Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications: * Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz * 2 / 4 / 8 GB of DDR4 DRAM * 16 GB eMMC * 4MB SPI-NOR (Bootloader) * 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only) * 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only) * 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C) * 1x SATA 7+15 socket (SATA3) * 1x 16-pin (2×8) MikroBus Connector * 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots) * 2x USB3.0 Type-A ports via SMSC USB5434B hub * Cortex 2x5 JTAG * microUSB port for UART (PL2303GL/PL2303SA onboard) * 1x 10G SFP+ * 1x 1G SFP (Connected to 88E1512 PHY) * 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY) * 4x 1G RJ45 ports via Topaz 88E6141 switch * RTC with battery holder (SoC provided, requires CR2032 battery) * 1x 12V DC IN * 1x Power switch * 1x 12V fan header (3-pin, power only) * 1x mini-PCIe LED header (2x0.1" pins) * 1x M.2-2280 LED header (2x0.1" pins) * 6x Bootstrap jumpers * 1x Power LED (Green) * 3x Tri-color RGB LEDs (Controllable) * 1x Microchip ATECC608B secure element
Note that 1G SFP does not work in U-boot as it would require Linux like SFP support for parsing module interface and reconfiguring the PHY.
Additionally, automatic import of the Marvell hw_info parameters is enabled via the recently added mac command for Armada platforms. The parameters stored in Marvell hw_info are usually the board serial number and MAC addresses.
Signed-off-by: Robert Marko robert.marko@sartura.hr --- Changes in v3: * Rename "u-boot" partition to "firmware" which better describes its content * Remove read-only flag from "hw-info" partition
Changes in v2: * Add DT compatible for hw-info to its partition * Enable MTD support, command and SPI MTD command --- arch/arm/dts/Makefile | 1 + arch/arm/dts/armada-7040-mochabin.dts | 304 +++++++++++++++++++++++ configs/mvebu_mochabin-88f7040_defconfig | 88 +++++++ 3 files changed, 393 insertions(+) create mode 100644 arch/arm/dts/armada-7040-mochabin.dts create mode 100644 configs/mvebu_mochabin-88f7040_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index a88aecc5bd9..dea567d2595 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -232,6 +232,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += \ armada-38x-controlcenterdc.dtb \ armada-7040-db-nand.dtb \ armada-7040-db.dtb \ + armada-7040-mochabin.dtb \ armada-8040-clearfog-gt-8k.dtb \ armada-8040-db.dtb \ armada-8040-mcbin.dtb \ diff --git a/arch/arm/dts/armada-7040-mochabin.dts b/arch/arm/dts/armada-7040-mochabin.dts new file mode 100644 index 00000000000..84f06363728 --- /dev/null +++ b/arch/arm/dts/armada-7040-mochabin.dts @@ -0,0 +1,304 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (C) 2016- 2021 Marvell International Ltd. + * Copyright (C) 2021 Sartura Ltd. + */ + +/* + * Device Tree file for Globalscale MOCHAbin + * Boot device: SPI NOR, 0x32 (SW3) + */ + +#include "armada-7040.dtsi" + +/ { + model = "Globalscale MOCHAbin"; + compatible = "globalscale,mochabin", "marvell,armada7040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + i2c0 = &cp0_i2c0; + spi0 = &cp0_spi1; + }; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; +}; + +&ap_pinctl { + /* MPP Bus: + * SDIO [0-5] + * UART0 [11,19] + */ + /* 0 1 2 3 4 5 6 7 8 9 */ + pin-func = < 1 1 1 1 1 1 0 0 0 0 + 0 3 0 0 0 0 0 0 0 3 >; +}; + +/* microUSB UART console */ +&uart0 { + status = "okay"; +}; + +/* eMMC */ +&ap_sdhci0 { + status = "okay"; + + bus-width = <4>; + no-1-8-v; + non-removable; +}; + +&cp0_pinctl { + /* MPP Bus: + * E6341_RSTn [0] + * E6341_INT [1] + * I2C1 [2,3] + * PCIE_CLKREQn [5] + * UART0 [6,7] + * PCIE_WAKEn [8] + * PCIE_RSTOUTn [9] (GPIO) + * DEVSLP_M2-2 [10] + * PHY0_RSTn [12] (88E1512 PHY RST) + * SPI1 [13-16] + * PHY0_INT [24] (88E1512 PHY INT) + * 9554_INT [27] (PCA9554 INT) + * IS_CLK_VBM [29] (is31fl3199-clk-vbm) + * IS_SDB [30] (is31fl3199-sdb) + * MKR_PWM [31] (mikroBus PWM) + * MKR_INT [32] (mikroBus INT) + * MKR_RST [33] (mikroBus RST) + * DEVSLP_M2-1 [34] (M.2 SATA DevSlp) + * SMI [35,36] + * I2C0 [37,38] + * RGMII2 [44-55] + * SPI0 [56-59] + * GPIO [4,11,17-23,25-26,28] + */ + /* 0 1 2 3 4 5 6 7 8 9 */ + pin-func = < 0 0 7 7 0 7 8 8 0 0 + 0 0 0 3 3 3 3 0 0 0 + 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 8 8 2 2 0 + 0 0 0 0 1 1 1 1 1 1 + 1 1 1 1 1 1 6 6 6 6 + 0 0 0 >; + + cp0_i2c1_pins: cp0-i2c-pins-1 { + marvell,pins = < 2 3 >; + marvell,function = <7>; + }; + + cp0_spi0_pins: cp0-spi-pins-0 { + marvell,pins = < 56 57 58 59 >; + marvell,function = <6>; + }; + + cp0_spi1_pins: cp0-spi-pins-1 { + marvell,pins = < 13 14 15 16 >; + marvell,function = <3>; + }; + + cp0_smi_pins: cp0-smi-pins { + marvell,pins = < 35 36 >; + marvell,function = <8>; + }; +}; + +/* mikroBUS SPI */ +&cp0_spi0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi0_pins>; +}; + +/* SPI-NOR */ +&cp0_spi1 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi1_pins>; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "firmware"; + reg = <0x0 0x3e0000>; + }; + + partition@3e0000 { + compatible = "marvell,hw-info"; + label = "hw-info"; + reg = <0x3e0000 0x10000>; + }; + + partition@3f0000 { + label = "u-boot-env"; + reg = <0x3f0000 0x10000>; + }; + }; + }; +}; + +/* mikroBUS, 1G SFP and GPIO expander */ +&cp0_i2c0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + clock-frequency = <100000>; + + sfp_gpio: pca9554@39 { + compatible = "nxp,pca9554"; + reg = <0x39>; + + gpio-controller; + #gpio-cells = <2>; + + /* + * IO0_0: SFP+_TX_FAULT + * IO0_1: SFP+_TX_DISABLE + * IO0_2: SFP+_PRSNT + * IO0_3: SFP+_LOSS + * IO0_4: SFP_TX_FAULT + * IO0_5: SFP_TX_DISABLE + * IO0_6: SFP_PRSNT + * IO0_7: SFP_LOSS + */ + }; +}; + +/* IS31FL3199, mini-PCIe and 10G SFP+ */ +&cp0_i2c1 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c1_pins>; + clock-frequency = <100000>; +}; + +&cp0_comphy { + phy0 { + phy-type = <COMPHY_TYPE_SGMII1>; + phy-speed = <COMPHY_SPEED_3_125G>; + }; + + phy1 { + phy-type = <COMPHY_TYPE_USB3_HOST0>; + }; + + phy2 { + phy-type = <COMPHY_TYPE_SATA0>; + }; + + phy3 { + phy-type = <COMPHY_TYPE_SATA1>; + }; + + phy4 { + phy-type = <COMPHY_TYPE_SFI0>; + phy-speed = <COMPHY_SPEED_10_3125G>; + }; + + phy5 { + phy-type = <COMPHY_TYPE_PEX2>; + }; +}; + +&cp0_sata0 { + status = "okay"; +}; + +/* SMSC USB5434B hub */ +&cp0_usb3_0 { + status = "okay"; +}; + +/* miniPCI-E USB */ +&cp0_usb3_1 { + status = "okay"; +}; + +/* SMSC USB5434B hub */ +&cp0_utmi0 { + status = "okay"; +}; + +/* miniPCI-E USB */ +&cp0_utmi1 { + status = "okay"; +}; + +/* miniPCI-E (J5) */ +&cp0_pcie2 { + status = "okay"; + marvell,reset-gpio = <&cp0_gpio0 9 GPIO_ACTIVE_LOW>; +}; + +&cp0_mdio { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_smi_pins>; + + /* 88E1512 PHY */ + eth2phy: ethernet-phy@1 { + reg = <1>; + }; +}; + +&cp0_ethernet { + status = "okay"; +}; + +/* 10G SFP+ */ +&cp0_eth0 { + status = "okay"; + + phy-mode = "sfi"; + managed = "in-band-status"; + marvell,sfp-tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>; +}; + +/* Topaz switch uplink */ +&cp0_eth1 { + status = "okay"; + + phy-mode = "2500base-x"; + phy-reset-gpios = <&cp0_gpio0 0 GPIO_ACTIVE_LOW>; + + fixed-link { + speed = <2500>; + full-duplex; + }; +}; + +/* 1G SFP or 1G RJ45 */ +&cp0_eth2 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_ge2_rgmii_pins>; + + phy-mode = "rgmii-id"; + phy = <ð2phy>; + marvell,sfp-tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>; + phy-reset-gpios = <&cp0_gpio0 12 GPIO_ACTIVE_LOW>; +}; diff --git a/configs/mvebu_mochabin-88f7040_defconfig b/configs/mvebu_mochabin-88f7040_defconfig new file mode 100644 index 00000000000..cbd2f944c93 --- /dev/null +++ b/configs/mvebu_mochabin-88f7040_defconfig @@ -0,0 +1,88 @@ +CONFIG_ARM=y +CONFIG_ARCH_CPU_INIT=y +CONFIG_ARCH_MVEBU=y +CONFIG_SYS_TEXT_BASE=0x00000000 +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_NR_DRAM_BANKS=2 +CONFIG_TARGET_MVEBU_ARMADA_8K=y +CONFIG_MVEBU_MAC_HW_INFO=y +CONFIG_ENV_SIZE=0x10000 +CONFIG_ENV_OFFSET=0x3f0000 +CONFIG_ENV_SECT_SIZE=0x10000 +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="armada-7040-mochabin" +CONFIG_DEBUG_UART_BASE=0xf0512000 +CONFIG_DEBUG_UART_CLOCK=200000000 +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_PROMPT="Autoboot in %d seconds, to stop use 's' key\n" +CONFIG_AUTOBOOT_STOP_STR="s" +CONFIG_AUTOBOOT_KEYED_CTRLC=y +CONFIG_USE_PREBOOT=y +CONFIG_SYS_CONSOLE_INFO_QUIET=y +# CONFIG_DISPLAY_CPUINFO is not set +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_ARCH_EARLY_INIT_R=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +# CONFIG_RANDOM_UUID is not set +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SATA=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_MVEBU_BUBT=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_EXT4_WRITE=y +# CONFIG_ISO_PARTITION is not set +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_AHCI_MVEBU=y +CONFIG_GPIO_HOG=y +CONFIG_DM_PCA953X=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_MISC=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_XENON=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHY_MARVELL=y +CONFIG_PHY_GIGE=y +CONFIG_MVPP2=y +CONFIG_RGMII=y +CONFIG_PCI=y +CONFIG_PCIE_DW_MVEBU=y +CONFIG_PHY=y +CONFIG_MVEBU_COMPHY_SUPPORT=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_ARMADA_8K=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_RTC=y +CONFIG_RTC_ARMADA38X=y +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_SYS_NS16550=y +CONFIG_KIRKWOOD_SPI=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +# CONFIG_EFI_LOADER is not set