Hi Jagan,
On 17 October 2017 at 00:53, Jagan Teki jagannadh.teki@gmail.com wrote:
- Tom
On 17-Oct-2017 12:44 AM, "Jagan Teki" jagannadh.teki@gmail.com wrote:
Hi,
I'm trying to use SPL_OF_CONTROL with u-boot,dm-spl So I've marked u-boot,dm-spl with pinctrl since MMC used the pinconfig.
The issue observed here is SPL handover to U-Boot proper and before relocation U-Boot probed imx_thermal dm-driver through device_probe. But the same time device_probe unnecessary probing all u-boot,dm-spl marked nodes(which are strictly related for SPL) Since pinctrl marked as u-boot, dm-spl the same probed and this might be the show-stopper.
Based on the data abort, the code hang at relocation code, relocate.S, eventually stop calling uclass_get_device( was called in arch/arm/mach-imx/cpu.c) during board_f or unmark u-boot,dm-spl make U-Boot boots.
Below are relocation code hang point and Log dump, request for any inputs.
Relocation code:
/* relative fix: increase location by offset */ add r0, r0, r487800ac4: e0800004 add r0, r0, r4 ldr r1, [r0] 87800ac8: e5901000 ldr r1, [r0] /* HANG */ add r1, r1, r4 87800acc: e0811004 add r1, r1, r4 str r1, [r0] 87800ad0: e5801000 str r1, [r0]
87800ad4 <fixnext>:
Log:
U-Boot SPL 2017.11-rc1-00165-g7340683-dirty (Oct 17 2017 - 04:00:01) Trying to boot from MMC1
device_probe: Process pinctrl for soc
device_probe: Process pinctrl for aips-bus@02000000 initialized IMX pinctrl driver
device_probe: Process pinctrl for aips-bus@02100000
device_probe: Process pinctrl for usdhc@02190000
device_probe: Process pinctrl for usdhc1grp
device_probe: Process pinctrl for gpio@0209c000 Expected Linux image is not found. Trying to start U-boot
U-Boot 2017.11-rc1-00165-g7340683-dirty (Oct 17 2017 - 04:00:01 +0530)
U-Boot code: 87800000 -> 8783FB38 BSS: -> 87857338 CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) device_probe: Process pinctrl for imx_thermal
device_probe: Process pinctrl for soc
device_probe: Process pinctrl for aips-bus@02000000 initialized IMX pinctrl driver at 31C Reset cause: POR Model: Engicam Is.IoT MX6UL MMC Starterkit DRAM: Monitor len: 00057338 Ram size: 08000000 Ram top: 88000000 TLB table from 87ff0000 to 87ff4000 Reserving 348k for U-Boot at: 87f98000 Reserving 16384k for malloc() at: 86f98000 Reserving 80 Bytes for Board Info at: 86f97fb0 Reserving 240 Bytes for Global Data at: 86f97ec0 Reserving 24448 Bytes for FDT at: 86f91f40
RAM Configuration: Bank #0: 80000000 DRAM: 128 MiB New Stack Pointer is: 86f91f20 Relocation Offset is: 00798000 Relocating to 87f98000, new gd at 86f97ec0, sp at 86f91f20 data abort pc : [<87800ac8>] lr : [<87f986ac>] sp : 86f91f20 ip : 0000001c fp : 00000017 r10: 8783fa98 r9 : 86f97ec0 r8 : 00913b18 r7 : deadbeef r6 : 0091de88 r5 : 87800320 r4 : 00798000 r3 : 87848848 r2 : 87843820 r1 : 00000017 r0 : 02878000 Flags: nZCv IRQs off FIQs off Mode SVC_32 Resetting CPU ...
resetting ...
thanks!
Jagan Teki Free Software Engineer | www.openedev.com U-Boot, Linux | Upstream Maintainer Hyderabad, India.
I am no sure of the issue, but I suggest debugging it for a root cause.
Regards, Simon