At this point in time we can now remove our legacy code and switch to enabling DM for USB and Ethernet.
Cc: Derald D. Woods woods.technical@gmail.com Cc: Adam Ford aford173@gmail.com Signed-off-by: Tom Rini trini@konsulko.com --- board/ti/beagle/beagle.c | 70 ---------------------------------- configs/omap3_beagle_defconfig | 5 ++- 2 files changed, 4 insertions(+), 71 deletions(-)
diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c index 9139ad87d400..9ccd566da370 100644 --- a/board/ti/beagle/beagle.c +++ b/board/ti/beagle/beagle.c @@ -40,11 +40,6 @@ #include "beagle.h" #include <command.h>
-#ifdef CONFIG_USB_EHCI_HCD -#include <usb.h> -#include <asm/ehci-omap.h> -#endif - #define TWL4030_I2C_BUS 0 #define EXPANSION_EEPROM_I2C_BUS 1 #define EXPANSION_EEPROM_I2C_ADDRESS 0x50 @@ -297,33 +292,6 @@ static void beagle_dvi_pup(void) } #endif
-#ifdef CONFIG_USB_MUSB_OMAP2PLUS -static struct musb_hdrc_config musb_config = { - .multipoint = 1, - .dyn_fifo = 1, - .num_eps = 16, - .ram_bits = 12, -}; - -static struct omap_musb_board_data musb_board_data = { - .interface_type = MUSB_INTERFACE_ULPI, -}; - -static struct musb_hdrc_platform_data musb_plat = { -#if defined(CONFIG_USB_MUSB_HOST) - .mode = MUSB_HOST, -#elif defined(CONFIG_USB_MUSB_GADGET) - .mode = MUSB_PERIPHERAL, -#else -#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" -#endif - .config = &musb_config, - .power = 100, - .platform_ops = &omap2430_ops, - .board_data = &musb_board_data, -}; -#endif - /* * Routine: misc_init_r * Description: Configure board specific parts @@ -506,10 +474,6 @@ int misc_init_r(void) omap3_dss_enable(); #endif
-#ifdef CONFIG_USB_MUSB_OMAP2PLUS - musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE); -#endif - if (generate_fake_mac) omap_die_id_usbethaddr();
@@ -548,37 +512,3 @@ void board_mmc_power_init(void) twl4030_power_mmc_init(0); } #endif - -#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) -/* Call usb_stop() before starting the kernel */ -void show_boot_progress(int val) -{ - if (val == BOOTSTAGE_ID_RUN_OS) - usb_stop(); -} - -static struct omap_usbhs_board_data usbhs_bdata = { - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED -}; - -int ehci_hcd_init(int index, enum usb_init_type init, - struct ehci_hccr **hccr, struct ehci_hcor **hcor) -{ - return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); -} - -int ehci_hcd_stop(int index) -{ - return omap_ehci_hcd_stop(); -} - -#endif /* CONFIG_USB_EHCI_HCD */ - -#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) -int board_eth_init(bd_t *bis) -{ - return usb_eth_initialize(bis); -} -#endif diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig index ed7cb8f2ff63..b08ffc062d29 100644 --- a/configs/omap3_beagle_defconfig +++ b/configs/omap3_beagle_defconfig @@ -3,11 +3,11 @@ CONFIG_ARM=y # CONFIG_SPL_USE_ARCH_MEMSET is not set CONFIG_ARCH_OMAP2PLUS=y CONFIG_SYS_MALLOC_F_LEN=0x4000 +CONFIG_SPL_TEXT_BASE=0x40200000 CONFIG_TARGET_OMAP3_BEAGLE=y CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0x40200000 CONFIG_DISTRO_DEFAULTS=y CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" CONFIG_USE_PREBOOT=y @@ -73,10 +73,13 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 CONFIG_SPL_NAND_SIMPLE=y +CONFIG_DM_ETH=y CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_OMAP3_SPI=y CONFIG_USB=y +CONFIG_DM_USB=y +# CONFIG_SPL_DM_USB is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_OMAP3=y CONFIG_USB_MUSB_GADGET=y