Hi Neil,
On Tue, 30 Jun 2020 at 18:30, Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 30/06/2020 13:33, Anand Moon wrote:
Hi Beniamino,
On Wed, 6 May 2020 at 01:53, Beniamino Galvani b.galvani@gmail.com wrote:
Hi,
these two patches add initial u-boot support for Hardkernel ODROID-C4.
https://wiki.odroid.com/odroid-c4/odroid-c4
Beniamino Galvani (2): arm: dts: import ODROID-C4 device tree boards: amlogic: add ODROID-C4 support
Can you respin this patches, I would like to see these get merged in the current u-boot release
-Anand
The Odroid-C4 could re-use the new Odroid-N2 board support I submitted at [1]
Anand, is the MAC address stored stored the same way on the C4 ?
Neil
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200618144037.23392-1-narm...
I gave this patches a try on latest u-boot but I cannot make my Odroid C4 to boot up uinsg microSD card and eMMC Here are the logs.
SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:800;NAND:81;SD?:0;SD:0;READ:0;0.0;CHK:0; bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02
no sdio debug board detected L0:00000000 L1:00000703 L2:00008067 L3:15000020 S1:00000000 B2:20282000 B1:a0f83180
TE: 260148
BL2 Built : 22:54:32, Apr 28 2020. g12a ga659aac-dirty - changqing.gao@droid11
Board ID = 1 Set cpu clk to 24M Set clk81 to 24M Use GP1_pll as DSU clk. DSU clk: 1200 Mhz CPU clk: 1200 MHz Set clk81 to 166.6M DDR driver_vesion: LPDDR4_PHY_V_0_1_15 build time: Apr 28 2020 22:54:28 board id: 1 Load FIP HDR from SD, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0 fw parse done Load ddrfw from SD, src: 0x00030200, des: 0xfffd0000, size: 0x0000c000, part: 0 Load ddrfw from SD, src: 0x0002c200, des: 0xfffd0000, size: 0x00004000, part: 0 PIEI prepare done fastboot data load fastboot data verify verify result: 255 Cfg max: 2, cur: 1. Board id: 255. Force loop cfg DDR4 probe ddr clk to 1320MHz Load ddrfw from SD, src: 0x00014200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001 Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of Write leveling coarse delay INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from SD, src: 0x00020200, des: 0xfffd0000, size: 0x0000c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully!
R0_RxClkDly_Margin==106 ps 9 R0_TxDqDly_Margi==118 ps 10
R1_RxClkDly_Margin==0 ps 0 R1_TxDqDly_Margi==0 ps 0
dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001
soc_vref_reg_value 0x 0000004e 0000004e 0000004e 0000004d 0000004f 0000004e 0000004e 0000004f 0000004c 0000004d 0000004e 0000004c 0000004c 0000004e 0000004f 0000004e 00000050 0000004e 0000004d 0000004e 0000004e 0000004c 0000004d 0000004d 0000004d 0000004f 0000004f 0000004f 0000004d 0000004d 0000004d 0000004f dram_vref_reg_value 0x 00000021 2D training succeed aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:43 auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 2048MB DMC_DDR_CTRL: 00700024DDR size: 3928MB cs0 DataBus test pass cs1 DataBus test pass cs0 AddrBus test pass cs1 AddrBus test pass
non-sec scramble use zero key ddr scramble enabled
100bdlr_step_size ps== 461 result report boot times 0Enable ddr reg access Load FIP HDR from SD, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0 Load BL3X from SD, src: 0x0003c200, des: 0x0172c000, size: 0x00090000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 MVN_1=0x00000000 MVN_2=0x00000000 [Image: g12a_v1.1.3386-3b31431 2019-05-21 10:41:54 luan.yuan@droid15-sz] OPS=0x10 ring efuse init 2b 0c 10 00 01 13 20 00 00 0f 36 30 43 57 50 50 [0.017319 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):4fc40b1 NOTICE: BL31: Built : 15:57:33, May 22 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast
U-Boot 2020.07-rc5-00076-g46e5b60e21 (Jun 30 2020 - 21:08:25 +0530) odroid-c4
Model: Hardkernel ODROID-C4 SoC: Amlogic Meson SM1 (Unknown) Revision 2b:c (10:2) DRAM: 3.8 GiB MMC: sd@ffe05000: 0, mmc@ffe07000: 1 stdio_add_devices: Video device failed (ret=-22) In: serial@3000 Out: serial@3000 Err: serial@3000 Net: Could not get PHY for ethernet@ff3f0000: addr 8 No ethernet found.
Hit any key to stop autoboot: 0
-Anand