- Driver not used by any boards - No update on 'dm conversion'
Signed-off-by: Jagan Teki jagan@amarulasolutions.com --- drivers/spi/Kconfig | 6 - drivers/spi/Makefile | 1 - drivers/spi/mpc8xx_spi.c | 336 ----------------------------------------------- 3 files changed, 343 deletions(-) delete mode 100644 drivers/spi/mpc8xx_spi.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 235a8c7d73..fd3f115ccf 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -274,12 +274,6 @@ config LPC32XX_SSP help Enable support for SPI on LPC32xx
-config MPC8XX_SPI - bool "MPC8XX SPI Driver" - depends on 8xx - help - Enable support for SPI on MPC8XX - config MPC8XXX_SPI bool "MPC8XXX SPI Driver" help diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 4b6000fd9a..f104836630 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -31,7 +31,6 @@ obj-$(CONFIG_FSL_QSPI) += fsl_qspi.o obj-$(CONFIG_ICH_SPI) += ich.o obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o -obj-$(CONFIG_MPC8XX_SPI) += mpc8xx_spi.o obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o obj-$(CONFIG_MVEBU_A3700_SPI) += mvebu_a3700_spi.o obj-$(CONFIG_MXC_SPI) += mxc_spi.o diff --git a/drivers/spi/mpc8xx_spi.c b/drivers/spi/mpc8xx_spi.c deleted file mode 100644 index b5bd558526..0000000000 --- a/drivers/spi/mpc8xx_spi.c +++ /dev/null @@ -1,336 +0,0 @@ -/* - * Copyright (c) 2001 Navin Boppuri / Prashant Patel - * nboppuri@trinetcommunication.com, - * pmpatel@trinetcommunication.com - * Copyright (c) 2001 Gerd Mennchen Gerd.Mennchen@icn.siemens.de - * Copyright (c) 2001 Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * MPC8xx CPM SPI interface. - * - * Parts of this code are probably not portable and/or specific to - * the board which I used for the tests. Please send fixes/complaints - * to wd@denx.de - * - */ - -#include <common.h> -#include <mpc8xx.h> -#include <commproc.h> -#include <linux/ctype.h> -#include <malloc.h> -#include <post.h> -#include <serial.h> - -#define SPI_EEPROM_WREN 0x06 -#define SPI_EEPROM_RDSR 0x05 -#define SPI_EEPROM_READ 0x03 -#define SPI_EEPROM_WRITE 0x02 - -/* --------------------------------------------------------------- - * Offset for initial SPI buffers in DPRAM: - * We need a 520 byte scratch DPRAM area to use at an early stage. - * It is used between the two initialization calls (spi_init_f() - * and spi_init_r()). - * The value 0xb00 makes it far enough from the start of the data - * area (as well as from the stack pointer). - * --------------------------------------------------------------- */ -#ifndef CONFIG_SYS_SPI_INIT_OFFSET -#define CONFIG_SYS_SPI_INIT_OFFSET 0xB00 -#endif - -#define CPM_SPI_BASE_RX CPM_SPI_BASE -#define CPM_SPI_BASE_TX (CPM_SPI_BASE + sizeof(cbd_t)) - -/* ------------------- - * Function prototypes - * ------------------- */ -ssize_t spi_xfer(size_t); - -/* ------------------- - * Variables - * ------------------- */ - -#define MAX_BUFFER 0x104 - -/* ---------------------------------------------------------------------- - * Initially we place the RX and TX buffers at a fixed location in DPRAM! - * ---------------------------------------------------------------------- */ -static uchar *rxbuf = - (uchar *)&((cpm8xx_t *)&((immap_t *)CONFIG_SYS_IMMR)->im_cpm)->cp_dpmem - [CONFIG_SYS_SPI_INIT_OFFSET]; -static uchar *txbuf = - (uchar *)&((cpm8xx_t *)&((immap_t *)CONFIG_SYS_IMMR)->im_cpm)->cp_dpmem - [CONFIG_SYS_SPI_INIT_OFFSET+MAX_BUFFER]; - -/* ************************************************************************** - * - * Function: spi_init_f - * - * Description: Init SPI-Controller (ROM part) - * - * return: --- - * - * *********************************************************************** */ -void spi_init_f(void) -{ - immap_t __iomem *immr = (immap_t __iomem *)CONFIG_SYS_IMMR; - cpm8xx_t __iomem *cp = &immr->im_cpm; - spi_t __iomem *spi = (spi_t __iomem *)&cp->cp_dparam[PROFF_SPI]; - cbd_t __iomem *tbdf, *rbdf; - - /* Disable relocation */ - out_be16(&spi->spi_rpbase, 0); - -/* 1 */ - /* ------------------------------------------------ - * Initialize Port B SPI pins -> page 34-8 MPC860UM - * (we are only in Master Mode !) - * ------------------------------------------------ */ - - /* -------------------------------------------- - * GPIO or per. Function - * PBPAR[28] = 1 [0x00000008] -> PERI: (SPIMISO) - * PBPAR[29] = 1 [0x00000004] -> PERI: (SPIMOSI) - * PBPAR[30] = 1 [0x00000002] -> PERI: (SPICLK) - * PBPAR[31] = 0 [0x00000001] -> GPIO: (CS for PCUE/CCM-EEPROM) - * -------------------------------------------- */ - clrsetbits_be32(&cp->cp_pbpar, 0x00000001, 0x0000000E); /* set bits */ - - /* ---------------------------------------------- - * In/Out or per. Function 0/1 - * PBDIR[28] = 1 [0x00000008] -> PERI1: SPIMISO - * PBDIR[29] = 1 [0x00000004] -> PERI1: SPIMOSI - * PBDIR[30] = 1 [0x00000002] -> PERI1: SPICLK - * PBDIR[31] = 1 [0x00000001] -> GPIO OUT: CS for PCUE/CCM-EEPROM - * ---------------------------------------------- */ - setbits_be32(&cp->cp_pbdir, 0x0000000F); - - /* ---------------------------------------------- - * open drain or active output - * PBODR[28] = 1 [0x00000008] -> open drain: SPIMISO - * PBODR[29] = 0 [0x00000004] -> active output SPIMOSI - * PBODR[30] = 0 [0x00000002] -> active output: SPICLK - * PBODR[31] = 0 [0x00000001] -> active output GPIO OUT: CS for PCUE/CCM - * ---------------------------------------------- */ - - clrsetbits_be16(&cp->cp_pbodr, 0x00000007, 0x00000008); - - /* Initialize the parameter ram. - * We need to make sure many things are initialized to zero - */ - out_be32(&spi->spi_rstate, 0); - out_be32(&spi->spi_rdp, 0); - out_be16(&spi->spi_rbptr, 0); - out_be16(&spi->spi_rbc, 0); - out_be32(&spi->spi_rxtmp, 0); - out_be32(&spi->spi_tstate, 0); - out_be32(&spi->spi_tdp, 0); - out_be16(&spi->spi_tbptr, 0); - out_be16(&spi->spi_tbc, 0); - out_be32(&spi->spi_txtmp, 0); - -/* 3 */ - /* Set up the SPI parameters in the parameter ram */ - out_be16(&spi->spi_rbase, CPM_SPI_BASE_RX); - out_be16(&spi->spi_tbase, CPM_SPI_BASE_TX); - - /***********IMPORTANT******************/ - - /* - * Setting transmit and receive buffer descriptor pointers - * initially to rbase and tbase. Only the microcode patches - * documentation talks about initializing this pointer. This - * is missing from the sample I2C driver. If you dont - * initialize these pointers, the kernel hangs. - */ - out_be16(&spi->spi_rbptr, CPM_SPI_BASE_RX); - out_be16(&spi->spi_tbptr, CPM_SPI_BASE_TX); - -/* 4 */ - /* Init SPI Tx + Rx Parameters */ - while (in_be16(&cp->cp_cpcr) & CPM_CR_FLG) - ; - - out_be16(&cp->cp_cpcr, mk_cr_cmd(CPM_CR_CH_SPI, CPM_CR_INIT_TRX) | - CPM_CR_FLG); - while (in_be16(&cp->cp_cpcr) & CPM_CR_FLG) - ; - -/* 5 */ - /* Set SDMA configuration register */ - out_be32(&immr->im_siu_conf.sc_sdcr, 0x0001); - -/* 6 */ - /* Set to big endian. */ - out_8(&spi->spi_tfcr, SMC_EB); - out_8(&spi->spi_rfcr, SMC_EB); - -/* 7 */ - /* Set maximum receive size. */ - out_be16(&spi->spi_mrblr, MAX_BUFFER); - -/* 8 + 9 */ - /* tx and rx buffer descriptors */ - tbdf = (cbd_t __iomem *)&cp->cp_dpmem[CPM_SPI_BASE_TX]; - rbdf = (cbd_t __iomem *)&cp->cp_dpmem[CPM_SPI_BASE_RX]; - - clrbits_be16(&tbdf->cbd_sc, BD_SC_READY); - clrbits_be16(&rbdf->cbd_sc, BD_SC_EMPTY); - - /* Set the bd's rx and tx buffer address pointers */ - out_be32(&rbdf->cbd_bufaddr, (ulong)rxbuf); - out_be32(&tbdf->cbd_bufaddr, (ulong)txbuf); - -/* 10 + 11 */ - out_8(&cp->cp_spim, 0); /* Mask all SPI events */ - out_8(&cp->cp_spie, SPI_EMASK); /* Clear all SPI events */ - - return; -} - -/* ************************************************************************** - * - * Function: spi_init_r - * - * Description: Init SPI-Controller (RAM part) - - * The malloc engine is ready and we can move our buffers to - * normal RAM - * - * return: --- - * - * *********************************************************************** */ -void spi_init_r(void) -{ - immap_t __iomem *immr = (immap_t __iomem *)CONFIG_SYS_IMMR; - cpm8xx_t __iomem *cp = &immr->im_cpm; - spi_t __iomem *spi = (spi_t __iomem *)&cp->cp_dparam[PROFF_SPI]; - cbd_t __iomem *tbdf, *rbdf; - - /* Disable relocation */ - out_be16(&spi->spi_rpbase, 0); - - /* tx and rx buffer descriptors */ - tbdf = (cbd_t __iomem *)&cp->cp_dpmem[CPM_SPI_BASE_TX]; - rbdf = (cbd_t __iomem *)&cp->cp_dpmem[CPM_SPI_BASE_RX]; - - /* Allocate memory for RX and TX buffers */ - rxbuf = (uchar *)malloc(MAX_BUFFER); - txbuf = (uchar *)malloc(MAX_BUFFER); - - out_be32(&rbdf->cbd_bufaddr, (ulong)rxbuf); - out_be32(&tbdf->cbd_bufaddr, (ulong)txbuf); - - return; -} - -/**************************************************************************** - * Function: spi_write - **************************************************************************** */ -ssize_t spi_write(uchar *addr, int alen, uchar *buffer, int len) -{ - int i; - - memset(rxbuf, 0, MAX_BUFFER); - memset(txbuf, 0, MAX_BUFFER); - *txbuf = SPI_EEPROM_WREN; /* write enable */ - spi_xfer(1); - memcpy(txbuf, addr, alen); - *txbuf = SPI_EEPROM_WRITE; /* WRITE memory array */ - memcpy(alen + txbuf, buffer, len); - spi_xfer(alen + len); - /* ignore received data */ - for (i = 0; i < 1000; i++) { - *txbuf = SPI_EEPROM_RDSR; /* read status */ - txbuf[1] = 0; - spi_xfer(2); - if (!(rxbuf[1] & 1)) - break; - udelay(1000); - } - if (i >= 1000) - printf("*** spi_write: Time out while writing!\n"); - - return len; -} - -/**************************************************************************** - * Function: spi_read - **************************************************************************** */ -ssize_t spi_read(uchar *addr, int alen, uchar *buffer, int len) -{ - memset(rxbuf, 0, MAX_BUFFER); - memset(txbuf, 0, MAX_BUFFER); - memcpy(txbuf, addr, alen); - *txbuf = SPI_EEPROM_READ; /* READ memory array */ - - /* - * There is a bug in 860T (?) that cuts the last byte of input - * if we're reading into DPRAM. The solution we choose here is - * to always read len+1 bytes (we have one extra byte at the - * end of the buffer). - */ - spi_xfer(alen + len + 1); - memcpy(buffer, alen + rxbuf, len); - - return len; -} - -/**************************************************************************** - * Function: spi_xfer - **************************************************************************** */ -ssize_t spi_xfer(size_t count) -{ - immap_t __iomem *immr = (immap_t __iomem *)CONFIG_SYS_IMMR; - cpm8xx_t __iomem *cp = &immr->im_cpm; - spi_t __iomem *spi = (spi_t __iomem *)&cp->cp_dparam[PROFF_SPI]; - cbd_t __iomem *tbdf, *rbdf; - int tm; - - /* Disable relocation */ - out_be16(&spi->spi_rpbase, 0); - - tbdf = (cbd_t __iomem *)&cp->cp_dpmem[CPM_SPI_BASE_TX]; - rbdf = (cbd_t __iomem *)&cp->cp_dpmem[CPM_SPI_BASE_RX]; - - /* Set CS for device */ - clrbits_be32(&cp->cp_pbdat, 0x0001); - - /* Setting tx bd status and data length */ - out_be16(&tbdf->cbd_sc, BD_SC_READY | BD_SC_LAST | BD_SC_WRAP); - out_be16(&tbdf->cbd_datlen, count); - - /* Setting rx bd status and data length */ - out_be16(&rbdf->cbd_sc, BD_SC_EMPTY | BD_SC_WRAP); - out_be16(&rbdf->cbd_datlen, 0); /* rx length has no significance */ - - clrsetbits_be16(&cp->cp_spmode, ~SPMODE_LOOP, SPMODE_REV | SPMODE_MSTR | - SPMODE_EN | SPMODE_LEN(8) | SPMODE_PM(0x8)); - out_8(&cp->cp_spim, 0); /* Mask all SPI events */ - out_8(&cp->cp_spie, SPI_EMASK); /* Clear all SPI events */ - - /* start spi transfer */ - setbits_8(&cp->cp_spcom, SPI_STR); /* Start transmit */ - - /* -------------------------------- - * Wait for SPI transmit to get out - * or time out (1 second = 1000 ms) - * -------------------------------- */ - for (tm = 0; tm < 1000; ++tm) { - if (in_8(&cp->cp_spie) & SPI_TXB) /* Tx Buffer Empty */ - break; - if ((in_be16(&tbdf->cbd_sc) & BD_SC_READY) == 0) - break; - udelay(1000); - } - if (tm >= 1000) - printf("*** spi_xfer: Time out while xferring to/from SPI!\n"); - - /* Clear CS for device */ - setbits_be32(&cp->cp_pbdat, 0x0001); - - return count; -}