Hi Marek
On 12/1/20 11:34 AM, Marek Vasut wrote:
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P. To permit PLL4P to run at faster frequency, use MCO2 as a divider. The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to 50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback clock are fed back in via pin PA1.
Signed-off-by: Marek Vasut marex@denx.de Cc: Patrice Chotard patrice.chotard@st.com Cc: Patrick Delaunay patrick.delaunay@st.com
NOTE: This is for next
arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi | 25 +++++++++++++++++----- arch/arm/dts/stm32mp15xx-dhcom.dtsi | 3 +-- 2 files changed, 21 insertions(+), 7 deletions(-)
diff --git a/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi index 92345b7ba3..6868769c6e 100644 --- a/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi +++ b/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi @@ -72,8 +72,8 @@
&pinctrl { /* These should bound to FMC2 bus driver, but we do not have one */
- pinctrl-0 = <&fmc_pins_b>;
- pinctrl-1 = <&fmc_sleep_pins_b>;
pinctrl-0 = <&fmc_pins_b &mco2_pins_a>;
pinctrl-1 = <&fmc_sleep_pins_b &mco2_sleep_pins_a>; pinctrl-names = "default", "sleep";
fmc_pins_b: fmc-0 {
@@ -130,6 +130,21 @@ <STM32_PINMUX('G', 12, ANALOG)>; /* FMC_NE4 */ }; };
- mco2_pins_a: mco2-0 {
pins {pinmux = <STM32_PINMUX('G', 2, AF1)>; /* MCO2 */bias-disable;drive-push-pull;slew-rate = <2>;};- };
- mco2_sleep_pins_a: mco2-sleep-0 {
pins {pinmux = <STM32_PINMUX('G', 2, ANALOG)>; /* MCO2 */};- };
};
&pmic { @@ -181,7 +196,7 @@ CLK_PLL4_HSE CLK_RTC_LSE CLK_MCO1_DISABLED
CLK_MCO2_DISABLED
CLK_MCO2_PLL4P;
st,clkdiv = <
@@ -195,7 +210,7 @@ 2 /*APB5*/ 23 /*RTC*/ 0 /*MCO1*/
0 /*MCO2*/
1 /*MCO2*/;
st,pkcs = <
@@ -258,7 +273,7 @@ pll4: st,pll@3 { compatible = "st,stm32mp1-pll"; reg = <3>;
cfg = < 1 49 11 11 11 PQR(1,1,1) >;
cfg = < 1 49 5 11 11 PQR(1,1,1) >;}; diff --git a/arch/arm/dts/stm32mp15xx-dhcom.dtsi b/arch/arm/dts/stm32mp15xx-dhcom.dtsi index dafcce4323..a1d1b8dec7 100644 --- a/arch/arm/dts/stm32mp15xx-dhcom.dtsi +++ b/arch/arm/dts/stm32mp15xx-dhcom.dtsi @@ -58,7 +58,6 @@ phy-mode = "rmii"; max-speed = <100>; phy-handle = <&phy0>;
st,eth_ref_clk_sel; phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
mdio0 {
@@ -267,7 +266,7 @@ pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */ <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */ <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
<STM32_PINMUX('A', 1, AF0)>, /* ETH1_RMII_REF_CLK */
<STM32_PINMUX('A', 1, AF11)>, /* ETH1_RMII_REF_CLK */ <STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO */ <STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC */ bias-disable;
Reviewed-by: Patrice Chotard patrice.chotard@st.com
Thanks
Patrice