc32xx_mac_init(void); void lpc32xx_mlc_nand_init(void); void lpc32xx_i2c_init(unsigned int devnum); +void lpc32xx_ssp_init(void);
#endif /* _LPC32XX_SYS_PROTO_H */ diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index edbd520..ce6f1cc 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -32,6 +32,7 @@ obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o obj-$(CONFIG_FTSSP010_SPI) += ftssp010_spi.o obj-$(CONFIG_ICH_SPI) += ich.o obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o +obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o obj-$(CONFIG_MPC52XX_SPI) += mpc52xx_spi.o obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o obj-$(CONFIG_MXC_SPI) += mxc_spi.o diff --git a/drivers/spi/lpc32xx_ssp.c b/drivers/spi/lpc32xx_ssp.c new file mode 100644 index 0000000..0fc44a0 --- /dev/null +++ b/drivers/spi/lpc32xx_ssp.c @@ -0,0 +1,144 @@ +/*
- LPC32xx SSP interface (SPI mode)
- (C) Copyright 2014 DENX Software Engineering GmbH
- Written-by: Albert ARIBAUD albert.aribaud@3adev.fr
- SPDX-License-Identifier: GPL-2.0+
- */
+#include <common.h> +#include <linux/compat.h> +#include <asm/io.h> +#include <malloc.h> +#include <spi.h> +#include <asm/arch/clk.h>
+/* SSP chip registers */ +struct ssp_regs {
u32 cr0;u32 cr1;u32 data;u32 sr;u32 cpsr;u32 imsc;u32 ris;u32 mis;u32 icr;u32 dmacr;+};
+/* CR1 register defines */ +#define SSP_CR1_SSP_ENABLE 0x0002
+/* SR register defines */ +#define SSP_SR_TNF 0x0002 +/* SSP status RX FIFO not empty bit */ +#define SSP_SR_RNE 0x0004
+/* zynq spi slave */
Typo here.. zynq
+struct lpc32xx_spi_slave {
struct spi_slave slave;struct ssp_regs *regs;+};
+static inline struct lpc32xx_spi_slave *to_lpc32xx_spi_slave(
struct spi_slave *slave)+{
return container_of(slave, struct lpc32xx_spi_slave, slave);+}
+/* spi_init is called during boot when CONFIG_CMD_SPI is defined */ +void spi_init(void) +{
/** nothing to do: clocking was enabled in lpc32xx_ssp_enable()* and configuration will be done in spi_setup_slave()*/+}
+/* the following is called in sequence by do_spi_xfer() */
+struct spi_slave *spi_setup_slave(uint bus, uint cs, uint max_hz, uint mode) +{
struct lpc32xx_spi_slave *lslave;/* we only set up SSP0 for now, so ignore bus */if (mode & SPI_3WIRE) {error("3-wire mode not supported");return NULL;}if (mode & SPI_SLAVE) {error("slave mode not supported\n");return NULL;}if (mode & SPI_PREAMBLE) {error("preamble byte skipping not supported\n");return NULL;}lslave = spi_alloc_slave(struct lpc32xx_spi_slave, bus, cs);if (!lslave) {printf("SPI_error: Fail to allocate lpc32xx_spi_slave\n");return NULL;}lslave->regs = (struct ssp_regs *)SSP0_BASE;/** 8 bit frame, SPI fmt, 500kbps -> clock divider is 26.* Set SCR to 0 and CPSDVSR to 26.*/writel(0x7, &lslave->regs->cr0); /* 8-bit chunks, SPI, 1 clk/bit */writel(26, &lslave->regs->cpsr); /* SSP clock = HCLK/26 = 500kbps */writel(0, &lslave->regs->imsc); /* do not raise any interrupts */writel(0, &lslave->regs->icr); /* clear any pending interrupt */writel(0, &lslave->regs->dmacr); /* do not do DMAs */writel(SSP_CR1_SSP_ENABLE, &lslave->regs->cr1); /* enable SSP0 */return &lslave->slave;+}
+void spi_free_slave(struct spi_slave *slave) +{
struct lpc32xx_spi_slave *lslave = to_lpc32xx_spi_slave(slave);debug("(lpc32xx) spi_free_slave: 0x%08x\n", (u32)lslave);free(lslave);+}
+int spi_claim_bus(struct spi_slave *slave) +{
/* only one bus and slave so far, always available */return 0;+}
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
const void *dout, void *din, unsigned long flags)+{
struct lpc32xx_spi_slave *lslave = to_lpc32xx_spi_slave(slave);int bytelen = bitlen >> 3;int idx_out = 0;int idx_in = 0;int start_time;start_time = get_timer(0);while ((idx_out < bytelen) || (idx_in < bytelen)) {int status = readl(&lslave->regs->sr);if ((idx_out < bytelen) && (status & SSP_SR_TNF))writel(((u8 *)dout)[idx_out++], &lslave->regs->data);if ((idx_in < bytelen) && (status & status & SSP_SR_RNE))((u8 *)din)[idx_in++] = readl(&lslave->regs->data);if (get_timer(start_time) >= CONFIG_LPC32XX_SSP_TIMEOUT)return -1;}return 0;+}
+void spi_release_bus(struct spi_slave *slave) +{
/* do nothing */+}
2.1.0
Reviewed-by: Jagannadha Sutradharudu Teki jagannadh.teki@gmail.com
thanks!