Hi Sjoerd,
On 12/12/2023 23:02, Sjoerd Simons wrote:
Add glue code for TI AM62 to the dwc3 driver; Most code adopted from TI vendor u-boot code.
Signed-off-by: Sjoerd Simons sjoerd@collabora.com Reviewed-by: Mattijs Korpershoek mkorpershoek@baylibre.com
(no changes since v2)
Changes in v2:
- Switch dwc3 glue to a seperate driver rather then in dwc-generic
drivers/usb/dwc3/Kconfig | 14 ++++ drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-am62.c | 125 +++++++++++++++++++++++++++++++++++ 3 files changed, 140 insertions(+) create mode 100644 drivers/usb/dwc3/dwc3-am62.c
diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig index c0c8c16fd9c..26a1e1770c5 100644 --- a/drivers/usb/dwc3/Kconfig +++ b/drivers/usb/dwc3/Kconfig @@ -37,6 +37,20 @@ config SPL_USB_DWC3_GENERIC Select this for Xilinx ZynqMP and similar Platforms. This wrapper supports Host and Peripheral operation modes.
+config SPL_USB_DWC3_AM62
- bool "TI AM62 USB wrapper"
- depends on SPL_DM_USB && SPL_USB_DWC3_GENERIC
- help
Select this for TI AM62 Platforms.This wrapper supports Host and Peripheral operation modes.+config USB_DWC3_AM62
- bool "TI AM62 USB wrapper"
- depends on DM_USB && USB_DWC3_GENERIC
- help
Select this for TI AM62 Platforms.This wrapper supports Host and Peripheral operation modes.config USB_DWC3_MESON_G12A bool "Amlogic Meson G12A USB wrapper" depends on DM_USB && USB_DWC3 && ARCH_MESON diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile index 97b4f7191ca..a46b6824ab7 100644 --- a/drivers/usb/dwc3/Makefile +++ b/drivers/usb/dwc3/Makefile @@ -6,6 +6,7 @@ dwc3-y := core.o
obj-$(CONFIG_USB_DWC3_GADGET) += gadget.o ep0.o
+obj-$(CONFIG_$(SPL_)USB_DWC3_AM62) += dwc3-am62.o obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o obj-$(CONFIG_USB_DWC3_MESON_GXL) += dwc3-meson-gxl.o diff --git a/drivers/usb/dwc3/dwc3-am62.c b/drivers/usb/dwc3/dwc3-am62.c new file mode 100644 index 00000000000..56c3b26a531 --- /dev/null +++ b/drivers/usb/dwc3/dwc3-am62.c @@ -0,0 +1,125 @@ +// SPDX-License-Identifier: GPL-2.0 +/*
- TI AM62 specific glue layer for DWC3
- */
+#include <dm.h> +#include <dm/device_compat.h> +#include <regmap.h> +#include <syscon.h> +#include <asm/io.h>
+#include "dwc3-generic.h"
+static void dwc3_ti_am62_glue_configure(struct udevice *dev, int index,
enum usb_dr_mode mode)+{ +#define USBSS_MODE_CONTROL 0x1c +#define USBSS_PHY_CONFIG 0x8 +#define USBSS_PHY_VBUS_SEL_MASK GENMASK(2, 1) +#define USBSS_PHY_VBUS_SEL_SHIFT 1 +#define USBSS_MODE_VALID BIT(0) +#define PHY_PLL_REFCLK_MASK GENMASK(3, 0) +static const int dwc3_ti_am62_rate_table[] = { /* in KHZ */
- 9600,
- 10000,
- 12000,
- 19200,
- 20000,
- 24000,
- 25000,
- 26000,
- 38400,
- 40000,
- 58000,
- 50000,
- 52000,
+};
Can we please move these defines and dwc3_ti_am62_rate_table outside the function?
- struct clk usb2_refclk;
- int rate_code, i, ret;
- unsigned long rate;
- u32 reg;
- void *usbss;
- bool vbus_divider;
- struct regmap *syscon;
- struct ofnode_phandle_args args;
- usbss = dev_remap_addr_index(dev, 0);
- if (IS_ERR(usbss)) {
dev_err(dev, "can't map IOMEM resource\n");return;- }
- ret = clk_get_by_name(dev, "ref", &usb2_refclk);
- if (ret) {
dev_err(dev, "can't get usb2_refclk\n");return;- }
- /* Calculate the rate code */
- rate = clk_get_rate(&usb2_refclk);
- rate /= 1000; /* To KHz */
- for (i = 0; i < ARRAY_SIZE(dwc3_ti_am62_rate_table); i++) {
if (dwc3_ti_am62_rate_table[i] == rate)break;- }
- if (i == ARRAY_SIZE(dwc3_ti_am62_rate_table)) {
dev_err(dev, "unsupported usb2_refclk rate: %lu KHz\n", rate);return;- }
- rate_code = i;
- /* Read the syscon property */
- syscon = syscon_regmap_lookup_by_phandle(dev, "ti,syscon-phy-pll-refclk");
- if (IS_ERR(syscon)) {
dev_err(dev, "unable to get ti,syscon-phy-pll-refclk regmap\n");return;- }
- ret = ofnode_parse_phandle_with_args(dev_ofnode(dev), "ti,syscon-phy-pll-refclk", NULL, 1,
0, &args);- if (ret)
return;- /* Program PHY PLL refclk by reading syscon property */
- ret = regmap_update_bits(syscon, args.args[0], PHY_PLL_REFCLK_MASK, rate_code);
- if (ret) {
dev_err(dev, "failed to set phy pll reference clock rate\n");return;- }
- /* VBUS divider select */
- reg = readl(usbss + USBSS_PHY_CONFIG);
- vbus_divider = dev_read_bool(dev, "ti,vbus-divider");
- if (vbus_divider)
reg |= 1 << USBSS_PHY_VBUS_SEL_SHIFT;- writel(reg, usbss + USBSS_PHY_CONFIG);
- /* Set mode valid */
- reg = readl(usbss + USBSS_MODE_CONTROL);
- reg |= USBSS_MODE_VALID;
- writel(reg, usbss + USBSS_MODE_CONTROL);
+}
+struct dwc3_glue_ops ti_am62_ops = {
- .glue_configure = dwc3_ti_am62_glue_configure,
+};
+static const struct udevice_id dwc3_am62_match[] = {
- { .compatible = "ti,am62-usb", .data = (ulong)&ti_am62_ops },
- { /* sentinel */ }
+};
+U_BOOT_DRIVER(dwc3_am62_wrapper) = {
- .name = "dwc3-am62",
- .id = UCLASS_SIMPLE_BUS,
- .of_match = dwc3_am62_match,
- .bind = dwc3_glue_bind,
- .probe = dwc3_glue_probe,
- .remove = dwc3_glue_remove,
- .plat_auto = sizeof(struct dwc3_glue_data),
+};