[PATCH v5 38/39] dts: qcs404-evb: replace with upstream DT

Drop the U-Boot specific DTS in favour of upstream. We'll only include the -4000 variant as that is what U-Boot already supported.

Taken from kernel tag v6.7

Reviewed-by: Neil Armstrong neil.armstrong@linaro.org Reviewed-by: Sumit Garg sumit.garg@linaro.org Signed-off-by: Caleb Connolly caleb.connolly@linaro.org --- arch/arm/dts/Makefile | 2 +- arch/arm/dts/pms405.dtsi | 149 +++ arch/arm/dts/qcs404-evb-4000-u-boot.dtsi | 48 + arch/arm/dts/qcs404-evb-4000.dts | 96 ++ arch/arm/dts/qcs404-evb-uboot.dtsi | 30 - arch/arm/dts/qcs404-evb.dts | 390 ------- arch/arm/dts/qcs404-evb.dtsi | 389 +++++++ arch/arm/dts/qcs404.dtsi | 1829 ++++++++++++++++++++++++++++++ 8 files changed, 2512 insertions(+), 421 deletions(-)

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 0193833845f3..cab3bb832dbc 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -635,9 +635,9 @@ dtb-$(CONFIG_TARGET_TEN64) += fsl-ls1088a-ten64.dtb dtb-$(CONFIG_ARCH_SNAPDRAGON) += apq8016-sbc.dtb \ apq8096-db820c.dtb \ sdm845-db845c.dtb \ sdm845-samsung-starqltechn.dtb \ - qcs404-evb.dtb + qcs404-evb-4000.dtb

dtb-$(CONFIG_TARGET_STEMMY) += ste-ux500-samsung-stemmy.dtb

dtb-$(CONFIG_STM32F4) += stm32f429-disco.dtb \ diff --git a/arch/arm/dts/pms405.dtsi b/arch/arm/dts/pms405.dtsi new file mode 100644 index 000000000000..461ad97032f7 --- /dev/null +++ b/arch/arm/dts/pms405.dtsi @@ -0,0 +1,149 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018, Linaro Limited + */ + +#include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/iio/qcom,spmi-vadc.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + thermal-zones { + pms405-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&pms405_temp>; + + trips { + pms405_alert0: pms405-alert0 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + pms405_crit: pms405-crit { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; +}; + +&spmi_bus { + pms405_0: pms405@0 { + compatible = "qcom,pms405", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pms405_gpios: gpio@c000 { + compatible = "qcom,pms405-gpio", "qcom,spmi-gpio"; + reg = <0xc000>; + gpio-controller; + gpio-ranges = <&pms405_gpios 0 0 12>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pon@800 { + compatible = "qcom,pms405-pon"; + reg = <0x0800>; + mode-bootloader = <0x2>; + mode-recovery = <0x1>; + + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + }; + }; + + pms405_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; + io-channels = <&pms405_adc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pms405_adc: adc@3100 { + compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2"; + reg = <0x3100>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + + channel@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + channel@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + channel@131 { + reg = <ADC5_VPH_PWR>; + qcom,pre-scaling = <1 3>; + label = "vph_pwr"; + }; + + channel@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + + channel@77 { + reg = <ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "pa_therm1"; + }; + + channel@79 { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "pa_therm3"; + }; + + channel@76 { + reg = <ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "xo_therm"; + }; + }; + + rtc@6000 { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>, <0x6100>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; + }; + }; + + pms405_1: pms405@1 { + compatible = "qcom,pms405", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + + pms405_spmi_regulators: regulators { + compatible = "qcom,pms405-regulators"; + }; + }; +}; diff --git a/arch/arm/dts/qcs404-evb-4000-u-boot.dtsi b/arch/arm/dts/qcs404-evb-4000-u-boot.dtsi new file mode 100644 index 000000000000..d3033ea42ec1 --- /dev/null +++ b/arch/arm/dts/qcs404-evb-4000-u-boot.dtsi @@ -0,0 +1,48 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include <dt-bindings/gpio/gpio.h> + +/delete-node/ &usb3_vbus_reg; +/delete-node/ &usb_vbus_boost_pin; + +/ { + /* U-Boot uses different bindings for GPIO regulators, this + * one is required for USB + */ + usb3_vbus_reg: usb3_vbus_reg { + compatible = "regulator-gpio"; + regulator-name = "usb3_vbus_reg"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-gpios = <&pms405_gpios 3 GPIO_ACTIVE_HIGH>; + enable-active-high; + states = <0 0>, <5000000 1>; + }; +}; + +&blsp1_uart2 { + /* This defines the bit clock divider which defines the baud rate. + * 0xFF is a divider of 16 for both the RX and TX lines. The QCS404 + * clock driver in U-Boot hardcodes a 1843200Hz frequency for the + * UART core clock, and 1843200 / 16 = 115200. + */ + bit-rate = <0xFF>; +}; + +&gcc { + /* The clock framework in U-Boot "sort of" has the idea of linking an + * individual clock to a device via uclass_priv. However the qcom clock + * driver instead associates many clocks with a single device. This is + * usually fine but it seems that assigned-clocks wreak havoc on this + * and we wind up having a reference to the XO clock which is associated + * with the qcom_clk device... + * For now we'll just remove these properties, no other board has these. + */ + /delete-property/ assigned-clock-rates; + /delete-property/ assigned-clocks; +}; + +&usb3_dwc3 { + /* Make sure the VBUS supply is switched on */ + vbus-supply = <&usb3_vbus_reg>; +}; diff --git a/arch/arm/dts/qcs404-evb-4000.dts b/arch/arm/dts/qcs404-evb-4000.dts new file mode 100644 index 000000000000..358827c2fbd3 --- /dev/null +++ b/arch/arm/dts/qcs404-evb-4000.dts @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018, Linaro Limited + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include "qcs404-evb.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. QCS404 EVB 4000"; + compatible = "qcom,qcs404-evb-4000", "qcom,qcs404-evb", + "qcom,qcs404"; +}; + +&ethernet { + status = "okay"; + + snps,reset-gpio = <&tlmm 60 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 10000>; + + pinctrl-names = "default"; + pinctrl-0 = <&ethernet_defaults>; + + phy-handle = <&phy1>; + phy-mode = "rgmii"; + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy1: phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + device_type = "ethernet-phy"; + reg = <0x4>; + }; + }; +}; + +&tlmm { + ethernet_defaults: ethernet-defaults-state { + int-pins { + pins = "gpio61"; + function = "rgmii_int"; + bias-disable; + drive-strength = <2>; + }; + mdc-pins { + pins = "gpio76"; + function = "rgmii_mdc"; + bias-pull-up; + }; + mdio-pins { + pins = "gpio75"; + function = "rgmii_mdio"; + bias-pull-up; + }; + tx-pins { + pins = "gpio67", "gpio66", "gpio65", "gpio64"; + function = "rgmii_tx"; + bias-pull-up; + drive-strength = <16>; + }; + rx-pins { + pins = "gpio73", "gpio72", "gpio71", "gpio70"; + function = "rgmii_rx"; + bias-disable; + drive-strength = <2>; + }; + tx-ctl-pins { + pins = "gpio68"; + function = "rgmii_ctl"; + bias-pull-up; + drive-strength = <16>; + }; + rx-ctl-pins { + pins = "gpio74"; + function = "rgmii_ctl"; + bias-disable; + drive-strength = <2>; + }; + tx-ck-pins { + pins = "gpio63"; + function = "rgmii_ck"; + bias-pull-up; + drive-strength = <16>; + }; + rx-ck-pins { + pins = "gpio69"; + function = "rgmii_ck"; + bias-disable; + drive-strength = <2>; + }; + }; +}; diff --git a/arch/arm/dts/qcs404-evb-uboot.dtsi b/arch/arm/dts/qcs404-evb-uboot.dtsi deleted file mode 100644 index b4c5f3fa4301..000000000000 --- a/arch/arm/dts/qcs404-evb-uboot.dtsi +++ /dev/null @@ -1,30 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * U-Boot addition to handle QCS404 EVB pre-relocation devices - * - * (C) Copyright 2022 Sumit Garg sumit.garg@linaro.org - */ - -/ { - soc { - bootph-all; - - pinctrl_north@1300000 { - bootph-all; - }; - - clock-controller@1800000 { - bootph-all; - }; - - serial@78b1000 { - bootph-all; - }; - }; -}; - -&pms405_gpios { - usb_vbus_boost_pin { - gpios = <&pms405_gpios 2 0>; - }; -}; diff --git a/arch/arm/dts/qcs404-evb.dts b/arch/arm/dts/qcs404-evb.dts deleted file mode 100644 index 07bf7dd0b32f..000000000000 --- a/arch/arm/dts/qcs404-evb.dts +++ /dev/null @@ -1,390 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Qualcomm QCS404 based evaluation board device tree source - * - * (C) Copyright 2022 Sumit Garg sumit.garg@linaro.org - */ - -/dts-v1/; - -#include "skeleton64.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/clock/qcom,gcc-qcs404.h> - -/ { - model = "Qualcomm Technologies, Inc. QCS404 EVB"; - compatible = "qcom,qcs404-evb", "qcom,qcs404"; - #address-cells = <0x2>; - #size-cells = <0x2>; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - aliases { - serial0 = &debug_uart; - i2c0 = &blsp1_i2c0; - i2c1 = &blsp1_i2c1; - i2c2 = &blsp1_i2c2; - i2c3 = &blsp1_i2c3; - i2c4 = &blsp1_i2c4; - }; - - memory { - device_type = "memory"; - reg = <0 0x80000000 0 0x40000000>; - }; - - soc { - #address-cells = <0x1>; - #size-cells = <0x1>; - ranges = <0x0 0x0 0x0 0xffffffff>; - compatible = "simple-bus"; - - soc_gpios: pinctrl_north@1300000 { - compatible = "qcom,qcs404-pinctrl"; - reg = <0x1300000 0x200000>; - gpio-controller; - gpio-count = <120>; - gpio-bank-name="soc"; - #gpio-cells = <2>; - - blsp1_uart2: uart { - pins = "GPIO_17", "GPIO_18"; - function = "blsp_uart2"; - }; - - blsp1_i2c0_default: blsp1-i2c0-default { - pins = "GPIO_32", "GPIO_33"; - function = "blsp_i2c0"; - }; - - blsp1_i2c1_default: blsp1-i2c1-default { - pins = "GPIO_24", "GPIO_25"; - function = "blsp_i2c1"; - }; - - blsp1_i2c2_default: blsp1-i2c2-default { - sda { - pins = "GPIO_19"; - function = "blsp_i2c_sda_a2"; - }; - - scl { - pins = "GPIO_20"; - function = "blsp_i2c_scl_a2"; - }; - }; - - blsp1_i2c3_default: blsp1-i2c3-default { - pins = "GPIO_84", "GPIO_85"; - function = "blsp_i2c3"; - }; - - blsp1_i2c4_default: blsp1-i2c4-default { - pins = "GPIO_117", "GPIO_118"; - function = "blsp_i2c4"; - }; - - ethernet_defaults: ethernet-defaults { - int { - pins = "GPIO_61"; - function = "rgmii_int"; - bias-disable; - drive-strength = <2>; - }; - mdc { - pins = "GPIO_76"; - function = "rgmii_mdc"; - bias-pull-up; - }; - mdio { - pins = "GPIO_75"; - function = "rgmii_mdio"; - bias-pull-up; - }; - tx { - pins = "GPIO_67", "GPIO_66", "GPIO_65", "GPIO_64"; - function = "rgmii_tx"; - bias-pull-up; - drive-strength = <16>; - }; - rx { - pins = "GPIO_73", "GPIO_72", "GPIO_71", "GPIO_70"; - function = "rgmii_rx"; - bias-disable; - drive-strength = <2>; - }; - tx-ctl { - pins = "GPIO_68"; - function = "rgmii_ctl"; - bias-pull-up; - drive-strength = <16>; - }; - rx-ctl { - pins = "GPIO_74"; - function = "rgmii_ctl"; - bias-disable; - drive-strength = <2>; - }; - tx-ck { - pins = "GPIO_63"; - function = "rgmii_ck"; - bias-pull-up; - drive-strength = <16>; - }; - rx-ck { - pins = "GPIO_69"; - function = "rgmii_ck"; - bias-disable; - drive-strength = <2>; - }; - }; - }; - - blsp1_i2c0: i2c@78b5000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0x078b5000 0x600>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>; - clock-names = "iface", "core"; - pinctrl-names = "default"; - pinctrl-0 = <&blsp1_i2c0_default>; - #address-cells = <1>; - #size-cells = <0>; - }; - - blsp1_i2c1: i2c@78b6000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0x078b6000 0x600>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>; - clock-names = "iface", "core"; - pinctrl-names = "default"; - pinctrl-0 = <&blsp1_i2c1_default>; - #address-cells = <1>; - #size-cells = <0>; - }; - - blsp1_i2c2: i2c@78b7000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0x078b7000 0x600>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; - clock-names = "iface", "core"; - pinctrl-names = "default"; - pinctrl-0 = <&blsp1_i2c2_default>; - #address-cells = <1>; - #size-cells = <0>; - }; - - blsp1_i2c3: i2c@78b8000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0x078b8000 0x600>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; - clock-names = "iface", "core"; - pinctrl-names = "default"; - pinctrl-0 = <&blsp1_i2c3_default>; - #address-cells = <1>; - #size-cells = <0>; - }; - - blsp1_i2c4: i2c@78b9000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0x078b9000 0x600>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>; - clock-names = "iface", "core"; - pinctrl-names = "default"; - pinctrl-0 = <&blsp1_i2c4_default>; - #address-cells = <1>; - #size-cells = <0>; - }; - - gcc: clock-controller@1800000 { - compatible = "qcom,gcc-qcs404"; - reg = <0x1800000 0x80000>; - #address-cells = <0x1>; - #size-cells = <0x0>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - debug_uart: serial@78b1000 { - compatible = "qcom,msm-uartdm-v1.4"; - reg = <0x78b1000 0x200>; - clock = <&gcc GCC_BLSP1_UART2_APPS_CLK>, - <&gcc GCC_BLSP1_AHB_CLK>; - bit-rate = <0xFF>; - pinctrl-names = "uart"; - pinctrl-0 = <&blsp1_uart2>; - }; - - sdhci@7804000 { - compatible = "qcom,sdhci-msm-v5"; - reg = <0x7804000 0x1000 0x7805000 0x1000>; - clock = <&gcc GCC_SDCC1_APPS_CLK>, - <&gcc GCC_SDCC1_AHB_CLK>; - bus-width = <0x8>; - index = <0x0>; - non-removable; - mmc-ddr-1_8v; - mmc-hs400-1_8v; - }; - - usb3_phy: phy@78000 { - compatible = "qcom,usb-ss-28nm-phy"; - #phy-cells = <0>; - reg = <0x78000 0x400>; - clocks = <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, - <&gcc GCC_USB3_PHY_PIPE_CLK>; - clock-names = "ahb", "pipe"; - resets = <&gcc GCC_USB3_PHY_BCR>, - <&gcc GCC_USB3PHY_PHY_BCR>; - reset-names = "com", "phy"; - }; - - usb2_phy_prim: phy@7a000 { - compatible = "qcom,usb-hs-28nm-femtophy"; - #phy-cells = <0>; - reg = <0x7a000 0x200>; - clocks = <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, - <&gcc GCC_USB2A_PHY_SLEEP_CLK>; - clock-names = "ahb", "sleep"; - resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>, - <&gcc GCC_USB2A_PHY_BCR>; - reset-names = "phy", "por"; - }; - - usb2_phy_sec: phy@7c000 { - compatible = "qcom,usb-hs-28nm-femtophy"; - #phy-cells = <0>; - reg = <0x7c000 0x200>; - clocks = <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, - <&gcc GCC_USB2A_PHY_SLEEP_CLK>; - clock-names = "ahb", "sleep"; - resets = <&gcc GCC_QUSB2_PHY_BCR>, - <&gcc GCC_USB2_HS_PHY_ONLY_BCR>; - reset-names = "phy", "por"; - }; - - usb3: usb@7678800 { - compatible = "qcom,dwc3"; - reg = <0x7678800 0x400>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - clocks = <&gcc GCC_USB30_MASTER_CLK>, - <&gcc GCC_SYS_NOC_USB3_CLK>, - <&gcc GCC_USB30_SLEEP_CLK>, - <&gcc GCC_USB30_MOCK_UTMI_CLK>; - clock-names = "core", "iface", "sleep", "mock_utmi"; - - dwc3@7580000 { - compatible = "snps,dwc3"; - reg = <0x7580000 0xcd00>; - phys = <&usb2_phy_prim>, <&usb3_phy>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,has-lpm-erratum; - snps,hird-threshold = /bits/ 8 <0x10>; - snps,usb3_lpm_capable; - maximum-speed = "super-speed"; - }; - }; - - usb2: usb@79b8800 { - compatible = "qcom,dwc3"; - reg = <0x79b8800 0x400>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>, - <&gcc GCC_PCNOC_USB2_CLK>, - <&gcc GCC_USB_HS_INACTIVITY_TIMERS_CLK>, - <&gcc GCC_USB20_MOCK_UTMI_CLK>; - clock-names = "core", "iface", "sleep", "mock_utmi"; - - dwc3@78c0000 { - compatible = "snps,dwc3"; - reg = <0x78c0000 0xcc00>; - phys = <&usb2_phy_sec>; - phy-names = "usb2-phy"; - dr_mode = "peripheral"; - snps,has-lpm-erratum; - snps,hird-threshold = /bits/ 8 <0x10>; - snps,usb3_lpm_capable; - maximum-speed = "high-speed"; - }; - }; - - ethernet: ethernet@7a80000 { - compatible = "qcom,qcs404-ethqos"; - reg = <0x07a80000 0x10000>, - <0x07a96000 0x100>; - reg-names = "stmmaceth", "rgmii"; - clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii"; - clocks = <&gcc GCC_ETH_AXI_CLK>, - <&gcc GCC_ETH_SLAVE_AHB_CLK>, - <&gcc GCC_ETH_PTP_CLK>, - <&gcc GCC_ETH_RGMII_CLK>; - - resets = <&gcc GCC_EMAC_BCR>; - reset-names = "emac"; - - snps,tso; - rx-fifo-depth = <4096>; - tx-fifo-depth = <4096>; - - snps,reset-gpio = <&soc_gpios 60 GPIO_ACTIVE_LOW>; - snps,reset-active-low; - snps,reset-delays-us = <0 10000 10000>; - - pinctrl-names = "default"; - pinctrl-0 = <&ethernet_defaults>; - - phy-handle = <&phy1>; - phy-mode = "rgmii"; - max-speed = <1000>; - - mdio { - #address-cells = <0x1>; - #size-cells = <0x0>; - compatible = "snps,dwmac-mdio"; - phy1: phy@3 { - compatible = "ethernet-phy-ieee802.3-c22"; - device_type = "ethernet-phy"; - reg = <0x3>; - }; - }; - }; - - spmi@200f000 { - compatible = "qcom,spmi-pmic-arb"; - reg = <0x200f000 0x001000>, - <0x2400000 0x800000>, - <0x2c00000 0x800000>; - reg-names = "core", "chnls", "obsrvr"; - #address-cells = <0x1>; - #size-cells = <0x1>; - - pms405_0: pms405@0 { - compatible = "qcom,spmi-pmic"; - reg = <0x0 0x1>; - #address-cells = <0x1>; - #size-cells = <0x1>; - - pms405_gpios: pms405_gpios@c000 { - compatible = "qcom,pms405-gpio"; - reg = <0xc000 0x400>; - gpio-controller; - gpio-ranges = <&pms405_gpios 0 0 12>; - #gpio-cells = <2>; - }; - }; - }; - }; -}; - -#include "qcs404-evb-uboot.dtsi" diff --git a/arch/arm/dts/qcs404-evb.dtsi b/arch/arm/dts/qcs404-evb.dtsi new file mode 100644 index 000000000000..10655401528e --- /dev/null +++ b/arch/arm/dts/qcs404-evb.dtsi @@ -0,0 +1,389 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018, Linaro Limited + */ + +#include <dt-bindings/gpio/gpio.h> +#include "qcs404.dtsi" +#include "pms405.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> + +/ { + aliases { + serial0 = &blsp1_uart2; + serial1 = &blsp1_uart3; + }; + + chosen { + stdout-path = "serial0"; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + }; + + vdd_ch0_3p3: + vdd_esmps3_3p3: vdd-esmps3-3p3-regulator { + compatible = "regulator-fixed"; + regulator-name = "eSMPS3_3P3"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + usb3_vbus_reg: regulator-usb3-vbus { + compatible = "regulator-fixed"; + regulator-name = "VBUS_BOOST_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pms405_gpios 3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_vbus_boost_pin>; + vin-supply = <&vph_pwr>; + enable-active-high; + + /* TODO: Drop this when introducing role switching */ + regulator-always-on; + }; +}; + +&blsp1_uart3 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&vreg_l6_1p8>; + vddxo-supply = <&vreg_l5_1p8>; + vddrf-supply = <&vreg_l1_1p3>; + vddch0-supply = <&vdd_ch0_3p3>; + + local-bd-address = [ 02 00 00 00 5a ad ]; + + max-speed = <3200000>; + }; +}; + +&blsp1_dma { + qcom,controlled-remotely; +}; + +&blsp2_dma { + qcom,controlled-remotely; +}; + +&gcc { + protected-clocks = <GCC_BIMC_CDSP_CLK>, + <GCC_CDSP_CFG_AHB_CLK>, + <GCC_CDSP_BIMC_CLK_SRC>, + <GCC_CDSP_TBU_CLK>, + <141>, /* GCC_WCSS_Q6_AHB_CLK */ + <142>; /* GCC_WCSS_Q6_AXIM_CLK */ +}; + +&pms405_spmi_regulators { + vdd_s3-supply = <&vph_pwr>; + + pms405_s3: s3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vdd_apc"; + regulator-initial-mode = <1>; + regulator-min-microvolt = <1048000>; + regulator-max-microvolt = <1384000>; + }; +}; + +&pcie { + status = "okay"; + + perst-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&perst_state>; +}; + +&pcie_phy { + status = "okay"; + + vdda-vp-supply = <&vreg_l3_1p05>; + vdda-vph-supply = <&vreg_l5_1p8>; +}; + +&remoteproc_adsp { + status = "okay"; +}; + +&remoteproc_cdsp { + status = "okay"; +}; + +&remoteproc_wcss { + status = "okay"; +}; + +&rpm_requests { + regulators { + compatible = "qcom,rpm-pms405-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_l1_l2-supply = <&vreg_s5_1p35>; + vdd_l3_l8-supply = <&vreg_s5_1p35>; + vdd_l4-supply = <&vreg_s5_1p35>; + vdd_l5_l6-supply = <&vreg_s4_1p8>; + vdd_l7-supply = <&vph_pwr>; + vdd_l9-supply = <&vreg_s5_1p35>; + vdd_l10_l11_l12_l13-supply = <&vph_pwr>; + + vreg_s4_1p8: s4 { + regulator-min-microvolt = <1728000>; + regulator-max-microvolt = <1920000>; + }; + + vreg_s5_1p35: s5 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_l1_1p3: l1 { + regulator-min-microvolt = <1240000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_l2_1p275: l2 { + regulator-min-microvolt = <1048000>; + regulator-max-microvolt = <1280000>; + }; + + vreg_l3_1p05: l3 { + regulator-min-microvolt = <1048000>; + regulator-max-microvolt = <1160000>; + }; + + vreg_l4_1p2: l4 { + regulator-min-microvolt = <1144000>; + regulator-max-microvolt = <1256000>; + }; + + vreg_l5_1p8: l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l6_1p8: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vreg_l7_1p8: l7 { + regulator-min-microvolt = <1616000>; + regulator-max-microvolt = <3000000>; + }; + + vreg_l8_1p2: l8 { + regulator-min-microvolt = <1136000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_l10_3p3: l10 { + regulator-min-microvolt = <2936000>; + regulator-max-microvolt = <3088000>; + }; + + vreg_l11_sdc2: l11 { + regulator-min-microvolt = <2696000>; + regulator-max-microvolt = <3304000>; + }; + + vreg_l12_3p3: l12 { + regulator-min-microvolt = <3050000>; + regulator-max-microvolt = <3300000>; + }; + + vreg_l13_3p3: l13 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + }; + }; +}; + +&sdcc1 { + status = "okay"; + + supports-cqe; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + bus-width = <8>; + non-removable; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; +}; + +&tlmm { + perst_state: perst-state { + pins = "gpio43"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + output-low; + }; + + sdc1_on: sdc1-on-state { + clk-pins { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd-pins { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data-pins { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + }; + + rclk-pins { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off-state { + clk-pins { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd-pins { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data-pins { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + rclk-pins { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + usb3_id_pin: usb3-id-state { + pins = "gpio116"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; +}; + +&pms405_gpios { + usb_vbus_boost_pin: usb-vbus-boost-state { + pinconf { + pins = "gpio3"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + power-source = <1>; + }; + }; + usb3_vbus_pin: usb3-vbus-state { + pinconf { + pins = "gpio12"; + function = PMIC_GPIO_FUNC_NORMAL; + input-enable; + bias-pull-down; + power-source = <1>; + }; + }; +}; + +&usb2 { + status = "okay"; +}; + +&usb2_phy_sec { + vdd-supply = <&vreg_l4_1p2>; + vdda1p8-supply = <&vreg_l5_1p8>; + vdda3p3-supply = <&vreg_l12_3p3>; + status = "okay"; +}; + +&usb3 { + status = "okay"; + +}; + +&usb3_dwc3 { + dr_mode = "host"; +}; + +&usb2_phy_prim { + vdd-supply = <&vreg_l4_1p2>; + vdda1p8-supply = <&vreg_l5_1p8>; + vdda3p3-supply = <&vreg_l12_3p3>; + status = "okay"; +}; + +&usb3_phy { + vdd-supply = <&vreg_l3_1p05>; + vdda1p8-supply = <&vreg_l5_1p8>; + status = "okay"; +}; + +&wifi { + status = "okay"; + vdd-0.8-cx-mx-supply = <&vreg_l2_1p275>; + vdd-1.8-xo-supply = <&vreg_l5_1p8>; + vdd-1.3-rfa-supply = <&vreg_l1_1p3>; +}; + +/* PINCTRL - additions to nodes defined in qcs404.dtsi */ + +&blsp1_uart2_default { + rx-pins { + drive-strength = <2>; + bias-disable; + }; + + tx-pins { + drive-strength = <2>; + bias-disable; + }; +}; + +&blsp1_uart3_default { + cts-pins { + bias-disable; + }; + + rts-tx-pins { + drive-strength = <2>; + bias-disable; + }; + + rx-pins { + bias-pull-up; + }; +}; diff --git a/arch/arm/dts/qcs404.dtsi b/arch/arm/dts/qcs404.dtsi new file mode 100644 index 000000000000..2721f32dfb71 --- /dev/null +++ b/arch/arm/dts/qcs404.dtsi @@ -0,0 +1,1829 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,gcc-qcs404.h> +#include <dt-bindings/clock/qcom,turingcc-qcs404.h> +#include <dt-bindings/clock/qcom,rpmcc.h> +#include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + next-level-cache = <&L2_0>; + #cooling-cells = <2>; + clocks = <&apcs_glb>; + operating-points-v2 = <&cpu_opp_table>; + power-domains = <&cpr>; + power-domain-names = "cpr"; + }; + + CPU1: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + next-level-cache = <&L2_0>; + #cooling-cells = <2>; + clocks = <&apcs_glb>; + operating-points-v2 = <&cpu_opp_table>; + power-domains = <&cpr>; + power-domain-names = "cpr"; + }; + + CPU2: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x102>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + next-level-cache = <&L2_0>; + #cooling-cells = <2>; + clocks = <&apcs_glb>; + operating-points-v2 = <&cpu_opp_table>; + power-domains = <&cpr>; + power-domain-names = "cpr"; + }; + + CPU3: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x103>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + next-level-cache = <&L2_0>; + #cooling-cells = <2>; + clocks = <&apcs_glb>; + operating-points-v2 = <&cpu_opp_table>; + power-domains = <&cpr>; + power-domain-names = "cpr"; + }; + + L2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + cache-unified; + }; + + idle-states { + entry-method = "psci"; + + CPU_SLEEP_0: cpu-sleep-0 { + compatible = "arm,idle-state"; + idle-state-name = "standalone-power-collapse"; + arm,psci-suspend-param = <0x40000003>; + entry-latency-us = <125>; + exit-latency-us = <180>; + min-residency-us = <595>; + local-timer-stop; + }; + }; + }; + + cpu_opp_table: opp-table-cpu { + compatible = "operating-points-v2-kryo-cpu"; + opp-shared; + + opp-1094400000 { + opp-hz = /bits/ 64 <1094400000>; + required-opps = <&cpr_opp1>; + }; + opp-1248000000 { + opp-hz = /bits/ 64 <1248000000>; + required-opps = <&cpr_opp2>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + required-opps = <&cpr_opp3>; + }; + }; + + cpr_opp_table: opp-table-cpr { + compatible = "operating-points-v2-qcom-level"; + + cpr_opp1: opp1 { + opp-level = <1>; + qcom,opp-fuse-level = <1>; + }; + cpr_opp2: opp2 { + opp-level = <2>; + qcom,opp-fuse-level = <2>; + }; + cpr_opp3: opp3 { + opp-level = <3>; + qcom,opp-fuse-level = <3>; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-qcs404", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0 0x80000000 0 0>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + rpm: remoteproc { + compatible = "qcom,qcs404-rpm-proc", "qcom,rpm-proc"; + + glink-edge { + compatible = "qcom,glink-rpm"; + + interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; + qcom,rpm-msg-ram = <&rpm_msg_ram>; + mboxes = <&apcs_glb 0>; + + rpm_requests: rpm-requests { + compatible = "qcom,rpm-qcs404"; + qcom,glink-channels = "rpm_requests"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-qcs404", "qcom,rpmcc"; + #clock-cells = <1>; + clocks = <&xo_board>; + clock-names = "xo"; + }; + + rpmpd: power-controller { + compatible = "qcom,qcs404-rpmpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmpd_opp_table>; + + rpmpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmpd_opp_ret: opp1 { + opp-level = <16>; + }; + + rpmpd_opp_ret_plus: opp2 { + opp-level = <32>; + }; + + rpmpd_opp_min_svs: opp3 { + opp-level = <48>; + }; + + rpmpd_opp_low_svs: opp4 { + opp-level = <64>; + }; + + rpmpd_opp_svs: opp5 { + opp-level = <128>; + }; + + rpmpd_opp_svs_plus: opp6 { + opp-level = <192>; + }; + + rpmpd_opp_nom: opp7 { + opp-level = <256>; + }; + + rpmpd_opp_nom_plus: opp8 { + opp-level = <320>; + }; + + rpmpd_opp_turbo: opp9 { + opp-level = <384>; + }; + + rpmpd_opp_turbo_no_cpr: opp10 { + opp-level = <416>; + }; + + rpmpd_opp_turbo_plus: opp11 { + opp-level = <512>; + }; + }; + }; + }; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + tz_apps_mem: memory@85900000 { + reg = <0 0x85900000 0 0x500000>; + no-map; + }; + + xbl_mem: memory@85e00000 { + reg = <0 0x85e00000 0 0x100000>; + no-map; + }; + + smem_region: memory@85f00000 { + reg = <0 0x85f00000 0 0x200000>; + no-map; + }; + + tz_mem: memory@86100000 { + reg = <0 0x86100000 0 0x300000>; + no-map; + }; + + wlan_fw_mem: memory@86400000 { + reg = <0 0x86400000 0 0x1100000>; + no-map; + }; + + adsp_fw_mem: memory@87500000 { + reg = <0 0x87500000 0 0x1a00000>; + no-map; + }; + + cdsp_fw_mem: memory@88f00000 { + reg = <0 0x88f00000 0 0x600000>; + no-map; + }; + + wlan_msa_mem: memory@89500000 { + reg = <0 0x89500000 0 0x100000>; + no-map; + }; + + uefi_mem: memory@9f800000 { + reg = <0 0x9f800000 0 0x800000>; + no-map; + }; + }; + + smem { + compatible = "qcom,smem"; + + memory-region = <&smem_region>; + qcom,rpm-msg-ram = <&rpm_msg_ram>; + + hwlocks = <&tcsr_mutex 3>; + }; + + soc: soc@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + compatible = "simple-bus"; + + turingcc: clock-controller@800000 { + compatible = "qcom,qcs404-turingcc"; + reg = <0x00800000 0x30000>; + clocks = <&gcc GCC_CDSP_CFG_AHB_CLK>; + + #clock-cells = <1>; + #reset-cells = <1>; + + status = "disabled"; + }; + + rpm_msg_ram: sram@60000 { + compatible = "qcom,rpm-msg-ram"; + reg = <0x00060000 0x6000>; + }; + + usb3_phy: phy@78000 { + compatible = "qcom,usb-ss-28nm-phy"; + reg = <0x00078000 0x400>; + #phy-cells = <0>; + clocks = <&rpmcc RPM_SMD_LN_BB_CLK>, + <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, + <&gcc GCC_USB3_PHY_PIPE_CLK>; + clock-names = "ref", "ahb", "pipe"; + resets = <&gcc GCC_USB3_PHY_BCR>, + <&gcc GCC_USB3PHY_PHY_BCR>; + reset-names = "com", "phy"; + status = "disabled"; + }; + + usb2_phy_prim: phy@7a000 { + compatible = "qcom,usb-hs-28nm-femtophy"; + reg = <0x0007a000 0x200>; + #phy-cells = <0>; + clocks = <&rpmcc RPM_SMD_LN_BB_CLK>, + <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, + <&gcc GCC_USB2A_PHY_SLEEP_CLK>; + clock-names = "ref", "ahb", "sleep"; + resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>, + <&gcc GCC_USB2A_PHY_BCR>; + reset-names = "phy", "por"; + status = "disabled"; + }; + + usb2_phy_sec: phy@7c000 { + compatible = "qcom,usb-hs-28nm-femtophy"; + reg = <0x0007c000 0x200>; + #phy-cells = <0>; + clocks = <&rpmcc RPM_SMD_LN_BB_CLK>, + <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, + <&gcc GCC_USB2A_PHY_SLEEP_CLK>; + clock-names = "ref", "ahb", "sleep"; + resets = <&gcc GCC_QUSB2_PHY_BCR>, + <&gcc GCC_USB2_HS_PHY_ONLY_BCR>; + reset-names = "phy", "por"; + status = "disabled"; + }; + + qfprom: qfprom@a4000 { + compatible = "qcom,qcs404-qfprom", "qcom,qfprom"; + reg = <0x000a4000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + cpr_efuse_speedbin: speedbin@13c { + reg = <0x13c 0x4>; + bits = <2 3>; + }; + + tsens_s0_p1: s0-p1@1f8 { + reg = <0x1f8 0x1>; + bits = <0 6>; + }; + + tsens_s0_p2: s0-p2@1f8 { + reg = <0x1f8 0x2>; + bits = <6 6>; + }; + + tsens_s1_p1: s1-p1@1f9 { + reg = <0x1f9 0x2>; + bits = <4 6>; + }; + + tsens_s1_p2: s1-p2@1fa { + reg = <0x1fa 0x1>; + bits = <2 6>; + }; + + tsens_s2_p1: s2-p1@1fb { + reg = <0x1fb 0x1>; + bits = <0 6>; + }; + + tsens_s2_p2: s2-p2@1fb { + reg = <0x1fb 0x2>; + bits = <6 6>; + }; + + tsens_s3_p1: s3-p1@1fc { + reg = <0x1fc 0x2>; + bits = <4 6>; + }; + + tsens_s3_p2: s3-p2@1fd { + reg = <0x1fd 0x1>; + bits = <2 6>; + }; + + tsens_s4_p1: s4-p1@1fe { + reg = <0x1fe 0x1>; + bits = <0 6>; + }; + + tsens_s4_p2: s4-p2@1fe { + reg = <0x1fe 0x2>; + bits = <6 6>; + }; + + tsens_s5_p1: s5-p1@200 { + reg = <0x200 0x1>; + bits = <0 6>; + }; + + tsens_s5_p2: s5-p2@200 { + reg = <0x200 0x2>; + bits = <6 6>; + }; + + tsens_s6_p1: s6-p1@201 { + reg = <0x201 0x2>; + bits = <4 6>; + }; + + tsens_s6_p2: s6-p2@202 { + reg = <0x202 0x1>; + bits = <2 6>; + }; + + tsens_s7_p1: s7-p1@203 { + reg = <0x203 0x1>; + bits = <0 6>; + }; + + tsens_s7_p2: s7-p2@203 { + reg = <0x203 0x2>; + bits = <6 6>; + }; + + tsens_s8_p1: s8-p1@204 { + reg = <0x204 0x2>; + bits = <4 6>; + }; + + tsens_s8_p2: s8-p2@205 { + reg = <0x205 0x1>; + bits = <2 6>; + }; + + tsens_s9_p1: s9-p1@206 { + reg = <0x206 0x1>; + bits = <0 6>; + }; + + tsens_s9_p2: s9-p2@206 { + reg = <0x206 0x2>; + bits = <6 6>; + }; + + tsens_mode: mode@208 { + reg = <0x208 1>; + bits = <0 3>; + }; + + tsens_base1: base1@208 { + reg = <0x208 2>; + bits = <3 8>; + }; + + tsens_base2: base2@208 { + reg = <0x209 2>; + bits = <3 8>; + }; + + cpr_efuse_quot_offset1: qoffset1@231 { + reg = <0x231 0x4>; + bits = <4 7>; + }; + cpr_efuse_quot_offset2: qoffset2@232 { + reg = <0x232 0x4>; + bits = <3 7>; + }; + cpr_efuse_quot_offset3: qoffset3@233 { + reg = <0x233 0x4>; + bits = <2 7>; + }; + cpr_efuse_init_voltage1: ivoltage1@229 { + reg = <0x229 0x4>; + bits = <4 6>; + }; + cpr_efuse_init_voltage2: ivoltage2@22a { + reg = <0x22a 0x4>; + bits = <2 6>; + }; + cpr_efuse_init_voltage3: ivoltage3@22b { + reg = <0x22b 0x4>; + bits = <0 6>; + }; + cpr_efuse_quot1: quot1@22b { + reg = <0x22b 0x4>; + bits = <6 12>; + }; + cpr_efuse_quot2: quot2@22d { + reg = <0x22d 0x4>; + bits = <2 12>; + }; + cpr_efuse_quot3: quot3@230 { + reg = <0x230 0x4>; + bits = <0 12>; + }; + cpr_efuse_ring1: ring1@228 { + reg = <0x228 0x4>; + bits = <0 3>; + }; + cpr_efuse_ring2: ring2@228 { + reg = <0x228 0x4>; + bits = <4 3>; + }; + cpr_efuse_ring3: ring3@229 { + reg = <0x229 0x4>; + bits = <0 3>; + }; + cpr_efuse_revision: revision@218 { + reg = <0x218 0x4>; + bits = <3 3>; + }; + }; + + rng: rng@e3000 { + compatible = "qcom,prng-ee"; + reg = <0x000e3000 0x1000>; + clocks = <&gcc GCC_PRNG_AHB_CLK>; + clock-names = "core"; + }; + + bimc: interconnect@400000 { + reg = <0x00400000 0x80000>; + compatible = "qcom,qcs404-bimc"; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_BIMC_CLK>, + <&rpmcc RPM_SMD_BIMC_A_CLK>; + }; + + tsens: thermal-sensor@4a9000 { + compatible = "qcom,qcs404-tsens", "qcom,tsens-v1"; + reg = <0x004a9000 0x1000>, /* TM */ + <0x004a8000 0x1000>; /* SROT */ + nvmem-cells = <&tsens_mode>, + <&tsens_base1>, <&tsens_base2>, + <&tsens_s0_p1>, <&tsens_s0_p2>, + <&tsens_s1_p1>, <&tsens_s1_p2>, + <&tsens_s2_p1>, <&tsens_s2_p2>, + <&tsens_s3_p1>, <&tsens_s3_p2>, + <&tsens_s4_p1>, <&tsens_s4_p2>, + <&tsens_s5_p1>, <&tsens_s5_p2>, + <&tsens_s6_p1>, <&tsens_s6_p2>, + <&tsens_s7_p1>, <&tsens_s7_p2>, + <&tsens_s8_p1>, <&tsens_s8_p2>, + <&tsens_s9_p1>, <&tsens_s9_p2>; + nvmem-cell-names = "mode", + "base1", "base2", + "s0_p1", "s0_p2", + "s1_p1", "s1_p2", + "s2_p1", "s2_p2", + "s3_p1", "s3_p2", + "s4_p1", "s4_p2", + "s5_p1", "s5_p2", + "s6_p1", "s6_p2", + "s7_p1", "s7_p2", + "s8_p1", "s8_p2", + "s9_p1", "s9_p2"; + #qcom,sensors = <10>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow"; + #thermal-sensor-cells = <1>; + }; + + pcnoc: interconnect@500000 { + reg = <0x00500000 0x15080>; + compatible = "qcom,qcs404-pcnoc"; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_PNOC_CLK>, + <&rpmcc RPM_SMD_PNOC_A_CLK>; + }; + + snoc: interconnect@580000 { + reg = <0x00580000 0x23080>; + compatible = "qcom,qcs404-snoc"; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_SNOC_CLK>, + <&rpmcc RPM_SMD_SNOC_A_CLK>; + }; + + remoteproc_cdsp: remoteproc@b00000 { + compatible = "qcom,qcs404-cdsp-pas"; + reg = <0x00b00000 0x4040>; + + interrupts-extended = <&intc GIC_SPI 229 IRQ_TYPE_EDGE_RISING>, + <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&xo_board>; + clock-names = "xo"; + + /* + * If the node was using the PIL binding, then include properties: + * clocks = <&xo_board>, + * <&gcc GCC_CDSP_CFG_AHB_CLK>, + * <&gcc GCC_CDSP_TBU_CLK>, + * <&gcc GCC_BIMC_CDSP_CLK>, + * <&turingcc TURING_WRAPPER_AON_CLK>, + * <&turingcc TURING_Q6SS_AHBS_AON_CLK>, + * <&turingcc TURING_Q6SS_AHBM_AON_CLK>, + * <&turingcc TURING_Q6SS_Q6_AXIM_CLK>; + * clock-names = "xo", + * "sway", + * "tbu", + * "bimc", + * "ahb_aon", + * "q6ss_slave", + * "q6ss_master", + * "q6_axim"; + * resets = <&gcc GCC_CDSP_RESTART>; + * reset-names = "restart"; + * qcom,halt-regs = <&tcsr 0x19004>; + */ + + memory-region = <&cdsp_fw_mem>; + + qcom,smem-states = <&cdsp_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + status = "disabled"; + + glink-edge { + interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>; + + qcom,remote-pid = <5>; + mboxes = <&apcs_glb 12>; + + label = "cdsp"; + }; + }; + + usb3: usb@7678800 { + compatible = "qcom,qcs404-dwc3", "qcom,dwc3"; + reg = <0x07678800 0x400>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + clocks = <&gcc GCC_USB30_MASTER_CLK>, + <&gcc GCC_SYS_NOC_USB3_CLK>, + <&gcc GCC_USB30_SLEEP_CLK>, + <&gcc GCC_USB30_MOCK_UTMI_CLK>; + clock-names = "core", "iface", "sleep", "mock_utmi"; + assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + status = "disabled"; + + usb3_dwc3: usb@7580000 { + compatible = "snps,dwc3"; + reg = <0x07580000 0xcd00>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usb2_phy_prim>, <&usb3_phy>; + phy-names = "usb2-phy", "usb3-phy"; + snps,has-lpm-erratum; + snps,hird-threshold = /bits/ 8 <0x10>; + snps,usb3_lpm_capable; + dr_mode = "otg"; + }; + }; + + usb2: usb@79b8800 { + compatible = "qcom,qcs404-dwc3", "qcom,dwc3"; + reg = <0x079b8800 0x400>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_PCNOC_USB2_CLK>, + <&gcc GCC_USB_HS_INACTIVITY_TIMERS_CLK>, + <&gcc GCC_USB20_MOCK_UTMI_CLK>; + clock-names = "core", "iface", "sleep", "mock_utmi"; + assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>, + <&gcc GCC_USB_HS_SYSTEM_CLK>; + assigned-clock-rates = <19200000>, <133333333>; + status = "disabled"; + + usb@78c0000 { + compatible = "snps,dwc3"; + reg = <0x078c0000 0xcc00>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usb2_phy_sec>; + phy-names = "usb2-phy"; + snps,has-lpm-erratum; + snps,hird-threshold = /bits/ 8 <0x10>; + snps,usb3_lpm_capable; + dr_mode = "peripheral"; + }; + }; + + tlmm: pinctrl@1000000 { + compatible = "qcom,qcs404-pinctrl"; + reg = <0x01000000 0x200000>, + <0x01300000 0x200000>, + <0x07b00000 0x200000>; + reg-names = "south", "north", "east"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&tlmm 0 0 120>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + blsp1_i2c0_default: blsp1-i2c0-default-state { + pins = "gpio32", "gpio33"; + function = "blsp_i2c0"; + }; + + blsp1_i2c1_default: blsp1-i2c1-default-state { + pins = "gpio24", "gpio25"; + function = "blsp_i2c1"; + }; + + blsp1_i2c2_default: blsp1-i2c2-default-state { + sda-pins { + pins = "gpio19"; + function = "blsp_i2c_sda_a2"; + }; + + scl-pins { + pins = "gpio20"; + function = "blsp_i2c_scl_a2"; + }; + }; + + blsp1_i2c3_default: blsp1-i2c3-default-state { + pins = "gpio84", "gpio85"; + function = "blsp_i2c3"; + }; + + blsp1_i2c4_default: blsp1-i2c4-default-state { + pins = "gpio117", "gpio118"; + function = "blsp_i2c4"; + }; + + blsp1_uart0_default: blsp1-uart0-default-state { + pins = "gpio30", "gpio31", "gpio32", "gpio33"; + function = "blsp_uart0"; + }; + + blsp1_uart1_default: blsp1-uart1-default-state { + pins = "gpio22", "gpio23"; + function = "blsp_uart1"; + }; + + blsp1_uart2_default: blsp1-uart2-default-state { + rx-pins { + pins = "gpio18"; + function = "blsp_uart_rx_a2"; + }; + + tx-pins { + pins = "gpio17"; + function = "blsp_uart_tx_a2"; + }; + }; + + blsp1_uart3_default: blsp1-uart3-default-state { + cts-pins { + pins = "gpio84"; + function = "blsp_uart3"; + }; + + rts-tx-pins { + pins = "gpio85", "gpio82"; + function = "blsp_uart3"; + }; + + rx-pins { + pins = "gpio83"; + function = "blsp_uart3"; + }; + }; + + blsp2_i2c0_default: blsp2-i2c0-default-state { + pins = "gpio28", "gpio29"; + function = "blsp_i2c5"; + }; + + blsp1_spi0_default: blsp1-spi0-default-state { + pins = "gpio30", "gpio31", "gpio32", "gpio33"; + function = "blsp_spi0"; + }; + + blsp1_spi1_default: blsp1-spi1-default-state { + mosi-pins { + pins = "gpio22"; + function = "blsp_spi_mosi_a1"; + }; + + miso-pins { + pins = "gpio23"; + function = "blsp_spi_miso_a1"; + }; + + cs-n-pins { + pins = "gpio24"; + function = "blsp_spi_cs_n_a1"; + }; + + clk-pins { + pins = "gpio25"; + function = "blsp_spi_clk_a1"; + }; + }; + + blsp1_spi2_default: blsp1-spi2-default-state { + pins = "gpio17", "gpio18", "gpio19", "gpio20"; + function = "blsp_spi2"; + }; + + blsp1_spi3_default: blsp1-spi3-default-state { + pins = "gpio82", "gpio83", "gpio84", "gpio85"; + function = "blsp_spi3"; + }; + + blsp1_spi4_default: blsp1-spi4-default-state { + pins = "gpio37", "gpio38", "gpio117", "gpio118"; + function = "blsp_spi4"; + }; + + blsp2_spi0_default: blsp2-spi0-default-state { + pins = "gpio26", "gpio27", "gpio28", "gpio29"; + function = "blsp_spi5"; + }; + + blsp2_uart0_default: blsp2-uart0-default-state { + pins = "gpio26", "gpio27", "gpio28", "gpio29"; + function = "blsp_uart5"; + }; + }; + + gcc: clock-controller@1800000 { + compatible = "qcom,gcc-qcs404"; + reg = <0x01800000 0x80000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + + clocks = <&xo_board>, + <&sleep_clk>, + <&pcie_phy>, + <0>, + <0>, + <0>; + + assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>; + assigned-clock-rates = <19200000>; + }; + + tcsr_mutex: hwlock@1905000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x01905000 0x20000>; + #hwlock-cells = <1>; + }; + + tcsr: syscon@1937000 { + compatible = "qcom,qcs404-tcsr", "syscon"; + reg = <0x01937000 0x25000>; + }; + + sram@290000 { + compatible = "qcom,rpm-stats"; + reg = <0x00290000 0x10000>; + }; + + spmi_bus: spmi@200f000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0200f000 0x001000>, + <0x02400000 0x800000>, + <0x02c00000 0x800000>, + <0x03800000 0x200000>, + <0x0200a000 0x002100>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + }; + + remoteproc_wcss: remoteproc@7400000 { + compatible = "qcom,qcs404-wcss-pas"; + reg = <0x07400000 0x4040>; + + interrupts-extended = <&intc GIC_SPI 153 IRQ_TYPE_EDGE_RISING>, + <&wcss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&wcss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&wcss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&wcss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&xo_board>; + clock-names = "xo"; + + memory-region = <&wlan_fw_mem>; + + qcom,smem-states = <&wcss_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + status = "disabled"; + + glink-edge { + interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>; + + qcom,remote-pid = <1>; + mboxes = <&apcs_glb 16>; + + label = "wcss"; + }; + }; + + pcie_phy: phy@7786000 { + compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy"; + reg = <0x07786000 0xb8>; + + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; + resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>, + <&gcc GCC_PCIE_0_PIPE_ARES>; + reset-names = "phy", "pipe"; + + clock-output-names = "pcie_0_pipe_clk"; + #clock-cells = <0>; + #phy-cells = <0>; + + status = "disabled"; + }; + + sdcc1: mmc@7804000 { + compatible = "qcom,qcs404-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x07804000 0x1000>, <0x7805000 0x1000>; + reg-names = "hc", "cqhci"; + + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>, + <&xo_board>; + clock-names = "iface", "core", "xo"; + + status = "disabled"; + }; + + blsp1_dma: dma-controller@7884000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x07884000 0x25000>; + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + status = "okay"; + }; + + blsp1_uart0: serial@78af000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078af000 0x200>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART0_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 0>, <&blsp1_dma 1>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_uart0_default>; + status = "disabled"; + }; + + blsp1_uart1: serial@78b0000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078b0000 0x200>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 2>, <&blsp1_dma 3>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_uart1_default>; + status = "disabled"; + }; + + blsp1_uart2: serial@78b1000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078b1000 0x200>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 4>, <&blsp1_dma 5>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_uart2_default>; + status = "okay"; + }; + + ethernet: ethernet@7a80000 { + compatible = "qcom,qcs404-ethqos"; + reg = <0x07a80000 0x10000>, + <0x07a96000 0x100>; + reg-names = "stmmaceth", "rgmii"; + clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii"; + clocks = <&gcc GCC_ETH_AXI_CLK>, + <&gcc GCC_ETH_SLAVE_AHB_CLK>, + <&gcc GCC_ETH_PTP_CLK>, + <&gcc GCC_ETH_RGMII_CLK>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_lpi"; + + snps,tso; + rx-fifo-depth = <4096>; + tx-fifo-depth = <4096>; + + status = "disabled"; + }; + + wifi: wifi@a000000 { + compatible = "qcom,wcn3990-wifi"; + reg = <0xa000000 0x800000>; + reg-names = "membase"; + memory-region = <&wlan_msa_mem>; + interrupts = <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + blsp1_uart3: serial@78b2000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078b2000 0x200>; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_uart3_default>; + status = "disabled"; + }; + + blsp1_i2c0: i2c@78b5000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b5000 0x600>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_i2c0_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_spi0: spi@78b5000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x078b5000 0x600>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP0_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_spi0_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_i2c1: i2c@78b6000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b6000 0x600>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_i2c1_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_spi1: spi@78b6000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x078b6000 0x600>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_spi1_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_i2c2: i2c@78b7000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b7000 0x600>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_i2c2_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_spi2: spi@78b7000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x078b7000 0x600>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_spi2_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_i2c3: i2c@78b8000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b8000 0x600>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_i2c3_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_spi3: spi@78b8000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x078b8000 0x600>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_spi3_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_i2c4: i2c@78b9000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b9000 0x600>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_i2c4_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_spi4: spi@78b9000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x078b9000 0x600>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp1_spi4_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_dma: dma-controller@7ac4000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x07ac4000 0x17000>; + interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + status = "disabled"; + }; + + blsp2_uart0: serial@7aef000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x07aef000 0x200>; + interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_UART0_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp2_dma 0>, <&blsp2_dma 1>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp2_uart0_default>; + status = "disabled"; + }; + + blsp2_i2c0: i2c@7af5000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x07af5000 0x600>; + interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_QUP0_I2C_APPS_CLK>, + <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp2_i2c0_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_spi0: spi@7af5000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x07af5000 0x600>; + interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_QUP0_SPI_APPS_CLK>, + <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default"; + pinctrl-0 = <&blsp2_spi0_default>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + sram@8600000 { + compatible = "qcom,qcs404-imem", "syscon", "simple-mfd"; + reg = <0x08600000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0 0x08600000 0x1000>; + + pil-reloc@94c { + compatible = "qcom,pil-reloc-info"; + reg = <0x94c 0xc8>; + }; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x0b000000 0x1000>, + <0x0b002000 0x1000>; + }; + + apcs_glb: mailbox@b011000 { + compatible = "qcom,qcs404-apcs-apps-global", + "qcom,msm8916-apcs-kpss-global", "syscon"; + reg = <0x0b011000 0x1000>; + #mbox-cells = <1>; + clocks = <&apcs_hfpll>, <&gcc GCC_GPLL0_AO_OUT_MAIN>; + clock-names = "pll", "aux"; + #clock-cells = <0>; + }; + + apcs_hfpll: clock-controller@b016000 { + compatible = "qcom,hfpll"; + reg = <0x0b016000 0x30>; + #clock-cells = <0>; + clock-output-names = "apcs_hfpll"; + clocks = <&xo_board>; + clock-names = "xo"; + }; + + watchdog@b017000 { + compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt"; + reg = <0x0b017000 0x1000>; + clocks = <&sleep_clk>; + }; + + cpr: power-controller@b018000 { + compatible = "qcom,qcs404-cpr", "qcom,cpr"; + reg = <0x0b018000 0x1000>; + interrupts = <0 15 IRQ_TYPE_EDGE_RISING>; + clocks = <&xo_board>; + clock-names = "ref"; + vdd-apc-supply = <&pms405_s3>; + #power-domain-cells = <0>; + operating-points-v2 = <&cpr_opp_table>; + acc-syscon = <&tcsr>; + + nvmem-cells = <&cpr_efuse_quot_offset1>, + <&cpr_efuse_quot_offset2>, + <&cpr_efuse_quot_offset3>, + <&cpr_efuse_init_voltage1>, + <&cpr_efuse_init_voltage2>, + <&cpr_efuse_init_voltage3>, + <&cpr_efuse_quot1>, + <&cpr_efuse_quot2>, + <&cpr_efuse_quot3>, + <&cpr_efuse_ring1>, + <&cpr_efuse_ring2>, + <&cpr_efuse_ring3>, + <&cpr_efuse_revision>; + nvmem-cell-names = "cpr_quotient_offset1", + "cpr_quotient_offset2", + "cpr_quotient_offset3", + "cpr_init_voltage1", + "cpr_init_voltage2", + "cpr_init_voltage3", + "cpr_quotient1", + "cpr_quotient2", + "cpr_quotient3", + "cpr_ring_osc1", + "cpr_ring_osc2", + "cpr_ring_osc3", + "cpr_fuse_revision"; + }; + + timer@b120000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + clock-frequency = <19200000>; + + frame@b121000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + }; + + frame@b123000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b123000 0x1000>; + status = "disabled"; + }; + + frame@b124000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b124000 0x1000>; + status = "disabled"; + }; + + frame@b125000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b125000 0x1000>; + status = "disabled"; + }; + + frame@b126000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b126000 0x1000>; + status = "disabled"; + }; + + frame@b127000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xb127000 0x1000>; + status = "disabled"; + }; + + frame@b128000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b128000 0x1000>; + status = "disabled"; + }; + }; + + remoteproc_adsp: remoteproc@c700000 { + compatible = "qcom,qcs404-adsp-pas"; + reg = <0x0c700000 0x4040>; + + interrupts-extended = <&intc GIC_SPI 293 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&xo_board>; + clock-names = "xo"; + + memory-region = <&adsp_fw_mem>; + + qcom,smem-states = <&adsp_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + status = "disabled"; + + glink-edge { + interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>; + + qcom,remote-pid = <2>; + mboxes = <&apcs_glb 8>; + + label = "adsp"; + }; + }; + + pcie: pci@10000000 { + compatible = "qcom,pcie-qcs404"; + reg = <0x10000000 0xf1d>, + <0x10000f20 0xa8>, + <0x07780000 0x2000>, + <0x10001000 0x2000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0x0 0x00000000 0x10003000 0x0 0x00010000>, /* I/O */ + <0x82000000 0x0 0x10013000 0x10013000 0x0 0x007ed000>; /* memory */ + + interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_0_AUX_CLK>, + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_0_SLV_AXI_CLK>; + clock-names = "iface", "aux", "master_bus", "slave_bus"; + + resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>, + <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>, + <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>, + <&gcc GCC_PCIE_0_CORE_STICKY_ARES>, + <&gcc GCC_PCIE_0_BCR>, + <&gcc GCC_PCIE_0_AHB_ARES>; + reset-names = "axi_m", + "axi_s", + "axi_m_sticky", + "pipe_sticky", + "pwr", + "ahb"; + + phys = <&pcie_phy>; + phy-names = "pciephy"; + + status = "disabled"; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 0xff08>, + <GIC_PPI 3 0xff08>, + <GIC_PPI 4 0xff08>, + <GIC_PPI 1 0xff08>; + }; + + smp2p-adsp { + compatible = "qcom,smp2p"; + qcom,smem = <443>, <429>; + interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apcs_glb 10>; + qcom,local-pid = <0>; + qcom,remote-pid = <2>; + + adsp_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + adsp_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-cdsp { + compatible = "qcom,smp2p"; + qcom,smem = <94>, <432>; + interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apcs_glb 14>; + qcom,local-pid = <0>; + qcom,remote-pid = <5>; + + cdsp_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + cdsp_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-wcss { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apcs_glb 18>; + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + wcss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + wcss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + thermal-zones { + aoss-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 0>; + + trips { + aoss_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + q6-hvx-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 1>; + + trips { + q6_hvx_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + lpass-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 2>; + + trips { + lpass_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + wlan-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 3>; + + trips { + wlan_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + cluster-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 4>; + + trips { + cluster_alert0: trip-point0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cluster_alert1: trip-point1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cluster_crit: cluster-crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cluster_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 5>; + + trips { + cpu0_alert0: trip-point0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cpu0_alert1: trip-point1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu0_crit: cpu-crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu0_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 6>; + + trips { + cpu1_alert0: trip-point0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cpu1_alert1: trip-point1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu1_crit: cpu-crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu1_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu2-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 7>; + + trips { + cpu2_alert0: trip-point0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cpu2_alert1: trip-point1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu2_crit: cpu-crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu2_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu3-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 8>; + + trips { + cpu3_alert0: trip-point0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cpu3_alert1: trip-point1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu3_crit: cpu-crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu3_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + gpu-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 9>; + + trips { + gpu_alert0: trip-point0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + }; +};