Add ethernet support for Compulab CM-FX6 CoM
Cc: Igor Grinberg grinberg@compulab.co.il Cc: Stefano Babic sbabic@denx.de Cc: Tom Rini trini@ti.com Signed-off-by: Nikita Kiryanov nikita@compulab.co.il --- board/compulab/cm_fx6/cm_fx6.c | 100 +++++++++++++++++++++++++++++++++++++++++ board/compulab/cm_fx6/common.h | 1 + include/configs/cm_fx6.h | 16 ++++++- 3 files changed, 115 insertions(+), 2 deletions(-)
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c index 6d37c21..d074af4 100644 --- a/board/compulab/cm_fx6/cm_fx6.c +++ b/board/compulab/cm_fx6/cm_fx6.c @@ -9,13 +9,100 @@ */
#include <common.h> +#include <miiphy.h> +#include <netdev.h> +#include <fdt_support.h> #include <asm/arch/crm_regs.h> #include <asm/arch/sys_proto.h> #include <asm/io.h> +#include <asm/gpio.h> #include "common.h"
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_FEC_MXC +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +static int mx6_rgmii_rework(struct phy_device *phydev) +{ + unsigned short val; + + /* Ar8031 phy SmartEEE feature cause link status generates glitch, + * which cause ethernet link down/up issue, so disable SmartEEE + */ + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x3); + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d); + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003); + val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); + val &= ~(0x1 << 8); + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val); + + /* To enable AR8031 ouput a 125MHz clk from CLK_25M */ + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); + + val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); + val &= 0xffe3; + val |= 0x18; + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val); + + /* introduce tx clock delay */ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5); + val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); + val |= 0x0100; + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val); + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + mx6_rgmii_rework(phydev); + + if (phydev->drv->config) + return phydev->drv->config(phydev); + + return 0; +} + +static iomux_v3_cfg_t const enet_pads[] = { + IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_GPIO_0__CCM_CLKO1 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(0x84)), + IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | + MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | + MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | + MUX_PAD_CTRL(ENET_PAD_CTRL)), +}; + +int board_eth_init(bd_t *bis) +{ + SETUP_IOMUX_PADS(enet_pads); + /* phy reset */ + gpio_direction_output(CM_FX6_ENET_NRST, 0); + udelay(500); + gpio_set_value(CM_FX6_ENET_NRST, 1); + enable_enet_clk(1); + return cpu_eth_init(bis); +} +#endif + #ifdef CONFIG_NAND_MXS static iomux_v3_cfg_t const nand_pads[] = { IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL)), @@ -66,6 +153,19 @@ int board_mmc_init(bd_t *bis) } #endif
+#ifdef CONFIG_OF_BOARD_SETUP +void ft_board_setup(void *blob, bd_t *bd) +{ + uint8_t enetaddr[6]; + + /* MAC addr */ + if (eth_getenv_enetaddr("ethaddr", enetaddr)) { + fdt_find_and_setprop(blob, "/fec", "local-mac-address", + enetaddr, 6, 1); + } +} +#endif + int board_init(void) { gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; diff --git a/board/compulab/cm_fx6/common.h b/board/compulab/cm_fx6/common.h index 05eab34..94ff39e 100644 --- a/board/compulab/cm_fx6/common.h +++ b/board/compulab/cm_fx6/common.h @@ -15,6 +15,7 @@
#define CM_FX6_ECSPI_BUS0_CS0 IMX_GPIO_NR(2, 30) #define CM_FX6_GREEN_LED IMX_GPIO_NR(2, 31) +#define CM_FX6_ENET_NRST IMX_GPIO_NR(2, 8)
#if defined(CONFIG_FSL_ESDHC) #include <fsl_esdhc.h> diff --git a/include/configs/cm_fx6.h b/include/configs/cm_fx6.h index 973150f..1923214 100644 --- a/include/configs/cm_fx6.h +++ b/include/configs/cm_fx6.h @@ -39,8 +39,6 @@ #undef CONFIG_CMD_XIMG #undef CONFIG_CMD_FPGA #undef CONFIG_CMD_IMLS -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS
/* MMC */ #define CONFIG_MMC @@ -193,6 +191,19 @@ #define CONFIG_APBH_DMA_BURST8 #endif
+/* Ethernet */ +#define CONFIG_FEC_MXC +#define CONFIG_FEC_MXC_PHYADDR 0 +#define CONFIG_FEC_XCV_TYPE RGMII +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_PHYLIB +#define CONFIG_PHY_ATHEROS +#define CONFIG_MII +#define CONFIG_ETHPRIME "FEC0" +#define CONFIG_ARP_TIMEOUT 200UL +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_NET_RETRY_COUNT 5 + /* GPIO */ #define CONFIG_MXC_GPIO
@@ -211,6 +222,7 @@ #define CONFIG_STACKSIZE (128 * 1024) #define CONFIG_SYS_MALLOC_LEN (2 * 1024 * 1024) #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */ +#define CONFIG_OF_BOARD_SETUP
/* SPL */ #define CONFIG_SPL