On 2016/11/16 17:31, Michal Simek wrote:
On 16.11.2016 10:22, Dongpo Li wrote:
On 2016/11/16 16:24, Michal Simek wrote:
It is confusing that mdio commands work and report phy id as decimal value when mii is working with hex values.
For example: ZynqMP> mdio list gem: 21 - TI DP83867 <--> ethernet@ff0e0000 ZynqMP> mdio read ethernet@ff0e0000 0 Reading from bus gem PHY at address 21: 0 - 0x1140 ZynqMP> mii dump 21 0 Incorrect PHY address. Range should be 0-31 ... ZynqMP> mii dump 15 0. (1140) -- PHY control register -- (8000:0000) 0.15 = 0 reset
U-Boot normally takes hex values that's why this patch is changing mdio command to handle hex instead of changing mii command to handle decimal values.
Signed-off-by: Michal Simek michal.simek@xilinx.com
cmd/mdio.c | 6 +++--- common/miiphyutil.c | 2 +- drivers/net/zynq_gem.c | 2 +- 3 files changed, 5 insertions(+), 5 deletions(-)
diff --git a/cmd/mdio.c b/cmd/mdio.c index fb13d050752a..21dc103736e7 100644 --- a/cmd/mdio.c +++ b/cmd/mdio.c @@ -27,12 +27,12 @@ static uint last_reg_hi; static int extract_range(char *input, int *plo, int *phi) { char *end;
- *plo = simple_strtol(input, &end, 0);
- *plo = simple_strtol(input, &end, 16);
Hi, the last parameter 0 of function simple_strtol should mean it can recognize the integer automatic as hex value if the data is beginning with 0x, as octet value if beginning with 0, else decimal value. So this code has no problem. I checked the implementation of function simple_strtol and found the following code: if (!base) base = 10; So I think we should fix the implementation of simple_strtol.
yes. I have checked that implementation too. But the question is if this is aligned with others U-Boot parameters. It is confusing that with one command uses 21 as dec, another 15 or 0x15.
That's why will be worth to synchronize this.
md is one example where all is taken as hex.
ZynqMP> md 15 10 00000015: 00000000 00000000 01000000 00000000 ................ 00000025: 00000000 00000000 00000000 00000000 ................ 00000035: 00000000 00000000 00000000 00000000 ................ 00000045: 00000000 00000000 00000000 00000000 ................ ZynqMP> md f 10 0000000f: fe5000ff 000000ff 00000000 00000000 ..P............. 0000001f: 00000100 00000000 00000000 00000000 ................ 0000002f: 00000000 00000000 00000000 00000000 ................ 0000003f: 00000000 00000000 00000000 00000000 ................ ZynqMP> md 0xf 10 0000000f: fe5000ff 000000ff 00000000 00000000 ..P............. 0000001f: 00000100 00000000 00000000 00000000 ................ 0000002f: 00000000 00000000 00000000 00000000 ................ 0000003f: 00000000 00000000 00000000 00000000 ................
I checked the md command, the code is: addr = simple_strtoul(argv[1], NULL, 16); length = simple_strtoul(argv[2], NULL, 16); That's to say, you must consider the input addr and length as hex value if you want to use the md command.