From: Shaohui Xie Shaohui.Xie@nxp.com
LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card
Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie Shaohui.Xie@nxp.com Signed-off-by: Mingkai Hu mingkai.hu@nxp.com Signed-off-by: Gong Qianyu Qianyu.Gong@nxp.com --- v6: - Remove lpuart support. - Move CONFIG_FSL_QSPI to defconfig and select DM_SPI_FLASH in Kconfig. v5: - Fix SPL_PAD_TO size to block aligned value. - Adjust the SPL BSS and MALLOC address. v4: - New Patch.
arch/arm/Kconfig | 13 + arch/arm/dts/Makefile | 1 + arch/arm/dts/fsl-ls1046a-qds-duart.dts | 16 + arch/arm/dts/fsl-ls1046a-qds.dtsi | 77 ++++ board/freescale/common/vid.c | 8 +- board/freescale/ls1046aqds/Kconfig | 15 + board/freescale/ls1046aqds/MAINTAINERS | 10 + board/freescale/ls1046aqds/Makefile | 9 + board/freescale/ls1046aqds/README | 70 +++ board/freescale/ls1046aqds/ddr.c | 140 ++++++ board/freescale/ls1046aqds/ddr.h | 44 ++ board/freescale/ls1046aqds/eth.c | 415 ++++++++++++++++++ board/freescale/ls1046aqds/ls1046aqds.c | 298 +++++++++++++ board/freescale/ls1046aqds/ls1046aqds_pbi.cfg | 17 + board/freescale/ls1046aqds/ls1046aqds_qixis.h | 39 ++ board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg | 7 + .../freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg | 8 + .../ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg | 8 + configs/ls1046aqds_defconfig | 28 ++ configs/ls1046aqds_nand_defconfig | 30 ++ configs/ls1046aqds_qspi_defconfig | 31 ++ configs/ls1046aqds_sdcard_ifc_defconfig | 30 ++ configs/ls1046aqds_sdcard_qspi_defconfig | 32 ++ include/configs/ls1046a_common.h | 38 +- include/configs/ls1046aqds.h | 487 +++++++++++++++++++++ 25 files changed, 1866 insertions(+), 5 deletions(-)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 8c59c42..5a5fb69 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -837,6 +837,18 @@ config TARGET_LS1043ARDB help Support for Freescale LS1043ARDB platform.
+config TARGET_LS1046AQDS + bool "Support ls1046aqds" + select ARM64 + select ARMV8_MULTIENTRY + select SUPPORT_SPL + select DM_SPI_FLASH if DM_SPI + help + Support for Freescale LS1046AQDS platform. + The LS1046A Development System (QDS) is a high-performance + development platform that supports the QorIQ LS1046A + Layerscape Architecture processor. + config TARGET_LS1046ARDB bool "Support ls1046ardb" select ARM64 @@ -992,6 +1004,7 @@ source "board/freescale/ls2080ardb/Kconfig" source "board/freescale/ls1021aqds/Kconfig" source "board/freescale/ls1043aqds/Kconfig" source "board/freescale/ls1021atwr/Kconfig" +source "board/freescale/ls1046aqds/Kconfig" source "board/freescale/ls1043ardb/Kconfig" source "board/freescale/ls1046ardb/Kconfig" source "board/freescale/ls1012aqds/Kconfig" diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index b646aa0..b635dcf 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -143,6 +143,7 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \ fsl-ls1043a-qds-lpuart.dtb \ fsl-ls1043a-rdb.dtb \ + fsl-ls1046a-qds-duart.dtb \ fsl-ls1046a-rdb.dtb \ fsl-ls1012a-qds.dtb \ fsl-ls1012a-rdb.dtb \ diff --git a/arch/arm/dts/fsl-ls1046a-qds-duart.dts b/arch/arm/dts/fsl-ls1046a-qds-duart.dts new file mode 100644 index 0000000..10a95ea --- /dev/null +++ b/arch/arm/dts/fsl-ls1046a-qds-duart.dts @@ -0,0 +1,16 @@ +/* + * Device Tree file for Freescale Layerscape-1046A family SoC. + * + * Copyright (C) 2016, Freescale Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/dts-v1/; +#include "fsl-ls1046a-qds.dtsi" + +/ { + chosen { + stdout-path = &duart0; + }; +}; diff --git a/arch/arm/dts/fsl-ls1046a-qds.dtsi b/arch/arm/dts/fsl-ls1046a-qds.dtsi new file mode 100644 index 0000000..c512293 --- /dev/null +++ b/arch/arm/dts/fsl-ls1046a-qds.dtsi @@ -0,0 +1,77 @@ +/* + * Device Tree Include file for Freescale Layerscape-1046A family SoC. + * + * Copyright (C) 2016, Freescale Semiconductor + * + * Mingkai Hu Mingkai.hu@nxp.com + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/include/ "fsl-ls1046a.dtsi" + +/ { + model = "LS1046A QDS Board"; + aliases { + spi0 = &qspi; + spi1 = &dspi0; + }; +}; + +&dspi0 { + bus-num = <0>; + status = "okay"; + + dflash0: n25q128a { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-flash"; + spi-max-frequency = <1000000>; /* input clock */ + spi-cpol; + spi-cpha; + reg = <0>; + }; + + dflash1: sst25wf040b { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-flash"; + spi-max-frequency = <3500000>; + spi-cpol; + spi-cpha; + reg = <1>; + }; + + dflash2: en25s64 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-flash"; + spi-max-frequency = <3500000>; + spi-cpol; + spi-cpha; + reg = <2>; + }; +}; + +&qspi { + bus-num = <0>; + status = "okay"; + + qflash0: s25fl128s@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-flash"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c index 2f29795..1a50304 100644 --- a/board/freescale/common/vid.c +++ b/board/freescale/common/vid.c @@ -8,7 +8,7 @@ #include <command.h> #include <i2c.h> #include <asm/io.h> -#ifdef CONFIG_LS1043A +#ifdef CONFIG_FSL_LSCH2 #include <asm/arch/immap_lsch2.h> #elif defined(CONFIG_FSL_LSCH3) #include <asm/arch/immap_lsch3.h> @@ -247,7 +247,7 @@ static int set_voltage_to_IR(int i2caddress, int vdd) * SoC before converting into an IR VID value */ vdd += board_vdd_drop_compensation(); -#ifdef CONFIG_LS1043A +#ifdef CONFIG_FSL_LSCH2 vid = DIV_ROUND_UP(vdd - 265, 5); #else vid = DIV_ROUND_UP(vdd - 245, 5); @@ -287,7 +287,7 @@ static int set_voltage(int i2caddress, int vdd) int adjust_vdd(ulong vdd_override) { int re_enable = disable_interrupts(); -#if defined(CONFIG_LS1043A) || defined(CONFIG_FSL_LSCH3) +#if defined(CONFIG_FSL_LSCH2) || defined(CONFIG_FSL_LSCH3) struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); #else ccsr_gur_t __iomem *gur = @@ -386,7 +386,7 @@ int adjust_vdd(ulong vdd_override) * | T | | | | | * ------------------------------------------------------ */ -#ifdef CONFIG_LS1043A +#ifdef CONFIG_FSL_LSCH2 vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_ALTVID_SHIFT) & FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK; if ((vid == 0) || (vid == FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK)) { diff --git a/board/freescale/ls1046aqds/Kconfig b/board/freescale/ls1046aqds/Kconfig new file mode 100644 index 0000000..723f4ba --- /dev/null +++ b/board/freescale/ls1046aqds/Kconfig @@ -0,0 +1,15 @@ +if TARGET_LS1046AQDS + +config SYS_BOARD + default "ls1046aqds" + +config SYS_VENDOR + default "freescale" + +config SYS_SOC + default "fsl-layerscape" + +config SYS_CONFIG_NAME + default "ls1046aqds" + +endif diff --git a/board/freescale/ls1046aqds/MAINTAINERS b/board/freescale/ls1046aqds/MAINTAINERS new file mode 100644 index 0000000..b4549ae --- /dev/null +++ b/board/freescale/ls1046aqds/MAINTAINERS @@ -0,0 +1,10 @@ +LS1046AQDS BOARD +M: Mingkai Hu Mingkai.Hu@nxp.com +S: Maintained +F: board/freescale/ls1046aqds/ +F: include/configs/ls1046aqds.h +F: configs/ls1046aqds_defconfig +F: configs/ls1046aqds_nand_defconfig +F: configs/ls1046aqds_sdcard_ifc_defconfig +F: configs/ls1046aqds_sdcard_qspi_defconfig +F: configs/ls1046aqds_qspi_defconfig diff --git a/board/freescale/ls1046aqds/Makefile b/board/freescale/ls1046aqds/Makefile new file mode 100644 index 0000000..df6e546 --- /dev/null +++ b/board/freescale/ls1046aqds/Makefile @@ -0,0 +1,9 @@ +# +# Copyright 2016 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += ddr.o +obj-y += eth.o +obj-y += ls1046aqds.o diff --git a/board/freescale/ls1046aqds/README b/board/freescale/ls1046aqds/README new file mode 100644 index 0000000..b8fa326 --- /dev/null +++ b/board/freescale/ls1046aqds/README @@ -0,0 +1,70 @@ +Overview +-------- +The LS1046A Development System (QDS) is a high-performance computing, +evaluation, and development platform that supports the QorIQ LS1046A +LayerScape Architecture processor. The LS1046AQDS provides SW development +platform for the Freescale LS1046A processor series, with a complete +debugging environment. + +LS1046A SoC Overview +-------------------- +Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS1046A +SoC overview. + + LS1046AQDS board Overview + ----------------------- + - SERDES Connections, 8 lanes supporting: + - PCI Express - 3.0 + - SGMII, SGMII 2.5 + - QSGMII + - SATA 3.0 + - XFI + - DDR Controller + - 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s + -IFC/Local Bus + - One in-socket 128 MB NOR flash 16-bit data bus + - One 512 MB NAND flash with ECC support + - PromJet Port + - FPGA connection + - USB 3.0 + - Three high speed USB 3.0 ports + - First USB 3.0 port configured as Host with Type-A connector + - The other two USB 3.0 ports configured as OTG with micro-AB connector + - SDHC port connects directly to an adapter card slot, featuring: + - Optional clock feedback paths, and optional high-speed voltage translation assistance + - SD slots for SD, SDHC (1x, 4x, 8x), and/or MMC + - eMMC memory devices + - DSPI: Onboard support for three SPI flash memory devices + - 4 I2C controllers + - One SATA onboard connectors + - UART + - Two 4-pin serial ports at up to 115.2 Kbit/s + - Two DB9 D-Type connectors supporting one Serial port each + - ARM JTAG support + +Memory map from core's view +---------------------------- +Start Address End Address Description Size +0x00_0000_0000 - 0x00_000F_FFFF Secure Boot ROM 1MB +0x00_0100_0000 - 0x00_0FFF_FFFF CCSRBAR 240MB +0x00_1000_0000 - 0x00_1000_FFFF OCRAM0 64KB +0x00_1001_0000 - 0x00_1001_FFFF OCRAM1 64KB +0x00_2000_0000 - 0x00_20FF_FFFF DCSR 16MB +0x00_6000_0000 - 0x00_67FF_FFFF IFC - NOR Flash 128MB +0x00_7E80_0000 - 0x00_7E80_FFFF IFC - NAND Flash 64KB +0x00_7FB0_0000 - 0x00_7FB0_0FFF IFC - FPGA 4KB +0x00_8000_0000 - 0x00_FFFF_FFFF DRAM1 2GB +0x05_0000_0000 - 0x05_07FF_FFFF QMAN S/W Portal 128M +0x05_0800_0000 - 0x05_0FFF_FFFF BMAN S/W Portal 128M +0x08_8000_0000 - 0x09_FFFF_FFFF DRAM2 6GB +0x40_0000_0000 - 0x47_FFFF_FFFF PCI Express1 32G +0x48_0000_0000 - 0x4F_FFFF_FFFF PCI Express2 32G +0x50_0000_0000 - 0x57_FFFF_FFFF PCI Express3 32G + +Booting Options +--------------- +a) Promjet Boot +b) NOR boot +c) NAND boot +d) SD boot +e) QSPI boot diff --git a/board/freescale/ls1046aqds/ddr.c b/board/freescale/ls1046aqds/ddr.c new file mode 100644 index 0000000..d813965 --- /dev/null +++ b/board/freescale/ls1046aqds/ddr.c @@ -0,0 +1,140 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#ifdef CONFIG_FSL_DEEP_SLEEP +#include <fsl_sleep.h> +#endif +#include "ddr.h" + +DECLARE_GLOBAL_DATA_PTR; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 3) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found for %lu MT/s\n", + ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); + + popts->data_bus_width = 0; /* 64b data bus */ + popts->otf_burst_chop_en = 0; + popts->burst_length = DDR_BL8; + popts->bstopre = 0; /* enable auto precharge */ + + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) | + DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2; +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + +#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD) + return fsl_ddr_sdram_size(); +#else + puts("Initializing DDR....using SPD\n"); + + dram_size = fsl_ddr_sdram(); +#endif + +#ifdef CONFIG_FSL_DEEP_SLEEP + fsl_dp_ddr_restore(); +#endif + + erratum_a008850_post(); + + return dram_size; +} + +void dram_init_banksize(void) +{ + /* + * gd->arch.secure_ram tracks the location of secure memory. + * It was set as if the memory starts from 0. + * The address needs to add the offset of its bank. + */ + gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; + if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) { + gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE; + gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE; + gd->bd->bi_dram[1].size = gd->ram_size - + CONFIG_SYS_DDR_BLOCK1_SIZE; +#ifdef CONFIG_SYS_MEM_RESERVE_SECURE + gd->arch.secure_ram = gd->bd->bi_dram[1].start + + gd->arch.secure_ram - + CONFIG_SYS_DDR_BLOCK1_SIZE; + gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED; +#endif + } else { + gd->bd->bi_dram[0].size = gd->ram_size; +#ifdef CONFIG_SYS_MEM_RESERVE_SECURE + gd->arch.secure_ram = gd->bd->bi_dram[0].start + + gd->arch.secure_ram; + gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED; +#endif + } +} diff --git a/board/freescale/ls1046aqds/ddr.h b/board/freescale/ls1046aqds/ddr.h new file mode 100644 index 0000000..b594032 --- /dev/null +++ b/board/freescale/ls1046aqds/ddr.h @@ -0,0 +1,44 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DDR_H__ +#define __DDR_H__ + +void erratum_a008850_post(void); + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; +}; + +/* + * These tables contain all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | + */ + {2, 1350, 0, 8, 6, 0x0708090B, 0x0C0D0E09,}, + {2, 1666, 0, 8, 7, 0x08090A0C, 0x0D0F100B,}, + {2, 1900, 0, 8, 7, 0x09090B0D, 0x0E10120B,}, + {2, 2300, 0, 8, 9, 0x0A0C0D11, 0x1214150E,}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; + +#endif diff --git a/board/freescale/ls1046aqds/eth.c b/board/freescale/ls1046aqds/eth.c new file mode 100644 index 0000000..046db11 --- /dev/null +++ b/board/freescale/ls1046aqds/eth.c @@ -0,0 +1,415 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <netdev.h> +#include <fdt_support.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <fsl_dtsec.h> +#include <malloc.h> +#include <asm/arch/fsl_serdes.h> + +#include "../common/qixis.h" +#include "../common/fman.h" +#include "ls1046aqds_qixis.h" + +#define EMI_NONE 0xFF +#define EMI1_RGMII1 0 +#define EMI1_RGMII2 1 +#define EMI1_SLOT1 2 +#define EMI1_SLOT2 3 +#define EMI1_SLOT4 4 + +static int mdio_mux[NUM_FM_PORTS]; + +static const char * const mdio_names[] = { + "LS1046AQDS_MDIO_RGMII1", + "LS1046AQDS_MDIO_RGMII2", + "LS1046AQDS_MDIO_SLOT1", + "LS1046AQDS_MDIO_SLOT2", + "LS1046AQDS_MDIO_SLOT4", + "NULL", +}; + +/* Map SerDes 1 & 2 lanes to default slot. */ +static u8 lane_to_slot[] = {1, 1, 1, 1, 0, 4, 0 , 0}; + +static const char *ls1046aqds_mdio_name_for_muxval(u8 muxval) +{ + return mdio_names[muxval]; +} + +struct mii_dev *mii_dev_for_muxval(u8 muxval) +{ + struct mii_dev *bus; + const char *name; + + if (muxval > EMI1_SLOT4) + return NULL; + + name = ls1046aqds_mdio_name_for_muxval(muxval); + + if (!name) { + printf("No bus for muxval %x\n", muxval); + return NULL; + } + + bus = miiphy_get_dev_by_name(name); + + if (!bus) { + printf("No bus by name %s\n", name); + return NULL; + } + + return bus; +} + +struct ls1046aqds_mdio { + u8 muxval; + struct mii_dev *realbus; +}; + +static void ls1046aqds_mux_mdio(u8 muxval) +{ + u8 brdcfg4; + + if (muxval < 7) { + brdcfg4 = QIXIS_READ(brdcfg[4]); + brdcfg4 &= ~BRDCFG4_EMISEL_MASK; + brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT); + QIXIS_WRITE(brdcfg[4], brdcfg4); + } +} + +static int ls1046aqds_mdio_read(struct mii_dev *bus, int addr, int devad, + int regnum) +{ + struct ls1046aqds_mdio *priv = bus->priv; + + ls1046aqds_mux_mdio(priv->muxval); + + return priv->realbus->read(priv->realbus, addr, devad, regnum); +} + +static int ls1046aqds_mdio_write(struct mii_dev *bus, int addr, int devad, + int regnum, u16 value) +{ + struct ls1046aqds_mdio *priv = bus->priv; + + ls1046aqds_mux_mdio(priv->muxval); + + return priv->realbus->write(priv->realbus, addr, devad, + regnum, value); +} + +static int ls1046aqds_mdio_reset(struct mii_dev *bus) +{ + struct ls1046aqds_mdio *priv = bus->priv; + + return priv->realbus->reset(priv->realbus); +} + +static int ls1046aqds_mdio_init(char *realbusname, u8 muxval) +{ + struct ls1046aqds_mdio *pmdio; + struct mii_dev *bus = mdio_alloc(); + + if (!bus) { + printf("Failed to allocate ls1046aqds MDIO bus\n"); + return -1; + } + + pmdio = malloc(sizeof(*pmdio)); + if (!pmdio) { + printf("Failed to allocate ls1046aqds private data\n"); + free(bus); + return -1; + } + + bus->read = ls1046aqds_mdio_read; + bus->write = ls1046aqds_mdio_write; + bus->reset = ls1046aqds_mdio_reset; + sprintf(bus->name, ls1046aqds_mdio_name_for_muxval(muxval)); + + pmdio->realbus = miiphy_get_dev_by_name(realbusname); + + if (!pmdio->realbus) { + printf("No bus with name %s\n", realbusname); + free(bus); + free(pmdio); + return -1; + } + + pmdio->muxval = muxval; + bus->priv = pmdio; + return mdio_register(bus); +} + +void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, + enum fm_port port, int offset) +{ + struct fixed_link f_link; + + if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) { + switch (port) { + case FM1_DTSEC9: + fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p1"); + break; + case FM1_DTSEC10: + fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p2"); + break; + case FM1_DTSEC5: + fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p3"); + break; + case FM1_DTSEC6: + fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p4"); + break; + case FM1_DTSEC2: + fdt_set_phy_handle(fdt, compat, addr, "sgmii_s4_p1"); + break; + default: + break; + } + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) { + /* 2.5G SGMII interface */ + f_link.phy_id = cpu_to_fdt32(port); + f_link.duplex = cpu_to_fdt32(1); + f_link.link_speed = cpu_to_fdt32(1000); + f_link.pause = 0; + f_link.asym_pause = 0; + /* no PHY for 2.5G SGMII on QDS */ + fdt_delprop(fdt, offset, "phy-handle"); + fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link)); + fdt_setprop_string(fdt, offset, "phy-connection-type", + "sgmii-2500"); + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) { + switch (port) { + case FM1_DTSEC1: + fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p4"); + break; + case FM1_DTSEC5: + fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p2"); + break; + case FM1_DTSEC6: + fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p1"); + break; + case FM1_DTSEC10: + fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p3"); + break; + default: + break; + } + fdt_delprop(fdt, offset, "phy-connection-type"); + fdt_setprop_string(fdt, offset, "phy-connection-type", + "qsgmii"); + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII && + (port == FM1_10GEC1 || port == FM1_10GEC2)) { + /* XFI interface */ + f_link.phy_id = cpu_to_fdt32(port); + f_link.duplex = cpu_to_fdt32(1); + f_link.link_speed = cpu_to_fdt32(10000); + f_link.pause = 0; + f_link.asym_pause = 0; + /* no PHY for XFI */ + fdt_delprop(fdt, offset, "phy-handle"); + fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link)); + fdt_setprop_string(fdt, offset, "phy-connection-type", "xgmii"); + } +} + +void fdt_fixup_board_enet(void *fdt) +{ + int i; + + for (i = FM1_DTSEC1; i < NUM_FM_PORTS; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_SGMII: + case PHY_INTERFACE_MODE_QSGMII: + switch (mdio_mux[i]) { + case EMI1_SLOT1: + fdt_status_okay_by_alias(fdt, "emi1_slot1"); + break; + case EMI1_SLOT2: + fdt_status_okay_by_alias(fdt, "emi1_slot2"); + break; + case EMI1_SLOT4: + fdt_status_okay_by_alias(fdt, "emi1_slot4"); + break; + default: + break; + } + break; + default: + break; + } + } +} + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_FMAN_ENET + int i, idx, lane, slot, interface; + struct memac_mdio_info dtsec_mdio_info; + struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 srds_s1, srds_s2; + u8 brdcfg12; + + srds_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK; + srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT; + + srds_s2 = in_be32(&gur->rcwsr[4]) & + FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK; + srds_s2 >>= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT; + + /* Initialize the mdio_mux array so we can recognize empty elements */ + for (i = 0; i < NUM_FM_PORTS; i++) + mdio_mux[i] = EMI_NONE; + + dtsec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; + + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the 1G MDIO bus */ + fm_memac_mdio_init(bis, &dtsec_mdio_info); + + /* Register the muxing front-ends to the MDIO buses */ + ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1); + ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2); + ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1); + ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2); + ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4); + + /* Set the two on-board RGMII PHY address */ + fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR); + + switch (srds_s1) { + case 0x3333: + /* SGMII on slot 1, MAC 9 */ + fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR); + case 0x1333: + case 0x2333: + /* SGMII on slot 1, MAC 10 */ + fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR); + case 0x1133: + case 0x2233: + /* SGMII on slot 1, MAC 5/6 */ + fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR); + break; + case 0x1040: + case 0x2040: + /* QSGMII on lane B, MAC 6/5/10/1 */ + fm_info_set_phy_address(FM1_DTSEC6, + QSGMII_CARD_PORT1_PHY_ADDR_S2); + fm_info_set_phy_address(FM1_DTSEC5, + QSGMII_CARD_PORT2_PHY_ADDR_S2); + fm_info_set_phy_address(FM1_DTSEC10, + QSGMII_CARD_PORT3_PHY_ADDR_S2); + fm_info_set_phy_address(FM1_DTSEC1, + QSGMII_CARD_PORT4_PHY_ADDR_S2); + break; + case 0x3363: + /* SGMII on slot 1, MAC 9/10 */ + fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR); + case 0x1163: + case 0x2263: + case 0x2223: + /* SGMII on slot 1, MAC 6 */ + fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR); + break; + default: + printf("Invalid SerDes protocol 0x%x for LS1046AQDS\n", + srds_s1); + break; + } + + if (srds_s2 == 0x5a59 || srds_s2 == 0x5a06) + /* SGMII on slot 4, MAC 2 */ + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + idx = i - FM1_DTSEC1; + interface = fm_info_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_SGMII: + case PHY_INTERFACE_MODE_QSGMII: + if (interface == PHY_INTERFACE_MODE_SGMII) { + if (i == FM1_DTSEC5) { + /* route lane 2 to slot1 so to have + * one sgmii riser card supports + * MAC5 and MAC6. + */ + brdcfg12 = QIXIS_READ(brdcfg[12]); + QIXIS_WRITE(brdcfg[12], + brdcfg12 | 0x80); + } + lane = serdes_get_first_lane(FSL_SRDS_1, + SGMII_FM1_DTSEC1 + idx); + } else { + /* clear the bit 7 to route lane B on slot2. */ + brdcfg12 = QIXIS_READ(brdcfg[12]); + QIXIS_WRITE(brdcfg[12], brdcfg12 & 0x7f); + + lane = serdes_get_first_lane(FSL_SRDS_1, + QSGMII_FM1_A); + lane_to_slot[lane] = 2; + } + + if (i == FM1_DTSEC2) + lane = 5; + + if (lane < 0) + break; + + slot = lane_to_slot[lane]; + debug("FM1@DTSEC%u expects SGMII in slot %u\n", + idx + 1, slot); + if (QIXIS_READ(present2) & (1 << (slot - 1))) + fm_disable_port(i); + + switch (slot) { + case 1: + mdio_mux[i] = EMI1_SLOT1; + fm_info_set_mdio(i, mii_dev_for_muxval( + mdio_mux[i])); + break; + case 2: + mdio_mux[i] = EMI1_SLOT2; + fm_info_set_mdio(i, mii_dev_for_muxval( + mdio_mux[i])); + break; + case 4: + mdio_mux[i] = EMI1_SLOT4; + fm_info_set_mdio(i, mii_dev_for_muxval( + mdio_mux[i])); + break; + default: + break; + } + break; + case PHY_INTERFACE_MODE_RGMII: + if (i == FM1_DTSEC3) + mdio_mux[i] = EMI1_RGMII1; + else if (i == FM1_DTSEC4) + mdio_mux[i] = EMI1_RGMII2; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + default: + break; + } + } + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ + + return pci_eth_init(bis); +} diff --git a/board/freescale/ls1046aqds/ls1046aqds.c b/board/freescale/ls1046aqds/ls1046aqds.c new file mode 100644 index 0000000..8c18538 --- /dev/null +++ b/board/freescale/ls1046aqds/ls1046aqds.c @@ -0,0 +1,298 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <fdt_support.h> +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/fsl_serdes.h> +#include <asm/arch/fdt.h> +#include <asm/arch/soc.h> +#include <ahci.h> +#include <hwconfig.h> +#include <mmc.h> +#include <scsi.h> +#include <fm_eth.h> +#include <fsl_csu.h> +#include <fsl_esdhc.h> +#include <fsl_ifc.h> +#include <spl.h> + +#include "../common/vid.h" +#include "../common/qixis.h" +#include "ls1046aqds_qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +enum { + MUX_TYPE_GPIO, +}; + +int checkboard(void) +{ + char buf[64]; +#ifndef CONFIG_SD_BOOT + u8 sw; +#endif + + puts("Board: LS1046AQDS, boot from "); + +#ifdef CONFIG_SD_BOOT + puts("SD\n"); +#else + sw = QIXIS_READ(brdcfg[0]); + sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; + + if (sw < 0x8) + printf("vBank: %d\n", sw); + else if (sw == 0x8) + puts("PromJet\n"); + else if (sw == 0x9) + puts("NAND\n"); + else if (sw == 0xF) + printf("QSPI\n"); + else + printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); +#endif + + printf("Sys ID: 0x%02x, Sys Ver: 0x%02x\n", + QIXIS_READ(id), QIXIS_READ(arch)); + + printf("FPGA: v%d (%s), build %d\n", + (int)QIXIS_READ(scver), qixis_read_tag(buf), + (int)qixis_read_minor()); + + return 0; +} + +bool if_board_diff_clk(void) +{ + u8 diff_conf = QIXIS_READ(brdcfg[11]); + + return diff_conf & 0x40; +} + +unsigned long get_board_sys_clk(void) +{ + u8 sysclk_conf = QIXIS_READ(brdcfg[1]); + + switch (sysclk_conf & 0x0f) { + case QIXIS_SYSCLK_64: + return 64000000; + case QIXIS_SYSCLK_83: + return 83333333; + case QIXIS_SYSCLK_100: + return 100000000; + case QIXIS_SYSCLK_125: + return 125000000; + case QIXIS_SYSCLK_133: + return 133333333; + case QIXIS_SYSCLK_150: + return 150000000; + case QIXIS_SYSCLK_160: + return 160000000; + case QIXIS_SYSCLK_166: + return 166666666; + } + + return 66666666; +} + +unsigned long get_board_ddr_clk(void) +{ + u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); + + if (if_board_diff_clk()) + return get_board_sys_clk(); + switch ((ddrclk_conf & 0x30) >> 4) { + case QIXIS_DDRCLK_100: + return 100000000; + case QIXIS_DDRCLK_125: + return 125000000; + case QIXIS_DDRCLK_133: + return 133333333; + } + + return 66666666; +} + +int select_i2c_ch_pca9547(u8 ch) +{ + int ret; + + ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); + if (ret) { + puts("PCA: failed to select proper channel\n"); + return ret; + } + + return 0; +} + +int dram_init(void) +{ + /* + * When resuming from deep sleep, the I2C channel may not be + * in the default channel. So, switch to the default channel + * before accessing DDR SPD. + */ + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + gd->ram_size = initdram(0); + + return 0; +} + +int i2c_multiplexer_select_vid_channel(u8 channel) +{ + return select_i2c_ch_pca9547(channel); +} + +int board_early_init_f(void) +{ +#ifdef CONFIG_HAS_FSL_XHCI_USB + struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; + u32 usb_pwrfault; +#endif + +#ifdef CONFIG_SYS_I2C_EARLY_INIT + i2c_early_init_f(); +#endif + fsl_lsch2_early_init_f(); + +#ifdef CONFIG_HAS_FSL_XHCI_USB + out_be32(&scfg->rcwpmuxcr0, 0x3333); + out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1); + usb_pwrfault = (SCFG_USBPWRFAULT_DEDICATED << + SCFG_USBPWRFAULT_USB3_SHIFT) | + (SCFG_USBPWRFAULT_DEDICATED << + SCFG_USBPWRFAULT_USB2_SHIFT) | + (SCFG_USBPWRFAULT_SHARED << + SCFG_USBPWRFAULT_USB1_SHIFT); + out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault); +#endif + + return 0; +} + +#ifdef CONFIG_FSL_DEEP_SLEEP +/* determine if it is a warm boot */ +bool is_warm_boot(void) +{ +#define DCFG_CCSR_CRSTSR_WDRFR (1 << 3) + struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR; + + if (in_be32(&gur->crstsr) & DCFG_CCSR_CRSTSR_WDRFR) + return 1; + + return 0; +} +#endif + +int config_board_mux(int ctrl_type) +{ + u8 reg14; + + reg14 = QIXIS_READ(brdcfg[14]); + + switch (ctrl_type) { + case MUX_TYPE_GPIO: + reg14 = (reg14 & (~0x6)) | 0x2; + break; + default: + puts("Unsupported mux interface type\n"); + return -1; + } + + QIXIS_WRITE(brdcfg[14], reg14); + + return 0; +} + +int config_serdes_mux(void) +{ + return 0; +} + +#ifdef CONFIG_MISC_INIT_R +int misc_init_r(void) +{ + if (hwconfig("gpio")) + config_board_mux(MUX_TYPE_GPIO); + + return 0; +} +#endif + +int board_init(void) +{ + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + +#ifdef CONFIG_SYS_FSL_SERDES + config_serdes_mux(); +#endif + +#ifdef CONFIG_LAYERSCAPE_NS_ACCESS + enable_layerscape_ns_access(); +#endif + + if (adjust_vdd(0)) + printf("Warning: Adjusting core voltage failed.\n"); + + return 0; +} + +#ifdef CONFIG_OF_BOARD_SETUP +int ft_board_setup(void *blob, bd_t *bd) +{ + u64 base[CONFIG_NR_DRAM_BANKS]; + u64 size[CONFIG_NR_DRAM_BANKS]; + u8 reg; + + /* fixup DT for the two DDR banks */ + base[0] = gd->bd->bi_dram[0].start; + size[0] = gd->bd->bi_dram[0].size; + base[1] = gd->bd->bi_dram[1].start; + size[1] = gd->bd->bi_dram[1].size; + + fdt_fixup_memory_banks(blob, base, size, 2); + ft_cpu_setup(blob, bd); + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif + + reg = QIXIS_READ(brdcfg[0]); + reg = (reg & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; + + /* Disable IFC if QSPI is enabled */ + if (reg == 0xF) + do_fixup_by_compat(blob, "fsl,ifc", + "status", "disabled", 8 + 1, 1); + + return 0; +} +#endif + +u8 flash_read8(void *addr) +{ + return __raw_readb(addr + 1); +} + +void flash_write16(u16 val, void *addr) +{ + u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00)); + + __raw_writew(shftval, addr); +} + +u16 flash_read16(void *addr) +{ + u16 val = __raw_readw(addr); + + return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00); +} diff --git a/board/freescale/ls1046aqds/ls1046aqds_pbi.cfg b/board/freescale/ls1046aqds/ls1046aqds_pbi.cfg new file mode 100644 index 0000000..5a6b7b8 --- /dev/null +++ b/board/freescale/ls1046aqds/ls1046aqds_pbi.cfg @@ -0,0 +1,17 @@ +#Configure Scratch register +09570600 00000000 +09570604 10000000 +#Alt base register +09570158 00001000 +#Disable CCI barrier tranaction +09570178 0000e010 +09180000 00000008 +#USB PHY frequency sel +09570418 0000009e +0957041c 0000009e +09570420 0000009e +#Serdes SATA +09eb1300 80104e20 +09eb08dc 00502880 +#flush PBI data +096100c0 000fffff diff --git a/board/freescale/ls1046aqds/ls1046aqds_qixis.h b/board/freescale/ls1046aqds/ls1046aqds_qixis.h new file mode 100644 index 0000000..58ab132 --- /dev/null +++ b/board/freescale/ls1046aqds/ls1046aqds_qixis.h @@ -0,0 +1,39 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __LS1046AQDS_QIXIS_H__ +#define __LS1046AQDS_QIXIS_H__ + +/* Definitions of QIXIS Registers for LS1046AQDS */ + +/* BRDCFG4[4:7] select EC1 and EC2 as a pair */ +#define BRDCFG4_EMISEL_MASK 0xe0 +#define BRDCFG4_EMISEL_SHIFT 5 + +/* SYSCLK */ +#define QIXIS_SYSCLK_66 0x0 +#define QIXIS_SYSCLK_83 0x1 +#define QIXIS_SYSCLK_100 0x2 +#define QIXIS_SYSCLK_125 0x3 +#define QIXIS_SYSCLK_133 0x4 +#define QIXIS_SYSCLK_150 0x5 +#define QIXIS_SYSCLK_160 0x6 +#define QIXIS_SYSCLK_166 0x7 +#define QIXIS_SYSCLK_64 0x8 + +/* DDRCLK */ +#define QIXIS_DDRCLK_66 0x0 +#define QIXIS_DDRCLK_100 0x1 +#define QIXIS_DDRCLK_125 0x2 +#define QIXIS_DDRCLK_133 0x3 + +/* BRDCFG2 - SD clock*/ +#define QIXIS_SDCLK1_100 0x0 +#define QIXIS_SDCLK1_125 0x1 +#define QIXIS_SDCLK1_165 0x2 +#define QIXIS_SDCLK1_100_SP 0x3 + +#endif diff --git a/board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg b/board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg new file mode 100644 index 0000000..b5fc08c --- /dev/null +++ b/board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg @@ -0,0 +1,7 @@ +#PBL preamble and RCW header +aa55aa55 01ee0100 +# serdes protocol +0c150010 0e000000 00000000 00000000 +11335559 40005012 e0116000 c1000000 +00000000 00000000 00000000 00038800 +00000000 01001101 00000096 00000001 diff --git a/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg b/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg new file mode 100644 index 0000000..59d24d6 --- /dev/null +++ b/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg @@ -0,0 +1,8 @@ +#PBL preamble and RCW header +aa55aa55 01ee0100 +# RCW +# Enable IFC; disable QSPI +0c150010 0e000000 00000000 00000000 +11335559 40005012 60040000 c1000000 +00000000 00000000 00000000 00038800 +00000000 01001101 00000096 00000001 diff --git a/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg b/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg new file mode 100644 index 0000000..9401a6f --- /dev/null +++ b/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg @@ -0,0 +1,8 @@ +#PBL preamble and RCW header +aa55aa55 01ee0100 +# RCW +# Enable QSPI; disable IFC +0c150010 0e000000 00000000 00000000 +11335559 40005012 60040000 c1000000 +00000000 00000000 00000000 00038800 +20124000 01001101 00000096 00000001 diff --git a/configs/ls1046aqds_defconfig b/configs/ls1046aqds_defconfig new file mode 100644 index 0000000..71c3b95 --- /dev/null +++ b/configs/ls1046aqds_defconfig @@ -0,0 +1,28 @@ +CONFIG_ARM=y +CONFIG_TARGET_LS1046AQDS=y +CONFIG_DM_SPI=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart" +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4" +CONFIG_BOOTDELAY=10 +CONFIG_HUSH_PARSER=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_I2C=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_DM=y +CONFIG_SPI_FLASH=y +CONFIG_SYS_NS16550=y +CONFIG_FSL_DSPI=y diff --git a/configs/ls1046aqds_nand_defconfig b/configs/ls1046aqds_nand_defconfig new file mode 100644 index 0000000..b29796d --- /dev/null +++ b/configs/ls1046aqds_nand_defconfig @@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_TARGET_LS1046AQDS=y +CONFIG_DM_SPI=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart" +CONFIG_SPL=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,RAMBOOT_PBL,SPL_FSL_PBL" +CONFIG_NAND_BOOT=y +CONFIG_BOOTDELAY=10 +CONFIG_HUSH_PARSER=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_I2C=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_DM=y +CONFIG_SPI_FLASH=y +CONFIG_SYS_NS16550=y +CONFIG_FSL_DSPI=y diff --git a/configs/ls1046aqds_qspi_defconfig b/configs/ls1046aqds_qspi_defconfig new file mode 100644 index 0000000..bdcb2d1 --- /dev/null +++ b/configs/ls1046aqds_qspi_defconfig @@ -0,0 +1,31 @@ +CONFIG_ARM=y +CONFIG_TARGET_LS1046AQDS=y +CONFIG_DM_SPI=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart" +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4" +CONFIG_QSPI_BOOT=y +CONFIG_BOOTDELAY=10 +CONFIG_HUSH_PARSER=y +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_IMLS is not set +CONFIG_CMD_GREPENV=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_I2C=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_DM=y +CONFIG_SPI_FLASH=y +CONFIG_SYS_NS16550=y +CONFIG_FSL_DSPI=y +CONFIG_FSL_QSPI=y diff --git a/configs/ls1046aqds_sdcard_ifc_defconfig b/configs/ls1046aqds_sdcard_ifc_defconfig new file mode 100644 index 0000000..044bd6e --- /dev/null +++ b/configs/ls1046aqds_sdcard_ifc_defconfig @@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_TARGET_LS1046AQDS=y +CONFIG_DM_SPI=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart" +CONFIG_SPL=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,RAMBOOT_PBL,SPL_FSL_PBL" +CONFIG_SD_BOOT=y +CONFIG_BOOTDELAY=10 +CONFIG_HUSH_PARSER=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_I2C=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_DM=y +CONFIG_SPI_FLASH=y +CONFIG_SYS_NS16550=y +CONFIG_FSL_DSPI=y diff --git a/configs/ls1046aqds_sdcard_qspi_defconfig b/configs/ls1046aqds_sdcard_qspi_defconfig new file mode 100644 index 0000000..cb8e635 --- /dev/null +++ b/configs/ls1046aqds_sdcard_qspi_defconfig @@ -0,0 +1,32 @@ +CONFIG_ARM=y +CONFIG_TARGET_LS1046AQDS=y +CONFIG_DM_SPI=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart" +CONFIG_SPL=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT_QSPI" +CONFIG_SD_BOOT=y +CONFIG_BOOTDELAY=10 +CONFIG_HUSH_PARSER=y +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_IMLS is not set +CONFIG_CMD_GREPENV=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_I2C=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_DM=y +CONFIG_SPI_FLASH=y +CONFIG_SYS_NS16550=y +CONFIG_FSL_DSPI=y +CONFIG_FSL_QSPI=y diff --git a/include/configs/ls1046a_common.h b/include/configs/ls1046a_common.h index 9ee29b4..5856de8 100644 --- a/include/configs/ls1046a_common.h +++ b/include/configs/ls1046a_common.h @@ -80,6 +80,36 @@ #define CONFIG_SYS_MONITOR_LEN 0xa0000 #endif
+/* NAND SPL */ +#ifdef CONFIG_NAND_BOOT +#define CONFIG_SPL_PBL_PAD +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_WATCHDOG_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT + +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +#define CONFIG_SPL_TEXT_BASE 0x10000000 +#define CONFIG_SPL_MAX_SIZE 0x1d000 /* 116 KiB */ +#define CONFIG_SPL_STACK 0x1001f000 +#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE + +#define CONFIG_SPL_BSS_START_ADDR 0x8f000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ + CONFIG_SPL_BSS_MAX_SIZE) +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 +#define CONFIG_SYS_MONITOR_LEN 0xa0000 +#endif + /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC @@ -117,13 +147,19 @@ */ #define CONFIG_SYS_QE_FMAN_FW_IN_MMC #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) -#else +#elif defined(CONFIG_QSPI_BOOT) #define CONFIG_SYS_QE_FW_IN_SPIFLASH #define CONFIG_SYS_FMAN_FW_ADDR 0x40300000 #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_CS 0 #define CONFIG_ENV_SPI_MAX_HZ 1000000 #define CONFIG_ENV_SPI_MODE 0x03 +#elif defined(CONFIG_NAND_BOOT) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_FMAN_FW_ADDR 0x60300000 #endif #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) diff --git a/include/configs/ls1046aqds.h b/include/configs/ls1046aqds.h new file mode 100644 index 0000000..2e5c2f1 --- /dev/null +++ b/include/configs/ls1046aqds.h @@ -0,0 +1,487 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __LS1046AQDS_H__ +#define __LS1046AQDS_H__ + +#include "ls1046a_common.h" + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT) +#define CONFIG_SYS_TEXT_BASE 0x82000000 +#elif defined(CONFIG_QSPI_BOOT) +#define CONFIG_SYS_TEXT_BASE 0x40010000 +#else +#define CONFIG_SYS_TEXT_BASE 0x60100000 +#endif + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +unsigned long get_board_ddr_clk(void); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() + +#define CONFIG_SKIP_LOWLEVEL_INIT + +#define CONFIG_LAYERSCAPE_NS_ACCESS + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +/* Physical Memory Map */ +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 +#define CONFIG_NR_DRAM_BANKS 2 + +#define CONFIG_DDR_SPD +#define SPD_EEPROM_ADDRESS 0x51 +#define CONFIG_SYS_SPD_BUS_NUM 0 + +#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ + +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_SYS_HAS_SERDES + +/* DSPI */ +#ifdef CONFIG_FSL_DSPI +#define CONFIG_SPI_FLASH_STMICRO /* cs0 */ +#define CONFIG_SPI_FLASH_SST /* cs1 */ +#define CONFIG_SPI_FLASH_EON /* cs2 */ +#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) +#define CONFIG_SF_DEFAULT_BUS 1 +#define CONFIG_SF_DEFAULT_CS 0 +#endif +#endif + +/* QSPI */ +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) +#ifdef CONFIG_FSL_QSPI +#define CONFIG_SPI_FLASH_SPANSION +#define FSL_QSPI_FLASH_SIZE (1 << 24) +#define FSL_QSPI_FLASH_NUM 2 +#endif +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB +#define CONFIG_PHY_VITESSE +#define CONFIG_PHY_REALTEK +#define CONFIG_PHYLIB_10G +#define RGMII_PHY1_ADDR 0x1 +#define RGMII_PHY2_ADDR 0x2 +#define SGMII_CARD_PORT1_PHY_ADDR 0x1C +#define SGMII_CARD_PORT2_PHY_ADDR 0x1D +#define SGMII_CARD_PORT3_PHY_ADDR 0x1E +#define SGMII_CARD_PORT4_PHY_ADDR 0x1F +/* PHY address on QSGMII riser card on slot 2 */ +#define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8 +#define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9 +#define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA +#define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB +#endif + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_SYS_FSL_PBL_PBI \ + board/freescale/ls1046aqds/ls1046aqds_pbi.cfg +#endif + +#ifdef CONFIG_NAND_BOOT +#define CONFIG_SYS_FSL_PBL_RCW \ + board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg +#endif + +#ifdef CONFIG_SD_BOOT +#ifdef CONFIG_SD_BOOT_QSPI +#define CONFIG_SYS_FSL_PBL_RCW \ + board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg +#else +#define CONFIG_SYS_FSL_PBL_RCW \ + board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg +#endif +#endif + +/* IFC */ +#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) +#define CONFIG_FSL_IFC +/* + * CONFIG_SYS_FLASH_BASE has the final address (core view) + * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) + * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address + * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting + */ +#define CONFIG_SYS_FLASH_BASE 0x60000000 +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 + +#ifndef CONFIG_SYS_NO_FLASH +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ +#endif +#endif + +/* SATA */ +#define CONFIG_LIBATA +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SCSI +#define CONFIG_DOS_PARTITION +#define CONFIG_BOARD_LATE_INIT + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +#define CONFIG_SYS_SATA AHCI_BASE_ADDR + +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + +/* + * IFC Definitions + */ +#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) +#define CONFIG_SYS_NOR0_CSPR_EXT (0x0) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR1_CSPR_EXT (0x0) +#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) + +#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ + CSOR_NOR_TRHZ_80) +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1a) | \ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0xe) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0 + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS, \ + CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} + +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +#define CONFIG_SYS_WRITE_SWAPPED_DATA + +/* + * NAND Flash Definitions + */ +#define CONFIG_NAND_FSL_IFC + +#define CONFIG_SYS_NAND_BASE 0x7e800000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE + +#define CONFIG_SYS_NAND_CSPR_EXT (0x0) + +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_NAND \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_8 /* 8-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \ + | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ + | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ + | CSOR_NAND_PB(64)) /* 64 Pages Per Block */ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x7) | \ + FTIM0_NAND_TWH(0xa)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0xe) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \ + FTIM2_NAND_TREH(0xa) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * 1024) +#endif + +#ifdef CONFIG_NAND_BOOT +#define CONFIG_SPL_PAD_TO 0x40000 /* block aligned */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SPL_PAD_TO +#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) +#endif + +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) +#define CONFIG_QIXIS_I2C_ACCESS +#define CONFIG_SYS_I2C_EARLY_INIT +#define CONFIG_SYS_NO_FLASH +#endif + +/* + * QIXIS Definitions + */ +#define CONFIG_FSL_QIXIS + +#ifdef CONFIG_FSL_QIXIS +#define QIXIS_BASE 0x7fb00000 +#define QIXIS_BASE_PHYS QIXIS_BASE +#define CONFIG_SYS_I2C_FPGA_ADDR 0x66 +#define QIXIS_LBMAP_SWITCH 6 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SHIFT 0 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x04 +#define QIXIS_LBMAP_NAND 0x09 +#define QIXIS_LBMAP_SD 0x00 +#define QIXIS_LBMAP_SD_QSPI 0xff +#define QIXIS_LBMAP_QSPI 0xff +#define QIXIS_RCW_SRC_NAND 0x110 +#define QIXIS_RCW_SRC_SD 0x040 +#define QIXIS_RCW_SRC_QSPI 0x045 +#define QIXIS_RST_CTL_RESET 0x41 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 + +#define CONFIG_SYS_FPGA_CSPR_EXT (0x0) +#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_MSEL_GPCM | \ + CSPR_V) +#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) +#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ + CSOR_NOR_NOR_MODE_AVD_NOR | \ + CSOR_NOR_TRHZ_80) + +/* + * QIXIS Timing parameters for IFC GPCM + */ +#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xc) | \ + FTIM0_GPCM_TEADC(0x20) | \ + FTIM0_GPCM_TEAHC(0x10)) +#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0x50) | \ + FTIM1_GPCM_TRAD(0x1f)) +#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0x8) | \ + FTIM2_GPCM_TCH(0x8) | \ + FTIM2_GPCM_TWP(0xf0)) +#define CONFIG_SYS_FPGA_FTIM3 0x0 +#endif + +#ifdef CONFIG_NAND_BOOT +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT +#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR +#define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK +#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR +#define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_FTIM0 +#define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_FTIM1 +#define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_FTIM2 +#define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT +#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR +#define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK +#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR +#define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_FTIM0 +#define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_FTIM1 +#define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_FTIM2 +#define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_FTIM3 +#endif + +/* + * I2C bus multiplexer + */ +#define I2C_MUX_PCA_ADDR_PRI 0x77 +#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */ +#define I2C_RETIMER_ADDR 0x18 +#define I2C_MUX_CH_DEFAULT 0x8 +#define I2C_MUX_CH_CH7301 0xC +#define I2C_MUX_CH5 0xD +#define I2C_MUX_CH6 0xE +#define I2C_MUX_CH7 0xF + +#define I2C_MUX_CH_VOL_MONITOR 0xa + +/* Voltage monitor on channel 2*/ +#define I2C_VOL_MONITOR_ADDR 0x40 +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 + +#define CONFIG_VID_FLS_ENV "ls1046aqds_vdd_mv" +#ifndef CONFIG_SPL_BUILD +#define CONFIG_VID +#endif +#define CONFIG_VOL_MONITOR_IR36021_SET +#define CONFIG_VOL_MONITOR_INA220 +/* The lowest and highest voltage allowed for LS1046AQDS */ +#define VDD_MV_MIN 819 +#define VDD_MV_MAX 1212 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END 0x9fffffff + +#define CONFIG_SYS_HZ 1000 + +/* + * Stack sizes + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (30 * 1024) + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +/* + * Environment + */ +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_NAND_BOOT +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SD_BOOT) +#define CONFIG_ENV_OFFSET (1024 * 1024) +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#elif defined(CONFIG_QSPI_BOOT) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000) +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_SIZE 0x20000 +#endif + +#define CONFIG_CMDLINE_TAG + +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) +#define CONFIG_BOOTCOMMAND "sf probe && sf read $kernel_load " \ + "e0000 f00000 && bootm $kernel_load" +#else +#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \ + "$kernel_size && bootm $kernel_load" +#endif + +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) +#define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:2m(uboot)," \ + "14m(free)" +#else +#define MTDPARTS_DEFAULT "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \ + "1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," \ + "1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," \ + "1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \ + "1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \ + "40m(nor_bank4_fit);7e800000.flash:" \ + "4m(nand_uboot),36m(nand_kernel)," \ + "472m(nand_free);spi0.0:2m(uboot)," \ + "14m(free)" +#endif + +#include <asm/fsl_secure_boot.h> + +#endif /* __LS1046AQDS_H__ */