On 12 June 2017 at 03:59, Wadim Egorov w.egorov@phytec.de wrote:
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC. The module can be connected to different carrier boards. It can be also equipped with different RAM, SPI flash and eMMC variants. The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development board made by PHYTEC. This board works in a combination with the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov w.egorov@phytec.de
Changes in v3:
Added u-boot,dm-pre-reloc to regulators subnode (PMIC failed to bind because of the missing regulators node)
Removed the hacky PMIC setup from phycore_init
Use CONFIG_TARGET_PHYCORE_RK3288 to cover board-specific stuff
Things get ugly when I use of_machine_is_compatible(). Boards whith CONFIG_SPL_OF_PLATDATA disabled would compile in of_machine_is_compatible() which checks for my board. phycore_init() calls rk818_spl_configure_*() which depends on CONFIG_SPL_POWER_SUPPORT. So this will cause undefined reference linker warnings for every other rockchip board. That's the reason why I moved back to CONFIG_TARGET_PHYCORE_RK3288.
arch/arm/dts/Makefile | 1 + arch/arm/dts/rk3288-phycore-rdk.dts | 294 ++++++++++++++++ arch/arm/dts/rk3288-phycore-som.dtsi | 506 +++++++++++++++++++++++++++ arch/arm/mach-rockchip/rk3288-board-spl.c | 35 ++ arch/arm/mach-rockchip/rk3288/Kconfig | 10 + board/phytec/phycore_rk3288/Kconfig | 15 + board/phytec/phycore_rk3288/MAINTAINERS | 6 + board/phytec/phycore_rk3288/Makefile | 8 + board/phytec/phycore_rk3288/phycore-rk3288.c | 8 + configs/phycore-rk3288_defconfig | 70 ++++ include/configs/phycore_rk3288.h | 23 ++ 11 files changed, 976 insertions(+) create mode 100644 arch/arm/dts/rk3288-phycore-rdk.dts create mode 100644 arch/arm/dts/rk3288-phycore-som.dtsi create mode 100644 board/phytec/phycore_rk3288/Kconfig create mode 100644 board/phytec/phycore_rk3288/MAINTAINERS create mode 100644 board/phytec/phycore_rk3288/Makefile create mode 100644 board/phytec/phycore_rk3288/phycore-rk3288.c create mode 100644 configs/phycore-rk3288_defconfig create mode 100644 include/configs/phycore_rk3288.h
Reviewed-by: Simon Glass sjg@chromium.org
(assuming we need to set up the battery / charger in SPL)
But can you please check the compatible string to decide whether you need to do the phytec stuff, instead of an #ifdef on the target? I suppose if it increase code size it is OK to have both, but the #ifdef should be a size optimisation, not the main method of selecting the code Is there a way to describe what is needed in the DT?