Hi Kumar, I am using 2009-06 u-boot for MPC8640D based custom board. I just want to know whether the second core of MPC8640D is kicked off automatically or will it required by the user to kick[like mpc85xx/mp.c]. Also if am enabling the CONFIG_MP macro and CONFIG_NUM_CPUS as 2, then the reset command of the target is not working(means board is getting hanged). I have mentioned the value of CONFIG_SYS_SCRATCH_VA as 0xf5000000.
Also when i try to boot linux using this configuration i was getting into kernel panic.
## Current stack ends at 0x3fa91a08 ## Booting kernel from Legacy Image at 00400000 ... Image Name: Linux-2.6.30-dpvpx0689 Created: 2009-12-01 4:45:09 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2307361 Bytes = 2.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 04000000 Booting using the fdt blob at 0x4000000 Uncompressing Kernel Image ... OK Loading Device Tree to 007fa000, end 007ff150 ... OK ## Transferring control to Linux (at address 00000000) ... Booting using OF flat tree... Using DPVPX0689 machine description Total memory = 1024MB; using 2048kB for hash table (at afe00000) Linux version 2.6.30-dpvpx0689 (root@localhost.localdomain) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #70 SMP Tue Dec 1 10:14:07 IST 2009 Found legacy serial port 0 for /soc@f6000000/serial@4500 mem=f6004500, taddr=f6004500, irq=0, clk=400000000, speed=0 Found legacy serial port 1 for /soc@f6000000/serial@4600 mem=f6004600, taddr=f6004600, irq=0, clk=400000000, speed=0 CPU maps initialized for 1 thread per core (thread shift is 0) console [udbg0] enabled setup_arch: bootmem dpvpx0689_setup_arch() Found FSL PCI host bridge at 0x00000000f6008000. Firmware bus number: 0->15 PCI host bridge /pcie@f6008000 ranges: MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000 IO 0x00000000f8000000..0x00000000fbffffff -> 0x0000000000000000 Single Board Computers from Data Patterns Ported & Developed By COTS DIVISION arch: exit Top of RAM: 0x40000000, Total RAM: 0x40000000 Memory hole size: 0MB Zone PFN ranges: DMA 0x00000000 -> 0x00030000 Normal 0x00030000 -> 0x00030000 HighMem 0x00030000 -> 0x00040000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00040000 On node 0 totalpages: 262144 free_area_init_node: node 0, pgdat a047d1c0, node_mem_map a07fd000 DMA zone: 1536 pages used for memmap DMA zone: 0 pages reserved DMA zone: 195072 pages, LIFO batch:31 HighMem zone: 512 pages used for memmap HighMem zone: 65024 pages, LIFO batch:15 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 Kernel command line: root=/dev/nfs rw nfsroot=10.5.18.3:/ppc/netfs/fc5fs/ ip=10.5.18.230:10.5.18.3:10.5.18.3:255.0.0.0:DPVPX0689:eth0:off console=ttyS0,115200 NR_IRQS:512 mpic: Setting up MPIC " MPIC " version 1.2 at f6040000, max 2 CPUs mpic: ISU size: 256, shift: 8, mask: ff mpic: Initializing for 256 sources PID hash table entries: 4096 (order: 12, 16384 bytes) time_init: decrementer frequency = 100.000000 MHz time_init: processor frequency = 800.000000 MHz clocksource: timebase mult[2800000] shift[22] registered clockevent: decrementer mult[1999] shift[16] cpu[0] Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) High memory: 262140k Memory: 1031504k/1048576k available (4444k kernel code, 16252k reserved, 160k data, 169k bss, 200k init) Kernel virtual memory layout: * 0xfffe0000..0xfffff000 : fixmap * 0xff800000..0xffc00000 : highmem PTEs * 0xfe7ed000..0xff800000 : early ioremap * 0xd1000000..0xfe7ed000 : vmalloc & ioremap Calibrating delay loop... 199.68 BogoMIPS (lpj=99840) Mount-cache hash table entries: 512 mpic: requesting IPIs ... Processor 1 found. clockevent: decrementer mult[1999] shift[16] cpu[1] Brought up 2 CPUs Unable to handle kernel paging request for data at address 0x00000004 Faulting instruction address: 0xa0023e10 Oops: Kernel access of bad area, sig: 11 [#1] SMP NR_CPUS=2 DPVPX0689 Modules linked in: NIP: a0023e10 LR: a0023dd0 CTR: 00000000 REGS: cf841e90 TRAP: 0300 Not tainted (2.6.30-dpvpx0689) MSR: 00009032 <EE,ME,IR,DR> CR: 24004028 XER: 20000000 DAR: 00000004, DSISR: 40000000 TASK = cf83f930[1] 'swapper' THREAD: cf840000 CPU: 0 GPR00: 00000000 cf841f40 cf83f930 00000000 00000000 00000000 cf841f50 00000000 GPR08: 00000000 00000000 00000002 a10018f4 22004082 ffffffff 3fee6c00 3ff94000 GPR16: ffffffbf ffbf7bff 00000000 00000000 00000000 cf83a800 a10018e8 a0491224 GPR24: a0490000 a04558f8 00000000 cf801f20 a1006070 a10018e8 a10018f8 00000000 NIP [a0023e10] __build_sched_domains+0x354/0x464 LR [a0023dd0] __build_sched_domains+0x314/0x464 Call Trace: [cf841f40] [a0023b98] __build_sched_domains+0xdc/0x464 (unreliable) [cf841f90] [a04326ec] sched_init_smp+0x88/0x1e8 [cf841fc0] [a0425a40] kernel_init+0x148/0x1f0 [cf841ff0] [a00131f8] kernel_thread+0x4c/0x68 Instruction dump: 813e0008 2f9c0000 90090004 419e00d4 801e0034 70090100 40820010 801c0034 70090280 408200bc 83fc0008 83be0008 <807f0004> 801d0004 7c630214 907d0004 ---[ end trace 31fd0ba7d8756001 ]--- Kernel panic - not syncing: Attempted to kill init! Rebooting in 180 seconds.. Kindly suggest me what might be the error.
Thank you, T.