Import PM8994 and PMI8994 DTSI files in preparation for switching MSM8996 boards to upstream DTS.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong neil.armstrong@linaro.org Signed-off-by: Caleb Connolly caleb.connolly@linaro.org --- arch/arm/dts/pm8994.dtsi | 152 ++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/dts/pmi8994.dtsi | 65 ++++++++++++++++++++ 2 files changed, 217 insertions(+)
diff --git a/arch/arm/dts/pm8994.dtsi b/arch/arm/dts/pm8994.dtsi new file mode 100644 index 000000000000..d44a95caf04a --- /dev/null +++ b/arch/arm/dts/pm8994.dtsi @@ -0,0 +1,152 @@ +// SPDX-License-Identifier: GPL-2.0 +#include <dt-bindings/iio/qcom,spmi-vadc.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +/ { + thermal-zones { + pm8994-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&pm8994_temp>; + + trips { + pm8994_alert0: pm8994-alert0 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + pm8994_crit: pm8994-crit { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; +}; + +&spmi_bus { + + pmic@0 { + compatible = "qcom,pm8994", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@6000 { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>, <0x6100>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; + }; + + pm8994_pon: pon@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x800>; + mode-bootloader = <0x2>; + mode-recovery = <0x1>; + + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + }; + + pm8994_resin: resin { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + status = "disabled"; + }; + }; + + pm8994_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; + io-channels = <&pm8994_vadc VADC_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pm8994_vadc: adc@3100 { + compatible = "qcom,spmi-vadc"; + reg = <0x3100>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + + channel@7 { + reg = <VADC_VSYS>; + qcom,pre-scaling = <1 3>; + label = "vph_pwr"; + }; + channel@8 { + reg = <VADC_DIE_TEMP>; + label = "die_temp"; + }; + channel@9 { + reg = <VADC_REF_625MV>; + label = "ref_625mv"; + }; + channel@a { + reg = <VADC_REF_1250MV>; + label = "ref_1250mv"; + }; + channel@e { + reg = <VADC_GND_REF>; + }; + channel@f { + reg = <VADC_VDD_VADC>; + }; + }; + + pm8994_gpios: gpio@c000 { + compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio"; + reg = <0xc000>; + gpio-controller; + gpio-ranges = <&pm8994_gpios 0 0 22>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pm8994_mpps: mpps@a000 { + compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp"; + reg = <0xa000>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pm8994_mpps 0 0 8>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@1 { + compatible = "qcom,pm8994", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8994_lpg: pwm { + compatible = "qcom,pm8994-lpg"; + + #address-cells = <1>; + #size-cells = <0>; + #pwm-cells = <2>; + + status = "disabled"; + }; + + pm8994_spmi_regulators: regulators { + compatible = "qcom,pm8994-regulators"; + }; + }; +}; diff --git a/arch/arm/dts/pmi8994.dtsi b/arch/arm/dts/pmi8994.dtsi new file mode 100644 index 000000000000..36d6a1fb553a --- /dev/null +++ b/arch/arm/dts/pmi8994.dtsi @@ -0,0 +1,65 @@ +// SPDX-License-Identifier: GPL-2.0 +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + + pmic@2 { + compatible = "qcom,pmi8994", "qcom,spmi-pmic"; + reg = <0x2 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmi8994_gpios: gpio@c000 { + compatible = "qcom,pmi8994-gpio", "qcom,spmi-gpio"; + reg = <0xc000>; + gpio-controller; + gpio-ranges = <&pmi8994_gpios 0 0 10>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pmi8994_mpps: mpps@a000 { + compatible = "qcom,pmi8994-mpp", "qcom,spmi-mpp"; + reg = <0xa000>; + gpio-controller; + gpio-ranges = <&pmi8994_mpps 0 0 4>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@3 { + compatible = "qcom,pmi8994", "qcom,spmi-pmic"; + reg = <0x3 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmi8994_lpg: pwm { + compatible = "qcom,pmi8994-lpg"; + + #address-cells = <1>; + #size-cells = <0>; + #pwm-cells = <2>; + + status = "disabled"; + }; + + pmi8994_spmi_regulators: regulators { + compatible = "qcom,pmi8994-regulators"; + }; + + pmi8994_wled: wled@d800 { + compatible = "qcom,pmi8994-wled"; + reg = <0xd800>, <0xd900>; + interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, + <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "ovp", "short"; + qcom,cabc; + qcom,external-pfet; + status = "disabled"; + }; + }; +};