Altera Cyclone 5 board is very different board (big, rectangular, expensive) than EBV Socrates (small, circular, cheap) board. Different parts are used there, too, but same configuration of u-boot works on both. Nevertheless, printing wrong name confuses users. Virtual target is completely different, and board configured for it will not boot on physical targets.
Therefore this splits the configuration so that u-boot knows they are different. So far it is only used for correcting the puts, but there may be other uses in future.
Signed-off-by: Pavel Machek pavel@denx.de
---
Diff from v1: separate virtual target, too, and make it apply to recent u-boot.
diff --git a/board/altera/socfpga/socfpga_cyclone5.c b/board/altera/socfpga/socfpga_cyclone5.c index a960eb6..33946b6 100644 --- a/board/altera/socfpga/socfpga_cyclone5.c +++ b/board/altera/socfpga/socfpga_cyclone5.c @@ -28,7 +28,7 @@ int print_cpuinfo(void) */ int checkboard(void) { - puts("BOARD : Altera SOCFPGA Cyclone5 Board\n"); + puts("BOARD : " ALTERA_BOARD_NAME "\n"); return 0; }
diff --git a/boards.cfg b/boards.cfg index 221b7f8..6eebbf5 100644 --- a/boards.cfg +++ b/boards.cfg @@ -379,6 +379,8 @@ Active arm armv7 rmobile renesas lager Active arm armv7 s5pc1xx samsung goni s5p_goni - Przemyslaw Marczak p.marczak@samsung.com Active arm armv7 s5pc1xx samsung smdkc100 smdkc100 - Minkyu Kang mk7.kang@samsung.com Active arm armv7 socfpga altera socfpga socfpga_cyclone5 - - +Active arm armv7 socfpga altera socfpga socfpga_virtual - - +Active arm armv7 socfpga altera socfpga socfpga_socrates - - Active arm armv7 u8500 st-ericsson snowball snowball - Mathieu Poirier mathieu.poirier@linaro.org Active arm armv7 u8500 st-ericsson u8500 u8500_href - - Active arm armv7 vf610 freescale vf610twr vf610twr vf610twr:IMX_CONFIG=board/freescale/vf610twr/imximage.cfg Alison Wang b18965@freescale.com diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h new file mode 100644 index 0000000..4d90952 --- /dev/null +++ b/include/configs/socfpga_common.h @@ -0,0 +1,240 @@ +/* + * Copyright (C) 2012 Altera Corporation <www.altera.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#ifndef __CONFIG_COMMON_H +#define __CONFIG_COMMON_H + +#include <asm/arch/socfpga_base_addrs.h> +#include "../../board/altera/socfpga/pinmux_config.h" +#include "../../board/altera/socfpga/pll_config.h" + +/* + * High level configuration + */ + +#define CONFIG_SYS_GENERIC_BOARD + +#define CONFIG_ARMV7 +#define CONFIG_SYS_DCACHE_OFF +#undef CONFIG_USE_IRQ + +#define CONFIG_MISC_INIT_R +#define CONFIG_SINGLE_BOOTLOADER +#define CONFIG_SOCFPGA + +/* base address for .text section */ +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_SYS_TEXT_BASE 0x08000040 +#else +#define CONFIG_SYS_TEXT_BASE 0x01000040 +#endif +#define CONFIG_SYS_LOAD_ADDR 0x7fc0 + +/* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 +/* Monitor Command Prompt */ +#define CONFIG_SYS_PROMPT "SOCFPGA_CYCLONE5 # " +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) + +/* + * Display CPU and Board Info + */ +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +/* + * Enable early stage initialization at C environment + */ +#define CONFIG_BOARD_EARLY_INIT_F + +/* flat device tree */ +#define CONFIG_OF_LIBFDT +/* skip updating the FDT blob */ +#define CONFIG_FDT_BLOB_SKIP_UPDATE +/* Initial Memory map size for Linux, minus 4k alignment for DFT blob */ +#define CONFIG_SYS_BOOTMAPSZ ((256*1024*1024) - (4*1024)) + +#define CONFIG_SPL_RAM_DEVICE +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR +#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start)) +#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start) + +/* + * Memory allocation (MALLOC) + */ +/* Room required on the stack for the environment data */ +#define CONFIG_ENV_SIZE 1024 +/* Size of DRAM reserved for malloc() use */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) + +/* SP location before relocation, must use scratch RAM */ +#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 +/* Reserving 0x100 space at back of scratch RAM for debug info */ +#define CONFIG_SYS_INIT_RAM_SIZE (0x10000 - 0x100) +/* Stack pointer prior relocation, must situated at on-chip RAM */ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) + + +/* + * Command line configuration. + */ +#define CONFIG_SYS_NO_FLASH +#include <config_cmd_default.h> +/* FAT file system support */ +#define CONFIG_CMD_FAT + + +/* + * Misc + */ +#define CONFIG_DOS_PARTITION 1 + +#ifdef CONFIG_SPL_BUILD +#undef CONFIG_PARTITIONS +#endif + +/* + * Environment setup + */ + +/* Delay before automatically booting the default image */ +#define CONFIG_BOOTDELAY 3 +/* Enable auto completion of commands using TAB */ +#define CONFIG_AUTO_COMPLETE +/* use "hush" command parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMD_RUN + +#define CONFIG_BOOTCOMMAND "run ramboot" + +/* + * arguments passed to the bootm command. The value of + * CONFIG_BOOTARGS goes into the environment value "bootargs". + * Do note the value will overide also the chosen node in FDT blob. + */ +#define CONFIG_BOOTARGS "console=ttyS0,57600,mem=256M@0x0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "verify=n\0" \ + "loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \ + "bootm ${loadaddr} - ${fdt_addr}\0" \ + "bootimage=uImage\0" \ + "fdt_addr=100\0" \ + "fsloadcmd=ext2load\0" \ + "bootm ${loadaddr} - ${fdt_addr}\0" \ + "qspiroot=/dev/mtdblock0\0" \ + "qspirootfstype=jffs2\0" \ + "qspiboot=setenv bootargs " CONFIG_BOOTARGS \ + " root=${qspiroot} rw rootfstype=${qspirootfstype};"\ + "bootm ${loadaddr} - ${fdt_addr}\0" + +/* using environment setting for stdin, stdout, stderr */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +/* Enable the call to overwrite_console() */ +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +/* Enable overwrite of previous console environment settings */ +#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE + +/* max number of command args */ +#define CONFIG_SYS_MAXARGS 16 + + +/* + * Hardware drivers + */ + +/* + * SDRAM Memory Map + */ +/* We have 1 bank of DRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +/* SDRAM Bank #1 */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +/* SDRAM memory size */ +#define PHYS_SDRAM_1_SIZE 0x40000000 + +#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_START 0x00000000 +#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE + +/* + * NS16550 Configuration + */ +#define UART0_BASE SOCFPGA_UART0_ADDRESS +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_COM1 UART0_BASE +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define V_NS16550_CLK 1000000 +#else +#define V_NS16550_CLK 100000000 +#endif +#define CONFIG_BAUDRATE 115200 + +/* + * FLASH + */ +#define CONFIG_SYS_NO_FLASH + +/* + * L4 OSC1 Timer 0 + */ +/* This timer use eosc1 where the clock frequency is fixed + * throughout any condition */ +#define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS +/* reload value when timer count to zero */ +#define TIMER_LOAD_VAL 0xFFFFFFFF +/* Timer info */ +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_SYS_TIMER_RATE 2400000 +#else +#define CONFIG_SYS_TIMER_RATE 25000000 +#endif +#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) + +#define CONFIG_ENV_IS_NOWHERE + +/* + * SPL "Second Program Loader" aka Initial Software + */ + +/* Enable building of SPL globally */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK + +/* TEXT_BASE for linking the SPL binary */ +#define CONFIG_SPL_TEXT_BASE 0xFFFF0000 + +/* Stack size for SPL */ +#define CONFIG_SPL_STACK_SIZE (4 * 1024) + +/* MALLOC size for SPL */ +#define CONFIG_SPL_MALLOC_SIZE (5 * 1024) + +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_BOARD_INIT + +#define CHUNKSZ_CRC32 (1 * 1024) + +#define CONFIG_CRC32_VERIFY + +/* Linker script for SPL */ +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds" + +/* Support for common/libcommon.o in SPL binary */ +#define CONFIG_SPL_LIBCOMMON_SUPPORT +/* Support for lib/libgeneric.o in SPL binary */ +#define CONFIG_SPL_LIBGENERIC_SUPPORT + +#endif /* __CONFIG_COMMON_H */ diff --git a/include/configs/socfpga_cyclone5.h b/include/configs/socfpga_cyclone5.h index 517070c..d5d59d2 100644 --- a/include/configs/socfpga_cyclone5.h +++ b/include/configs/socfpga_cyclone5.h @@ -1,242 +1,16 @@ /* - * Copyright (C) 2012 Altera Corporation <www.altera.com> + * Copyright (C) 2014 Pavel Machek pavel@denx.de * - * SPDX-License-Identifier: GPL-2.0+ + * SPDX-License-Identifier: GPL-2.0+ */ #ifndef __CONFIG_H #define __CONFIG_H
-#include <asm/arch/socfpga_base_addrs.h> -#include "../../board/altera/socfpga/pinmux_config.h" -#include "../../board/altera/socfpga/pll_config.h" - -/* - * High level configuration - */ /* Virtual target or real hardware */ -#define CONFIG_SOCFPGA_VIRTUAL_TARGET - -#define CONFIG_SYS_GENERIC_BOARD - -#define CONFIG_ARMV7 -#define CONFIG_SYS_DCACHE_OFF -#undef CONFIG_USE_IRQ - -#define CONFIG_MISC_INIT_R -#define CONFIG_SINGLE_BOOTLOADER -#define CONFIG_SOCFPGA - -/* base address for .text section */ -#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET -#define CONFIG_SYS_TEXT_BASE 0x08000040 -#else -#define CONFIG_SYS_TEXT_BASE 0x01000040 -#endif -#define CONFIG_SYS_LOAD_ADDR 0x7fc0 - -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Monitor Command Prompt */ -#define CONFIG_SYS_PROMPT "SOCFPGA_CYCLONE5 # " -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) - -/* - * Display CPU and Board Info - */ -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DISPLAY_BOARDINFO - -/* - * Enable early stage initialization at C environment - */ -#define CONFIG_BOARD_EARLY_INIT_F - -/* flat device tree */ -#define CONFIG_OF_LIBFDT -/* skip updating the FDT blob */ -#define CONFIG_FDT_BLOB_SKIP_UPDATE -/* Initial Memory map size for Linux, minus 4k alignment for DFT blob */ -#define CONFIG_SYS_BOOTMAPSZ ((256*1024*1024) - (4*1024)) - -#define CONFIG_SPL_RAM_DEVICE -#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR -#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start)) -#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start) - -/* - * Memory allocation (MALLOC) - */ -/* Room required on the stack for the environment data */ -#define CONFIG_ENV_SIZE 1024 -/* Size of DRAM reserved for malloc() use */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* SP location before relocation, must use scratch RAM */ -#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 -/* Reserving 0x100 space at back of scratch RAM for debug info */ -#define CONFIG_SYS_INIT_RAM_SIZE (0x10000 - 0x100) -/* Stack pointer prior relocation, must situated at on-chip RAM */ -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - - -/* - * Command line configuration. - */ -#define CONFIG_SYS_NO_FLASH -#include <config_cmd_default.h> -/* FAT file system support */ -#define CONFIG_CMD_FAT - - -/* - * Misc - */ -#define CONFIG_DOS_PARTITION 1 - -#ifdef CONFIG_SPL_BUILD -#undef CONFIG_PARTITIONS -#endif - -/* - * Environment setup - */ - -/* Delay before automatically booting the default image */ -#define CONFIG_BOOTDELAY 3 -/* Enable auto completion of commands using TAB */ -#define CONFIG_AUTO_COMPLETE -/* use "hush" command parser */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_CMD_RUN - -#define CONFIG_BOOTCOMMAND "run ramboot" - -/* - * arguments passed to the bootm command. The value of - * CONFIG_BOOTARGS goes into the environment value "bootargs". - * Do note the value will overide also the chosen node in FDT blob. - */ -#define CONFIG_BOOTARGS "console=ttyS0,57600,mem=256M@0x0" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "verify=n\0" \ - "loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ - "ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \ - "bootm ${loadaddr} - ${fdt_addr}\0" \ - "bootimage=uImage\0" \ - "fdt_addr=100\0" \ - "fsloadcmd=ext2load\0" \ - "bootm ${loadaddr} - ${fdt_addr}\0" \ - "qspiroot=/dev/mtdblock0\0" \ - "qspirootfstype=jffs2\0" \ - "qspiboot=setenv bootargs " CONFIG_BOOTARGS \ - " root=${qspiroot} rw rootfstype=${qspirootfstype};"\ - "bootm ${loadaddr} - ${fdt_addr}\0" - -/* using environment setting for stdin, stdout, stderr */ -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -/* Enable the call to overwrite_console() */ -#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE -/* Enable overwrite of previous console environment settings */ -#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE - -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 - - -/* - * Hardware drivers - */ - -/* - * SDRAM Memory Map - */ -/* We have 1 bank of DRAM */ -#define CONFIG_NR_DRAM_BANKS 1 -/* SDRAM Bank #1 */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -/* SDRAM memory size */ -#define PHYS_SDRAM_1_SIZE 0x40000000 - -#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_START 0x00000000 -#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE - -/* - * NS16550 Configuration - */ -#define UART0_BASE SOCFPGA_UART0_ADDRESS -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE -4 -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550_COM1 UART0_BASE -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} -#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET -#define V_NS16550_CLK 1000000 -#else -#define V_NS16550_CLK 100000000 -#endif -#define CONFIG_BAUDRATE 115200 - -/* - * FLASH - */ -#define CONFIG_SYS_NO_FLASH - -/* - * L4 OSC1 Timer 0 - */ -/* This timer use eosc1 where the clock frequency is fixed - * throughout any condition */ -#define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS -/* reload value when timer count to zero */ -#define TIMER_LOAD_VAL 0xFFFFFFFF -/* Timer info */ -#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET -#define CONFIG_SYS_TIMER_RATE 2400000 -#else -#define CONFIG_SYS_TIMER_RATE 25000000 -#endif -#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) - -#define CONFIG_ENV_IS_NOWHERE - -/* - * SPL "Second Program Loader" aka Initial Software - */ - -/* Enable building of SPL globally */ -#define CONFIG_SPL -#define CONFIG_SPL_FRAMEWORK - -/* TEXT_BASE for linking the SPL binary */ -#define CONFIG_SPL_TEXT_BASE 0xFFFF0000 - -/* Stack size for SPL */ -#define CONFIG_SPL_STACK_SIZE (4 * 1024) - -/* MALLOC size for SPL */ -#define CONFIG_SPL_MALLOC_SIZE (5 * 1024) - -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_BOARD_INIT - -#define CHUNKSZ_CRC32 (1 * 1024) - -#define CONFIG_CRC32_VERIFY +#undef CONFIG_SOCFPGA_VIRTUAL_TARGET
-/* Linker script for SPL */ -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds" +#include <configs/socfpga_common.h>
-/* Support for common/libcommon.o in SPL binary */ -#define CONFIG_SPL_LIBCOMMON_SUPPORT -/* Support for lib/libgeneric.o in SPL binary */ -#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define ALTERA_BOARD_NAME "Altera SOCFPGA Cyclone5 Board"
-#endif /* __CONFIG_H */ +#endif /* __CONFIG_H */ diff --git a/include/configs/socfpga_socrates.h b/include/configs/socfpga_socrates.h new file mode 100644 index 0000000..27e0261 --- /dev/null +++ b/include/configs/socfpga_socrates.h @@ -0,0 +1,16 @@ +/* + * Copyright (C) 2014 Pavel Machek pavel@denx.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* Virtual target or real hardware */ +#undef CONFIG_SOCFPGA_VIRTUAL_TARGET + +#include <configs/socfpga_common.h> + +#define ALTERA_BOARD_NAME "EBV SoCrates - Cyclone V SoC FPGA Board" + +#endif /* __CONFIG_H */ diff --git a/include/configs/socfpga_virtual.h b/include/configs/socfpga_virtual.h new file mode 100644 index 0000000..cf871e2 --- /dev/null +++ b/include/configs/socfpga_virtual.h @@ -0,0 +1,16 @@ +/* + * Copyright (C) 2014 Pavel Machek pavel@denx.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* Virtual target or real hardware */ +#define CONFIG_SOCFPGA_VIRTUAL_TARGET + +#include <configs/socfpga_common.h> + +#define ALTERA_BOARD_NAME "SOCFPGA Virtual Board" + +#endif /* __CONFIG_H */