Because the introduction of the pinctrl and clk drivers and the device tree files, remove unneeded hard coded related code from the board file.
Signed-off-by: Wenyou Yang wenyou.yang@atmel.com ---
Changes in v2: None
board/atmel/at91sam9263ek/at91sam9263ek.c | 59 ------------------------------- 1 file changed, 59 deletions(-)
diff --git a/board/atmel/at91sam9263ek/at91sam9263ek.c b/board/atmel/at91sam9263ek/at91sam9263ek.c index e4e32f60ae..2aafafe35e 100644 --- a/board/atmel/at91sam9263ek/at91sam9263ek.c +++ b/board/atmel/at91sam9263ek/at91sam9263ek.c @@ -19,11 +19,6 @@ #include <asm/arch/hardware.h> #include <lcd.h> #include <atmel_lcdc.h> -#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) -#include <net.h> -#endif -#include <netdev.h> -#include <atmel_mci.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -77,34 +72,6 @@ static void at91sam9263ek_nand_hw_init(void) } #endif
-#ifdef CONFIG_MACB -static void at91sam9263ek_macb_hw_init(void) -{ - at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; - - at91_periph_clk_enable(ATMEL_ID_EMAC); - - /* - * Disable pull-up on: - * RXDV (PC25) => PHY normal mode (not Test mode) - * ERX0 (PE25) => PHY ADDR0 - * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0 - * - * PHY has internal pull-down - */ - writel(1 << 25, &pio->pioc.pudr); - writel((1 << 25) | (1 <<26), &pio->pioe.pudr); - - at91_phy_reset(); - - /* Re-enable pull-up */ - writel(1 << 25, &pio->pioc.puer); - writel((1 << 25) | (1 <<26), &pio->pioe.puer); - - at91_macb_hw_init(); -} -#endif - #ifdef CONFIG_LCD vidinfo_t panel_info = { .vl_col = 240, @@ -209,22 +176,8 @@ void lcd_show_board_info(void) #endif /* CONFIG_LCD_INFO */ #endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI -int board_mmc_init(bd_t *bd) -{ - at91_mci_hw_init(); - - return atmel_mci_init((void *)ATMEL_BASE_MCI1); -} -#endif - int board_early_init_f(void) { - at91_periph_clk_enable(ATMEL_ID_PIOA); - at91_periph_clk_enable(ATMEL_ID_PIOB); - at91_periph_clk_enable(ATMEL_ID_PIOCDE); - - at91_seriald_hw_init(); return 0; }
@@ -242,9 +195,6 @@ int board_init(void) at91_set_pio_output(AT91_PIO_PORTE, 20, 1); /* select spi0 clock */ at91_spi0_hw_init(1 << 0); #endif -#ifdef CONFIG_MACB - at91sam9263ek_macb_hw_init(); -#endif #ifdef CONFIG_USB_OHCI_NEW at91_uhp_hw_init(); #endif @@ -267,12 +217,3 @@ void reset_phy(void) { } #endif - -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_MACB - rc = macb_eth_initialize(0, (void *) ATMEL_BASE_EMAC, 0x00); -#endif - return rc; -}