Hi Daniel,
On 25.09.19 13:09, Daniel Schwierzeck wrote:
Am 25.09.19 um 11:45 schrieb Weijie Gao:
This patch series have the following changes:
- Add pinctrl(both pinmux and pinconf) driver, reset controller driver and clock driver for mt7628.
- Add mt7628 platform to mtk-sd driver.
- Modify mt7628's ethernet & usb phy driver to take advantages from the new drivers.
- Update mt7621-spi driver with a new transfer method.
- Enable fifo, disable flow control, and enable non-DM implementation for mtk hsuart driver.
- Enanble the new drivers for currently existed mt7628 boards.
Changes of v2:
- Change clock gateing driver to a more 'generic' driver which supports output clock rates of CPU/SYS_BUS/peripherals.
- mt7621-spi now uses accurate sys_freq from clock driver.
- Make PHY link detection optional via DT.
- Select essential drivers in Kconfig instead of setting in defconfig files.
Changes of v3:
- Add const qualifier for structs in pinctrl-mt7628.c.
- Make mt76x8-usb-phy depends on SOC_MT7628.
- Simplify logic of card-detection in mtk-sd.c.
from my side for the whole series:
Reviewed-by: Daniel Schwierzeck daniel.schwierzeck@gmail.com
it would be great if Stefan could give a Tested-by for the Gardena boards ;)
I'm just back from vacation and will try to review and test this patch series beginning (latest mid) of next week.
Thanks, Stefan
Weijie Gao (28): serial: serial_mtk: enable FIFO and disable flow control serial: serial_mtk: add non-DM version for SPL dts: mtmips: move uart property clock-frequency into mt7628an.dtsi dts: mtmips: enable high-speed UART support for mt7628 clk: add clock driver for MediaTek MT76x8 platform dts: mtmips: add clock node for mt7628 spi: mt7621-spi: use clock frequency from clk driver spi: mt7621-spi: remove data cache and rewrite its xfer function spi: mt7621-spi: restore default register value after each xfer pinctrl: add support for MediaTek MT7628 dts: mtmips: add pinctrl node for mt7628 dts: mtmips: add default pinctrl for uart nodes reset: add reset controller driver for MediaTek MIPS platform dts: mtmips: update reset controller node for mt7628 phy: mt76x8-usb-phy: add slew rate calibration and remove non-mt7628 part net: mt7628-eth: remove hardcoded gpio settings and regmap-based phy reset net: mt7628-eth: make phy link up detection optional via DT net: mt7628-eth: free rx descriptor on receiving failure net: mt7628-eth: add support to isolate LAN/WAN ports dts: mtmips: enable eth port0 led and link poll functions for all boards mmc: mtk-sd: add support for MediaTek MT7620/MT7628 SoCs mmc: mtk-sd: add a dts property cd-active-high for builtin-cd mode dts: mtmips: add mmc related nodes for mt7628an.dtsi dts: mtmips: add default pinctrl for gardena-smart-gateway-mt7688 dts: mtmips: add default pinctrl to eth nodes for all boards mips: mtmips: change baudrate table for all boards mips: mtmips: select essential drivers in Kconfig configs: mtmips: remove configs which are selected in Kconfig or useless
arch/mips/Kconfig | 6 + .../mips/dts/gardena-smart-gateway-mt7688.dts | 19 +- arch/mips/dts/linkit-smart-7688.dts | 16 +- arch/mips/dts/mt7628a.dtsi | 246 +++++++- arch/mips/mach-mtmips/Kconfig | 2 + ...gardena-smart-gateway-mt7688-ram_defconfig | 7 - .../gardena-smart-gateway-mt7688_defconfig | 7 - configs/linkit-smart-7688-ram_defconfig | 7 - configs/linkit-smart-7688_defconfig | 7 - drivers/clk/Makefile | 1 + drivers/clk/mtmips/Makefile | 3 + drivers/clk/mtmips/clk-mt7628.c | 158 +++++ drivers/mmc/Kconfig | 2 +- drivers/mmc/mtk-sd.c | 29 +- drivers/net/Kconfig | 1 + drivers/net/mt7628-eth.c | 135 ++-- drivers/phy/Kconfig | 1 + drivers/phy/mt76x8-usb-phy.c | 225 +++++-- drivers/pinctrl/Kconfig | 1 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/mtmips/Kconfig | 13 + drivers/pinctrl/mtmips/Makefile | 7 + drivers/pinctrl/mtmips/pinctrl-mt7628.c | 585 ++++++++++++++++++ .../pinctrl/mtmips/pinctrl-mtmips-common.c | 87 +++ .../pinctrl/mtmips/pinctrl-mtmips-common.h | 53 ++ drivers/reset/Kconfig | 7 + drivers/reset/Makefile | 1 + drivers/reset/reset-mtmips.c | 82 +++ drivers/serial/serial.c | 2 + drivers/serial/serial_mtk.c | 223 ++++++- drivers/spi/mt7621_spi.c | 247 ++++---- .../configs/gardena-smart-gateway-mt7688.h | 2 +- include/configs/linkit-smart-7688.h | 2 +- include/dt-bindings/clock/mt7628-clk.h | 37 ++ include/dt-bindings/reset/mt7628-reset.h | 36 ++ 35 files changed, 1929 insertions(+), 329 deletions(-) create mode 100644 drivers/clk/mtmips/Makefile create mode 100644 drivers/clk/mtmips/clk-mt7628.c create mode 100644 drivers/pinctrl/mtmips/Kconfig create mode 100644 drivers/pinctrl/mtmips/Makefile create mode 100644 drivers/pinctrl/mtmips/pinctrl-mt7628.c create mode 100644 drivers/pinctrl/mtmips/pinctrl-mtmips-common.c create mode 100644 drivers/pinctrl/mtmips/pinctrl-mtmips-common.h create mode 100644 drivers/reset/reset-mtmips.c create mode 100644 include/dt-bindings/clock/mt7628-clk.h create mode 100644 include/dt-bindings/reset/mt7628-reset.h
Viele Grüße, Stefan