Re: [U-Boot] [PATCH 2/8] net: zynq: Add clk framework support to zynq ethernet driver

On 4.1.2017 13:27, stefan.herbrechtsmeier@weidmueller.com wrote:

From: Stefan Herbrechtsmeier stefan.herbrechtsmeier@weidmueller.de

If available use the clock framework to set the tx clock rate of the zynq ethernet controller.

Signed-off-by: Stefan Herbrechtsmeier stefan.herbrechtsmeier@weidmueller.com

arch/arm/include/asm/arch-zynqmp/sys_proto.h | 5 ----- drivers/net/zynq_gem.c | 31 ++++++++++++++++++++++++++++ 2 files changed, 31 insertions(+), 5 deletions(-)

diff --git a/arch/arm/include/asm/arch-zynqmp/sys_proto.h b/arch/arm/include/asm/arch-zynqmp/sys_proto.h index 1db2bd6..bd633a6 100644 --- a/arch/arm/include/asm/arch-zynqmp/sys_proto.h +++ b/arch/arm/include/asm/arch-zynqmp/sys_proto.h @@ -8,11 +8,6 @@ #ifndef _ASM_ARCH_SYS_PROTO_H #define _ASM_ARCH_SYS_PROTO_H

-/* Setup clk for network */ -static inline void zynq_slcr_gem_clk_setup(u32 gem_id, unsigned long clk_rate) -{ -}

int zynq_slcr_get_mio_pin_status(const char *periph);

unsigned int zynqmp_get_silicon_version(void); diff --git a/drivers/net/zynq_gem.c b/drivers/net/zynq_gem.c index 9bfb89f..9118e49 100644 --- a/drivers/net/zynq_gem.c +++ b/drivers/net/zynq_gem.c @@ -9,6 +9,7 @@

• SPDX-License-Identifier: GPL-2.0+

*/

+#include <clk.h> #include <common.h> #include <dm.h> #include <net.h> @@ -180,6 +181,9 @@ struct zynq_gem_priv { struct phy_device *phydev; int phy_of_handle; struct mii_dev *bus; +#if defined(CONFIG_CLK) || defined(CONFIG_SPL_CLK)

• struct clk tx_clk;

+#endif };

static inline int mdio_wait(struct zynq_gem_regs *regs) @@ -364,6 +368,9 @@ static int zynq_gem_init(struct udevice *dev) u32 i, nwconfig; int ret; unsigned long clk_rate = 0; +#if defined(CONFIG_CLK) || defined(CONFIG_SPL_CLK)

• unsigned long clk_rate_rounded;

+#endif struct zynq_gem_priv *priv = dev_get_priv(dev); struct zynq_gem_regs *regs = priv->iobase; struct emac_bd *dummy_tx_bd = &priv->tx_bd[TX_FREE_DESC]; @@ -466,8 +473,22 @@ static int zynq_gem_init(struct udevice *dev) break; }

+#if defined(CONFIG_CLK) || defined(CONFIG_SPL_CLK)

• clk_rate_rounded = clk_set_rate(&priv->tx_clk, clk_rate);
• if (IS_ERR_VALUE(clk_rate_rounded)) {

• dev_err(dev, "failed to set tx clock rate\n");
  

• return clk_rate_rounded;
  

• }
• ret = clk_enable(&priv->tx_clk);
• if (ret && ret != -ENOSYS) {

• dev_err(dev, "failed to enable tx clock\n");
  

• return ret;
  

• }

+#else zynq_slcr_gem_clk_setup((ulong)priv->iobase != ZYNQ_GEM_BASEADDR0, clk_rate); +#endif

setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK | ZYNQ_GEM_NWCTRL_TXEN_MASK); @@ -678,6 +699,9 @@ static int zynq_gem_ofdata_to_platdata(struct udevice *dev) struct eth_pdata *pdata = dev_get_platdata(dev); struct zynq_gem_priv *priv = dev_get_priv(dev); const char *phy_mode; +#if defined(CONFIG_CLK) || defined(CONFIG_SPL_CLK)

• int ret;

+#endif

pdata->iobase = (phys_addr_t)dev_get_addr(dev); priv->iobase = (struct zynq_gem_regs *)pdata->iobase; @@ -699,6 +723,13 @@ static int zynq_gem_ofdata_to_platdata(struct udevice *dev) } priv->interface = pdata->phy_interface;

+#if defined(CONFIG_CLK) || defined(CONFIG_SPL_CLK)

• ret = clk_get_by_index(dev, 2, &priv->tx_clk);
• if (ret < 0) {

• dev_err(dev, "failed to get clock\n");
  

• return ret;
  

• }

+#endif

printf("ZYNQ GEM: %lx, phyaddr %x, interface %s\n", (ulong)priv->iobase, priv->phyaddr, phy_string_for_interface(priv->interface));

Can you please rebase it on the top of this? https://patchwork.ozlabs.org/patch/706419/

The reason why this patch was written in this way is that we don't have full zynqmp clk driver yet but we are using fixed clock where you can't run set_rate which fails.

The patch above will be merged soon that's why please rebase it on the top of it. Here is branch with this patch. http://git.denx.de/?p=u-boot/u-boot-microblaze.git;a=summary

Thanks, Michal