On 2020/5/13 下午3:15, Frank Wang wrote:
From: Jagan Teki jagan@amarulasolutions.com
Add USB TYPEC PHY driver for rockchip platform.
Referenced from Linux TypeC PHY driver, currently supporting usb3-port and dp-port need to add it in the future.
Signed-off-by: Frank Wang frank.wang@rock-chips.com Signed-off-by: Jagan Teki jagan@amarulasolutions.com
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, - Kever
drivers/phy/rockchip/Kconfig | 7 + drivers/phy/rockchip/Makefile | 1 + drivers/phy/rockchip/phy-rockchip-typec.c | 796 ++++++++++++++++++++++ 3 files changed, 804 insertions(+) create mode 100644 drivers/phy/rockchip/phy-rockchip-typec.c
diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig index d73ac695e1..84cc7c876d 100644 --- a/drivers/phy/rockchip/Kconfig +++ b/drivers/phy/rockchip/Kconfig @@ -11,4 +11,11 @@ config PHY_ROCKCHIP_INNO_USB2 help Support for Rockchip USB2.0 PHY with Innosilicon IP block.
+config PHY_ROCKCHIP_TYPEC
- bool "Rockchip TYPEC PHY Driver"
- depends on ARCH_ROCKCHIP
- select PHY
- help
Enable this to support the Rockchip USB TYPEC PHY.- endmenu
diff --git a/drivers/phy/rockchip/Makefile b/drivers/phy/rockchip/Makefile index 9b0cbc6acf..95b2f8a3c0 100644 --- a/drivers/phy/rockchip/Makefile +++ b/drivers/phy/rockchip/Makefile @@ -4,3 +4,4 @@ #
obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o +obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c new file mode 100644 index 0000000000..c9c8e1c542 --- /dev/null +++ b/drivers/phy/rockchip/phy-rockchip-typec.c @@ -0,0 +1,796 @@ +// SPDX-License-Identifier: GPL-2.0-only +/*
- ROCKCHIP Type-C PHY driver.
- Copyright (C) 2020 Amarula Solutions(India)
- Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
- Author: Chris Zhong zyw@rock-chips.com
Kever Yang <kever.yang@rock-chips.com>- */
+#include <common.h> +#include <clk.h> +#include <dm.h> +#include <dm/device_compat.h> +#include <dm/lists.h> +#include <generic-phy.h> +#include <reset.h> +#include <syscon.h> +#include <asm/gpio.h> +#include <asm/io.h> +#include <linux/iopoll.h> +#include <asm/arch-rockchip/clock.h>
+DECLARE_GLOBAL_DATA_PTR;
+#define usleep_range(a, b) udelay((b))
+#define CMN_SSM_BANDGAP (0x21 << 2) +#define CMN_SSM_BIAS (0x22 << 2) +#define CMN_PLLSM0_PLLEN (0x29 << 2) +#define CMN_PLLSM0_PLLPRE (0x2a << 2) +#define CMN_PLLSM0_PLLVREF (0x2b << 2) +#define CMN_PLLSM0_PLLLOCK (0x2c << 2) +#define CMN_PLLSM1_PLLEN (0x31 << 2) +#define CMN_PLLSM1_PLLPRE (0x32 << 2) +#define CMN_PLLSM1_PLLVREF (0x33 << 2) +#define CMN_PLLSM1_PLLLOCK (0x34 << 2) +#define CMN_PLLSM1_USER_DEF_CTRL (0x37 << 2) +#define CMN_ICAL_OVRD (0xc1 << 2) +#define CMN_PLL0_VCOCAL_OVRD (0x83 << 2) +#define CMN_PLL0_VCOCAL_INIT (0x84 << 2) +#define CMN_PLL0_VCOCAL_ITER (0x85 << 2) +#define CMN_PLL0_LOCK_REFCNT_START (0x90 << 2) +#define CMN_PLL0_LOCK_PLLCNT_START (0x92 << 2) +#define CMN_PLL0_LOCK_PLLCNT_THR (0x93 << 2) +#define CMN_PLL0_INTDIV (0x94 << 2) +#define CMN_PLL0_FRACDIV (0x95 << 2) +#define CMN_PLL0_HIGH_THR (0x96 << 2) +#define CMN_PLL0_DSM_DIAG (0x97 << 2) +#define CMN_PLL0_SS_CTRL1 (0x98 << 2) +#define CMN_PLL0_SS_CTRL2 (0x99 << 2) +#define CMN_PLL1_VCOCAL_START (0xa1 << 2) +#define CMN_PLL1_VCOCAL_OVRD (0xa3 << 2) +#define CMN_PLL1_VCOCAL_INIT (0xa4 << 2) +#define CMN_PLL1_VCOCAL_ITER (0xa5 << 2) +#define CMN_PLL1_LOCK_REFCNT_START (0xb0 << 2) +#define CMN_PLL1_LOCK_PLLCNT_START (0xb2 << 2) +#define CMN_PLL1_LOCK_PLLCNT_THR (0xb3 << 2) +#define CMN_PLL1_INTDIV (0xb4 << 2) +#define CMN_PLL1_FRACDIV (0xb5 << 2) +#define CMN_PLL1_HIGH_THR (0xb6 << 2) +#define CMN_PLL1_DSM_DIAG (0xb7 << 2) +#define CMN_PLL1_SS_CTRL1 (0xb8 << 2) +#define CMN_PLL1_SS_CTRL2 (0xb9 << 2) +#define CMN_RXCAL_OVRD (0xd1 << 2)
+#define CMN_TXPUCAL_CTRL (0xe0 << 2) +#define CMN_TXPUCAL_OVRD (0xe1 << 2) +#define CMN_TXPDCAL_CTRL (0xf0 << 2) +#define CMN_TXPDCAL_OVRD (0xf1 << 2)
+/* For CMN_TXPUCAL_CTRL, CMN_TXPDCAL_CTRL */ +#define CMN_TXPXCAL_START BIT(15) +#define CMN_TXPXCAL_DONE BIT(14) +#define CMN_TXPXCAL_NO_RESPONSE BIT(13) +#define CMN_TXPXCAL_CURRENT_RESPONSE BIT(12)
+#define CMN_TXPU_ADJ_CTRL (0x108 << 2) +#define CMN_TXPD_ADJ_CTRL (0x10c << 2)
+/*
- For CMN_TXPUCAL_CTRL, CMN_TXPDCAL_CTRL,
CMN_TXPU_ADJ_CTRL, CMN_TXPDCAL_CTRL
- NOTE: some of these registers are documented to be 2's complement
- signed numbers, but then documented to be always positive. Weird.
- In such a case, using CMN_CALIB_CODE_POS() avoids the unnecessary
- sign extension.
- */
+#define CMN_CALIB_CODE_WIDTH 7 +#define CMN_CALIB_CODE_OFFSET 0 +#define CMN_CALIB_CODE_MASK GENMASK(CMN_CALIB_CODE_WIDTH, 0) +#define CMN_CALIB_CODE(x) \
- sign_extend32((x) >> CMN_CALIB_CODE_OFFSET, CMN_CALIB_CODE_WIDTH)
+#define CMN_CALIB_CODE_POS_MASK GENMASK(CMN_CALIB_CODE_WIDTH - 1, 0) +#define CMN_CALIB_CODE_POS(x) \
- (((x) >> CMN_CALIB_CODE_OFFSET) & CMN_CALIB_CODE_POS_MASK)
+#define CMN_DIAG_PLL0_FBH_OVRD (0x1c0 << 2) +#define CMN_DIAG_PLL0_FBL_OVRD (0x1c1 << 2) +#define CMN_DIAG_PLL0_OVRD (0x1c2 << 2) +#define CMN_DIAG_PLL0_V2I_TUNE (0x1c5 << 2) +#define CMN_DIAG_PLL0_CP_TUNE (0x1c6 << 2) +#define CMN_DIAG_PLL0_LF_PROG (0x1c7 << 2) +#define CMN_DIAG_PLL1_FBH_OVRD (0x1d0 << 2) +#define CMN_DIAG_PLL1_FBL_OVRD (0x1d1 << 2) +#define CMN_DIAG_PLL1_OVRD (0x1d2 << 2) +#define CMN_DIAG_PLL1_V2I_TUNE (0x1d5 << 2) +#define CMN_DIAG_PLL1_CP_TUNE (0x1d6 << 2) +#define CMN_DIAG_PLL1_LF_PROG (0x1d7 << 2) +#define CMN_DIAG_PLL1_PTATIS_TUNE1 (0x1d8 << 2) +#define CMN_DIAG_PLL1_PTATIS_TUNE2 (0x1d9 << 2) +#define CMN_DIAG_PLL1_INCLK_CTRL (0x1da << 2) +#define CMN_DIAG_HSCLK_SEL (0x1e0 << 2)
+#define XCVR_PSM_RCTRL(n) ((0x4001 | ((n) << 9)) << 2) +#define XCVR_PSM_CAL_TMR(n) ((0x4002 | ((n) << 9)) << 2) +#define XCVR_PSM_A0IN_TMR(n) ((0x4003 | ((n) << 9)) << 2) +#define TX_TXCC_CAL_SCLR_MULT(n) ((0x4047 | ((n) << 9)) << 2) +#define TX_TXCC_CPOST_MULT_00(n) ((0x404c | ((n) << 9)) << 2) +#define TX_TXCC_CPOST_MULT_01(n) ((0x404d | ((n) << 9)) << 2) +#define TX_TXCC_CPOST_MULT_10(n) ((0x404e | ((n) << 9)) << 2) +#define TX_TXCC_CPOST_MULT_11(n) ((0x404f | ((n) << 9)) << 2) +#define TX_TXCC_MGNFS_MULT_000(n) ((0x4050 | ((n) << 9)) << 2) +#define TX_TXCC_MGNFS_MULT_001(n) ((0x4051 | ((n) << 9)) << 2) +#define TX_TXCC_MGNFS_MULT_010(n) ((0x4052 | ((n) << 9)) << 2) +#define TX_TXCC_MGNFS_MULT_011(n) ((0x4053 | ((n) << 9)) << 2) +#define TX_TXCC_MGNFS_MULT_100(n) ((0x4054 | ((n) << 9)) << 2) +#define TX_TXCC_MGNFS_MULT_101(n) ((0x4055 | ((n) << 9)) << 2) +#define TX_TXCC_MGNFS_MULT_110(n) ((0x4056 | ((n) << 9)) << 2) +#define TX_TXCC_MGNFS_MULT_111(n) ((0x4057 | ((n) << 9)) << 2) +#define TX_TXCC_MGNLS_MULT_000(n) ((0x4058 | ((n) << 9)) << 2) +#define TX_TXCC_MGNLS_MULT_001(n) ((0x4059 | ((n) << 9)) << 2) +#define TX_TXCC_MGNLS_MULT_010(n) ((0x405a | ((n) << 9)) << 2) +#define TX_TXCC_MGNLS_MULT_011(n) ((0x405b | ((n) << 9)) << 2) +#define TX_TXCC_MGNLS_MULT_100(n) ((0x405c | ((n) << 9)) << 2) +#define TX_TXCC_MGNLS_MULT_101(n) ((0x405d | ((n) << 9)) << 2) +#define TX_TXCC_MGNLS_MULT_110(n) ((0x405e | ((n) << 9)) << 2) +#define TX_TXCC_MGNLS_MULT_111(n) ((0x405f | ((n) << 9)) << 2)
+#define XCVR_DIAG_PLLDRC_CTRL(n) ((0x40e0 | ((n) << 9)) << 2) +#define XCVR_DIAG_BIDI_CTRL(n) ((0x40e8 | ((n) << 9)) << 2) +#define XCVR_DIAG_LANE_FCM_EN_MGN(n) ((0x40f2 | ((n) << 9)) << 2) +#define TX_PSC_A0(n) ((0x4100 | ((n) << 9)) << 2) +#define TX_PSC_A1(n) ((0x4101 | ((n) << 9)) << 2) +#define TX_PSC_A2(n) ((0x4102 | ((n) << 9)) << 2) +#define TX_PSC_A3(n) ((0x4103 | ((n) << 9)) << 2) +#define TX_RCVDET_CTRL(n) ((0x4120 | ((n) << 9)) << 2) +#define TX_RCVDET_EN_TMR(n) ((0x4122 | ((n) << 9)) << 2) +#define TX_RCVDET_ST_TMR(n) ((0x4123 | ((n) << 9)) << 2) +#define TX_DIAG_TX_DRV(n) ((0x41e1 | ((n) << 9)) << 2) +#define TX_DIAG_BGREF_PREDRV_DELAY (0x41e7 << 2)
+/* Use this for "n" in macros like "_MULT_XXX" to target the aux channel */ +#define AUX_CH_LANE 8
+#define TX_ANA_CTRL_REG_1 (0x5020 << 2)
+#define TXDA_DP_AUX_EN BIT(15) +#define AUXDA_SE_EN BIT(14) +#define TXDA_CAL_LATCH_EN BIT(13) +#define AUXDA_POLARITY BIT(12) +#define TXDA_DRV_POWER_ISOLATION_EN BIT(11) +#define TXDA_DRV_POWER_EN_PH_2_N BIT(10) +#define TXDA_DRV_POWER_EN_PH_1_N BIT(9) +#define TXDA_BGREF_EN BIT(8) +#define TXDA_DRV_LDO_EN BIT(7) +#define TXDA_DECAP_EN_DEL BIT(6) +#define TXDA_DECAP_EN BIT(5) +#define TXDA_UPHY_SUPPLY_EN_DEL BIT(4) +#define TXDA_UPHY_SUPPLY_EN BIT(3) +#define TXDA_LOW_LEAKAGE_EN BIT(2) +#define TXDA_DRV_IDLE_LOWI_EN BIT(1) +#define TXDA_DRV_CMN_MODE_EN BIT(0)
+#define TX_ANA_CTRL_REG_2 (0x5021 << 2)
+#define AUXDA_DEBOUNCING_CLK BIT(15) +#define TXDA_LPBK_RECOVERED_CLK_EN BIT(14) +#define TXDA_LPBK_ISI_GEN_EN BIT(13) +#define TXDA_LPBK_SERIAL_EN BIT(12) +#define TXDA_LPBK_LINE_EN BIT(11) +#define TXDA_DRV_LDO_REDC_SINKIQ BIT(10) +#define XCVR_DECAP_EN_DEL BIT(9) +#define XCVR_DECAP_EN BIT(8) +#define TXDA_MPHY_ENABLE_HS_NT BIT(7) +#define TXDA_MPHY_SA_MODE BIT(6) +#define TXDA_DRV_LDO_RBYR_FB_EN BIT(5) +#define TXDA_DRV_RST_PULL_DOWN BIT(4) +#define TXDA_DRV_LDO_BG_FB_EN BIT(3) +#define TXDA_DRV_LDO_BG_REF_EN BIT(2) +#define TXDA_DRV_PREDRV_EN_DEL BIT(1) +#define TXDA_DRV_PREDRV_EN BIT(0)
+#define TXDA_COEFF_CALC_CTRL (0x5022 << 2)
+#define TX_HIGH_Z BIT(6) +#define TX_VMARGIN_OFFSET 3 +#define TX_VMARGIN_MASK 0x7 +#define LOW_POWER_SWING_EN BIT(2) +#define TX_FCM_DRV_MAIN_EN BIT(1) +#define TX_FCM_FULL_MARGIN BIT(0)
+#define TX_DIG_CTRL_REG_2 (0x5024 << 2)
+#define TX_HIGH_Z_TM_EN BIT(15) +#define TX_RESCAL_CODE_OFFSET 0 +#define TX_RESCAL_CODE_MASK 0x3f
+#define TXDA_CYA_AUXDA_CYA (0x5025 << 2) +#define TX_ANA_CTRL_REG_3 (0x5026 << 2) +#define TX_ANA_CTRL_REG_4 (0x5027 << 2) +#define TX_ANA_CTRL_REG_5 (0x5029 << 2)
+#define RX_PSC_A0(n) ((0x8000 | ((n) << 9)) << 2) +#define RX_PSC_A1(n) ((0x8001 | ((n) << 9)) << 2) +#define RX_PSC_A2(n) ((0x8002 | ((n) << 9)) << 2) +#define RX_PSC_A3(n) ((0x8003 | ((n) << 9)) << 2) +#define RX_PSC_CAL(n) ((0x8006 | ((n) << 9)) << 2) +#define RX_PSC_RDY(n) ((0x8007 | ((n) << 9)) << 2) +#define RX_IQPI_ILL_CAL_OVRD (0x8023 << 2) +#define RX_EPI_ILL_CAL_OVRD (0x8033 << 2) +#define RX_SDCAL0_OVRD (0x8041 << 2) +#define RX_SDCAL1_OVRD (0x8049 << 2) +#define RX_SLC_INIT (0x806d << 2) +#define RX_SLC_RUN (0x806e << 2) +#define RX_CDRLF_CNFG2 (0x8081 << 2) +#define RX_SIGDET_HL_FILT_TMR(n) ((0x8090 | ((n) << 9)) << 2) +#define RX_SLC_IOP0_OVRD (0x8101 << 2) +#define RX_SLC_IOP1_OVRD (0x8105 << 2) +#define RX_SLC_QOP0_OVRD (0x8109 << 2) +#define RX_SLC_QOP1_OVRD (0x810d << 2) +#define RX_SLC_EOP0_OVRD (0x8111 << 2) +#define RX_SLC_EOP1_OVRD (0x8115 << 2) +#define RX_SLC_ION0_OVRD (0x8119 << 2) +#define RX_SLC_ION1_OVRD (0x811d << 2) +#define RX_SLC_QON0_OVRD (0x8121 << 2) +#define RX_SLC_QON1_OVRD (0x8125 << 2) +#define RX_SLC_EON0_OVRD (0x8129 << 2) +#define RX_SLC_EON1_OVRD (0x812d << 2) +#define RX_SLC_IEP0_OVRD (0x8131 << 2) +#define RX_SLC_IEP1_OVRD (0x8135 << 2) +#define RX_SLC_QEP0_OVRD (0x8139 << 2) +#define RX_SLC_QEP1_OVRD (0x813d << 2) +#define RX_SLC_EEP0_OVRD (0x8141 << 2) +#define RX_SLC_EEP1_OVRD (0x8145 << 2) +#define RX_SLC_IEN0_OVRD (0x8149 << 2) +#define RX_SLC_IEN1_OVRD (0x814d << 2) +#define RX_SLC_QEN0_OVRD (0x8151 << 2) +#define RX_SLC_QEN1_OVRD (0x8155 << 2) +#define RX_SLC_EEN0_OVRD (0x8159 << 2) +#define RX_SLC_EEN1_OVRD (0x815d << 2) +#define RX_REE_CTRL_DATA_MASK(n) ((0x81bb | ((n) << 9)) << 2) +#define RX_DIAG_SIGDET_TUNE(n) ((0x81dc | ((n) << 9)) << 2) +#define RX_DIAG_SC2C_DELAY (0x81e1 << 2)
+#define PMA_LANE_CFG (0xc000 << 2) +#define PIPE_CMN_CTRL1 (0xc001 << 2) +#define PIPE_CMN_CTRL2 (0xc002 << 2) +#define PIPE_COM_LOCK_CFG1 (0xc003 << 2) +#define PIPE_COM_LOCK_CFG2 (0xc004 << 2) +#define PIPE_RCV_DET_INH (0xc005 << 2) +#define DP_MODE_CTL (0xc008 << 2) +#define DP_CLK_CTL (0xc009 << 2) +#define STS (0xc00F << 2) +#define PHY_ISO_CMN_CTRL (0xc010 << 2) +#define PHY_DP_TX_CTL (0xc408 << 2) +#define PMA_CMN_CTRL1 (0xc800 << 2) +#define PHY_PMA_ISO_CMN_CTRL (0xc810 << 2) +#define PHY_ISOLATION_CTRL (0xc81f << 2) +#define PHY_PMA_ISO_XCVR_CTRL(n) ((0xcc11 | ((n) << 6)) << 2) +#define PHY_PMA_ISO_LINK_MODE(n) ((0xcc12 | ((n) << 6)) << 2) +#define PHY_PMA_ISO_PWRST_CTRL(n) ((0xcc13 | ((n) << 6)) << 2) +#define PHY_PMA_ISO_TX_DATA_LO(n) ((0xcc14 | ((n) << 6)) << 2) +#define PHY_PMA_ISO_TX_DATA_HI(n) ((0xcc15 | ((n) << 6)) << 2) +#define PHY_PMA_ISO_RX_DATA_LO(n) ((0xcc16 | ((n) << 6)) << 2) +#define PHY_PMA_ISO_RX_DATA_HI(n) ((0xcc17 | ((n) << 6)) << 2) +#define TX_BIST_CTRL(n) ((0x4140 | ((n) << 9)) << 2) +#define TX_BIST_UDDWR(n) ((0x4141 | ((n) << 9)) << 2)
+/*
- Selects which PLL clock will be driven on the analog high speed
- clock 0: PLL 0 div 1
- clock 1: PLL 1 div 2
- */
+#define CLK_PLL_CONFIG 0X30 +#define CLK_PLL_MASK 0x33
+#define CMN_READY BIT(0)
+#define DP_PLL_CLOCK_ENABLE BIT(2) +#define DP_PLL_ENABLE BIT(0) +#define DP_PLL_DATA_RATE_RBR ((2 << 12) | (4 << 8)) +#define DP_PLL_DATA_RATE_HBR ((2 << 12) | (4 << 8)) +#define DP_PLL_DATA_RATE_HBR2 ((1 << 12) | (2 << 8))
+#define DP_MODE_A0 BIT(4) +#define DP_MODE_A2 BIT(6) +#define DP_MODE_ENTER_A0 0xc101 +#define DP_MODE_ENTER_A2 0xc104
+#define PHY_MODE_SET_TIMEOUT 100000
+#define PIN_ASSIGN_C_E 0x51d9 +#define PIN_ASSIGN_D_F 0x5100
+#define MODE_DISCONNECT 0 +#define MODE_UFP_USB BIT(0) +#define MODE_DFP_USB BIT(1) +#define MODE_DFP_DP BIT(2)
+struct usb3phy_reg {
- u32 offset;
- u32 enable_bit;
- u32 write_enable;
+};
+/**
- struct rockchip_usb3phy_port_cfg: usb3-phy port configuration.
- @reg: the base address for usb3-phy config.
- @typec_conn_dir: the register of type-c connector direction.
- @usb3tousb2_en: the register of type-c force usb2 to usb2 enable.
- @external_psm: the register of type-c phy external psm clock.
- @pipe_status: the register of type-c phy pipe status.
- @usb3_host_disable: the register of type-c usb3 host disable.
- @usb3_host_port: the register of type-c usb3 host port.
- @uphy_dp_sel: the register of type-c phy DP select control.
- */
+struct rockchip_usb3phy_port_cfg {
- unsigned int reg;
- struct usb3phy_reg typec_conn_dir;
- struct usb3phy_reg usb3tousb2_en;
- struct usb3phy_reg external_psm;
- struct usb3phy_reg pipe_status;
- struct usb3phy_reg usb3_host_disable;
- struct usb3phy_reg usb3_host_port;
- struct usb3phy_reg uphy_dp_sel;
+};
+struct rockchip_tcphy {
- void __iomem *reg_base;
- void __iomem *grf_base;
- struct clk clk_core;
- struct clk clk_ref;
- struct reset_ctl uphy_rst;
- struct reset_ctl pipe_rst;
- struct reset_ctl tcphy_rst;
- const struct rockchip_usb3phy_port_cfg *port_cfgs;
- u8 mode;
+};
+struct phy_reg {
- u16 value;
- u32 addr;
+};
+static struct phy_reg usb3_pll_cfg[] = {
- { 0xf0, CMN_PLL0_VCOCAL_INIT },
- { 0x18, CMN_PLL0_VCOCAL_ITER },
- { 0xd0, CMN_PLL0_INTDIV },
- { 0x4a4a, CMN_PLL0_FRACDIV },
- { 0x34, CMN_PLL0_HIGH_THR },
- { 0x1ee, CMN_PLL0_SS_CTRL1 },
- { 0x7f03, CMN_PLL0_SS_CTRL2 },
- { 0x20, CMN_PLL0_DSM_DIAG },
- { 0, CMN_DIAG_PLL0_OVRD },
- { 0, CMN_DIAG_PLL0_FBH_OVRD },
- { 0, CMN_DIAG_PLL0_FBL_OVRD },
- { 0x7, CMN_DIAG_PLL0_V2I_TUNE },
- { 0x45, CMN_DIAG_PLL0_CP_TUNE },
- { 0x8, CMN_DIAG_PLL0_LF_PROG },
+};
+static inline int property_enable(struct rockchip_tcphy *priv,
const struct usb3phy_reg *reg, bool en)+{
- u32 mask = 1 << reg->write_enable;
- u32 val = en << reg->enable_bit;
- return writel(val | mask, priv->grf_base + reg->offset);
+}
+static int rockchip_tcphy_get_mode(struct rockchip_tcphy *priv) +{
- /* TODO: Add proper logic to find DP or USB3 mode */
- return MODE_DFP_USB | MODE_UFP_USB;
+}
+static void rockchip_tcphy_cfg_24m(struct rockchip_tcphy *priv) +{
- u32 i, rdata;
- /*
* cmn_ref_clk_sel = 3, select the 24Mhz for clk parent* cmn_psm_clk_dig_div = 2, set the clk division to 2*/- writel(0x830, priv->reg_base + PMA_CMN_CTRL1);
- for (i = 0; i < 4; i++) {
/** The following PHY configuration assumes a 24 MHz reference* clock.*/writel(0x90, priv->reg_base + XCVR_DIAG_LANE_FCM_EN_MGN(i));writel(0x960, priv->reg_base + TX_RCVDET_EN_TMR(i));writel(0x30, priv->reg_base + TX_RCVDET_ST_TMR(i));- }
- rdata = readl(priv->reg_base + CMN_DIAG_HSCLK_SEL);
- rdata &= ~CLK_PLL_MASK;
- rdata |= CLK_PLL_CONFIG;
- writel(rdata, priv->reg_base + CMN_DIAG_HSCLK_SEL);
+}
+static void rockchip_tcphy_cfg_usb3_pll(struct rockchip_tcphy *priv) +{
- u32 i;
- /* load the configuration of PLL0 */
- for (i = 0; i < ARRAY_SIZE(usb3_pll_cfg); i++)
writel(usb3_pll_cfg[i].value,priv->reg_base + usb3_pll_cfg[i].addr);+}
+static void rockchip_tcphy_tx_usb3_cfg_lane(struct rockchip_tcphy *priv,
u32 lane)+{
- writel(0x7799, priv->reg_base + TX_PSC_A0(lane));
- writel(0x7798, priv->reg_base + TX_PSC_A1(lane));
- writel(0x5098, priv->reg_base + TX_PSC_A2(lane));
- writel(0x5098, priv->reg_base + TX_PSC_A3(lane));
- writel(0, priv->reg_base + TX_TXCC_MGNFS_MULT_000(lane));
- writel(0xbf, priv->reg_base + XCVR_DIAG_BIDI_CTRL(lane));
+}
+static void rockchip_tcphy_rx_usb3_cfg_lane(struct rockchip_tcphy *priv,
u32 lane)+{
- writel(0xa6fd, priv->reg_base + RX_PSC_A0(lane));
- writel(0xa6fd, priv->reg_base + RX_PSC_A1(lane));
- writel(0xa410, priv->reg_base + RX_PSC_A2(lane));
- writel(0x2410, priv->reg_base + RX_PSC_A3(lane));
- writel(0x23ff, priv->reg_base + RX_PSC_CAL(lane));
- writel(0x13, priv->reg_base + RX_SIGDET_HL_FILT_TMR(lane));
- writel(0x03e7, priv->reg_base + RX_REE_CTRL_DATA_MASK(lane));
- writel(0x1004, priv->reg_base + RX_DIAG_SIGDET_TUNE(lane));
- writel(0x2010, priv->reg_base + RX_PSC_RDY(lane));
- writel(0xfb, priv->reg_base + XCVR_DIAG_BIDI_CTRL(lane));
+}
+static int rockchip_tcphy_init(struct rockchip_tcphy *priv) +{
- const struct rockchip_usb3phy_port_cfg *cfg = priv->port_cfgs;
- u32 val;
- int ret;
- ret = clk_enable(&priv->clk_core);
- if (ret) {
dev_err(phy->dev, "failed to enable core clk (ret=%d)\n", ret);return ret;- }
- ret = clk_enable(&priv->clk_ref);
- if (ret) {
dev_err(phy->dev, "failed to enable ref clk (ret=%d)\n", ret);goto err_clk_core;- }
- ret = reset_deassert(&priv->tcphy_rst);
- if (ret) {
dev_err(phy->dev, "failed to deassert uphy-tcphy reset (ret=%d)\n",ret);goto err_clk_ref;- }
- property_enable(priv, &cfg->typec_conn_dir, 0);
- rockchip_tcphy_cfg_24m(priv);
- rockchip_tcphy_cfg_usb3_pll(priv);
- rockchip_tcphy_tx_usb3_cfg_lane(priv, 0);
- rockchip_tcphy_rx_usb3_cfg_lane(priv, 1);
- ret = reset_deassert(&priv->uphy_rst);
- if (ret) {
dev_err(phy->dev, "failed to deassert uphy rst (ret=%d)\n",ret);goto err_tcphy_rst;- }
- ret = readl_poll_sleep_timeout(priv->reg_base + PMA_CMN_CTRL1,
val, val & CMN_READY, 10,PHY_MODE_SET_TIMEOUT);- if (ret < 0) {
dev_err(phy->dev, "PMA Timeout!\n");ret = -ETIMEDOUT;goto err_uphy_rst;- }
- ret = reset_deassert(&priv->pipe_rst);
- if (ret) {
dev_err(phy->dev, "failed to deassert pipe rst (ret=%d)\n",ret);goto err_uphy_rst;- }
- return 0;
+err_uphy_rst:
- reset_assert(&priv->uphy_rst);
+err_tcphy_rst:
- reset_assert(&priv->tcphy_rst);
+err_clk_ref:
- clk_disable(&priv->clk_ref);
+err_clk_core:
- clk_disable(&priv->clk_core);
- return ret;
+}
+static void rockchip_tcphy_exit(struct rockchip_tcphy *priv) +{
- reset_assert(&priv->tcphy_rst);
- reset_assert(&priv->uphy_rst);
- reset_assert(&priv->pipe_rst);
- clk_disable(&priv->clk_core);
- clk_disable(&priv->clk_ref);
+}
+static int tcphy_cfg_usb3_to_usb2_only(struct rockchip_tcphy *priv,
bool value)+{
- const struct rockchip_usb3phy_port_cfg *cfg = priv->port_cfgs;
- property_enable(priv, &cfg->usb3tousb2_en, value);
- property_enable(priv, &cfg->usb3_host_disable, value);
- property_enable(priv, &cfg->usb3_host_port, !value);
- return 0;
+}
+static int rockchip_usb3_phy_power_on(struct phy *phy) +{
- struct udevice *parent = dev_get_parent(phy->dev);
- struct rockchip_tcphy *priv = dev_get_priv(parent);
- const struct rockchip_usb3phy_port_cfg *cfg = priv->port_cfgs;
- const struct usb3phy_reg *reg = &cfg->pipe_status;
- int timeout, new_mode;
- u32 val;
- int ret;
- new_mode = rockchip_tcphy_get_mode(priv);
- if (new_mode < 0) {
dev_err(phy->dev, "invalid mode %d\n", new_mode);return new_mode;- }
- if (priv->mode == new_mode)
return 0;- if (priv->mode == MODE_DISCONNECT) {
ret = rockchip_tcphy_init(priv);if (ret) {dev_err(dev, "failed to init tcphy (ret=%d)\n", ret);return ret;}- }
- /* wait TCPHY for pipe ready */
- for (timeout = 0; timeout < 100; timeout++) {
val = readl(priv->grf_base + reg->offset);if (!(val & BIT(reg->enable_bit))) {priv->mode |= new_mode & (MODE_DFP_USB | MODE_UFP_USB);/* enable usb3 host */tcphy_cfg_usb3_to_usb2_only(priv, false);return 0;}usleep_range(10, 20);- }
- if (priv->mode == MODE_DISCONNECT)
rockchip_tcphy_exit(priv);- return -ETIMEDOUT;
+}
+static int rockchip_usb3_phy_power_off(struct phy *phy) +{
- struct udevice *parent = dev_get_parent(phy->dev);
- struct rockchip_tcphy *priv = dev_get_priv(parent);
- tcphy_cfg_usb3_to_usb2_only(priv, false);
- if (priv->mode == MODE_DISCONNECT)
goto exit;- priv->mode &= ~(MODE_UFP_USB | MODE_DFP_USB);
- if (priv->mode == MODE_DISCONNECT)
rockchip_tcphy_exit(priv);+exit:
- return 0;
+}
+static struct phy_ops rockchip_tcphy_usb3_ops = {
- .power_on = rockchip_usb3_phy_power_on,
- .power_off = rockchip_usb3_phy_power_off,
+};
+static void rockchip_tcphy_pre_init(struct udevice *dev) +{
- struct rockchip_tcphy *priv = dev_get_priv(dev);
- const struct rockchip_usb3phy_port_cfg *cfg = priv->port_cfgs;
- reset_assert(&priv->tcphy_rst);
- reset_assert(&priv->uphy_rst);
- reset_assert(&priv->pipe_rst);
- /* select external psm clock */
- property_enable(priv, &cfg->external_psm, 1);
- property_enable(priv, &cfg->usb3tousb2_en, 0);
- priv->mode = MODE_DISCONNECT;
+}
+static int rockchip_tcphy_parse_dt(struct udevice *dev) +{
- struct rockchip_tcphy *priv = dev_get_priv(dev);
- int ret;
- priv->grf_base = syscon_get_first_range(ROCKCHIP_SYSCON_GRF);
- if (IS_ERR(priv->grf_base))
return PTR_ERR(priv->grf_base);- ret = clk_get_by_name(dev, "tcpdcore", &priv->clk_core);
- if (ret) {
dev_err(dev, "failed to get tcpdcore clk (ret=%d)\n", ret);return ret;- }
- ret = clk_get_by_name(dev, "tcpdphy-ref", &priv->clk_ref);
- if (ret) {
dev_err(dev, "failed to get tcpdphy-ref clk (ret=%d)\n", ret);return ret;- }
- ret = reset_get_by_name(dev, "uphy", &priv->uphy_rst);
- if (ret) {
dev_err(dev, "failed to get uphy reset (ret=%d)\n", ret);return ret;- }
- ret = reset_get_by_name(dev, "uphy-pipe", &priv->pipe_rst);
- if (ret) {
dev_err(dev, "failed to get uphy-pipe reset (ret=%d)\n", ret);return ret;- }
- ret = reset_get_by_name(dev, "uphy-tcphy", &priv->tcphy_rst);
- if (ret) {
dev_err(dev, "failed to get uphy-tcphy reset (ret=%d)\n", ret);return ret;- }
- return 0;
+}
+static int rockchip_tcphy_probe(struct udevice *dev) +{
- struct rockchip_tcphy *priv = dev_get_priv(dev);
- const struct rockchip_usb3phy_port_cfg *phy_cfgs;
- unsigned int reg;
- int index, ret;
- priv->reg_base = (void __iomem *)dev_read_addr(dev);
- if (IS_ERR(priv->reg_base))
return PTR_ERR(priv->reg_base);- ret = dev_read_u32_index(dev, "reg", 1, ®);
- if (ret) {
dev_err(dev, "failed to read reg property (ret = %d)\n", ret);return ret;- }
- phy_cfgs = (const struct rockchip_usb3phy_port_cfg *)
dev_get_driver_data(dev);- if (!phy_cfgs)
return -EINVAL;- /* find out a proper config which can be matched with dt. */
- index = 0;
- while (phy_cfgs[index].reg) {
if (phy_cfgs[index].reg == reg) {priv->port_cfgs = &phy_cfgs[index];break;}++index;- }
- if (!priv->port_cfgs) {
dev_err(dev, "failed find proper phy-cfg\n");return -EINVAL;- }
- ret = rockchip_tcphy_parse_dt(dev);
- if (ret)
return ret;- rockchip_tcphy_pre_init(dev);
- return 0;
+}
+static int rockchip_tcphy_bind(struct udevice *dev) +{
- struct udevice *tcphy_dev;
- ofnode node;
- const char *name;
- int ret = 0;
- dev_for_each_subnode(node, dev) {
if (!ofnode_valid(node)) {dev_info(dev, "subnode %s not found\n", dev->name);return -ENXIO;}name = ofnode_get_name(node);dev_dbg(dev, "subnode %s\n", name);if (!strcasecmp(name, "dp-port")) {dev_dbg(dev, "Warning: dp-port not supported yet!\n");continue;} else if (!strcasecmp(name, "usb3-port")) {ret = device_bind_driver_to_node(dev,"rockchip_tcphy_usb3_port",name, node, &tcphy_dev);if (ret) {dev_err(dev,"'%s' cannot bind 'rockchip_tcphy_usb3_port'\n",name);return ret;}}- }
- return ret;
+}
+static const struct rockchip_usb3phy_port_cfg rk3399_typec_phy_cfgs[] = {
- {
.reg = 0xff7c0000,.typec_conn_dir = { 0xe580, 0, 16 },.usb3tousb2_en = { 0xe580, 3, 19 },.external_psm = { 0xe588, 14, 30 },.pipe_status = { 0xe5c0, 0, 0 },.usb3_host_disable = { 0x2434, 0, 16 },.usb3_host_port = { 0x2434, 12, 28 },.uphy_dp_sel = { 0x6268, 19, 19 },- },
- {
.reg = 0xff800000,.typec_conn_dir = { 0xe58c, 0, 16 },.usb3tousb2_en = { 0xe58c, 3, 19 },.external_psm = { 0xe594, 14, 30 },.pipe_status = { 0xe5c0, 16, 16 },.usb3_host_disable = { 0x2444, 0, 16 },.usb3_host_port = { 0x2444, 12, 28 },.uphy_dp_sel = { 0x6268, 3, 19 },- },
- { /* sentinel */ }
+};
+static const struct udevice_id rockchip_typec_phy_ids[] = {
- {
.compatible = "rockchip,rk3399-typec-phy",.data = (ulong)&rk3399_typec_phy_cfgs,- },
- { /* sentinel */ }
+};
+U_BOOT_DRIVER(rockchip_tcphy_usb3_port) = {
- .name = "rockchip_tcphy_usb3_port",
- .id = UCLASS_PHY,
- .ops = &rockchip_tcphy_usb3_ops,
+};
+U_BOOT_DRIVER(rockchip_typec_phy) = {
- .name = "rockchip_typec_phy",
- .id = UCLASS_PHY,
- .of_match = rockchip_typec_phy_ids,
- .probe = rockchip_tcphy_probe,
- .bind = rockchip_tcphy_bind,
- .priv_auto_alloc_size = sizeof(struct rockchip_tcphy),
+};