Bring in the device tree files from Linux v4.1.
Signed-off-by: Simon Glass sjg@chromium.org ---
arch/arm/dts/Makefile | 2 + arch/arm/dts/bcm2835-rpi-b.dts | 23 ++++ arch/arm/dts/bcm2835-rpi.dtsi | 51 +++++++++ arch/arm/dts/bcm2835.dtsi | 192 ++++++++++++++++++++++++++++++++++ include/dt-bindings/pinctrl/bcm2835.h | 27 +++++ 5 files changed, 295 insertions(+) create mode 100644 arch/arm/dts/bcm2835-rpi-b.dts create mode 100644 arch/arm/dts/bcm2835-rpi.dtsi create mode 100644 arch/arm/dts/bcm2835.dtsi create mode 100644 include/dt-bindings/pinctrl/bcm2835.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 9c735c6..b284a2d 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -49,6 +49,8 @@ dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \ zynq-zc770-xm013.dtb dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb
+dtb-$(CONFIG_ARCH_BCM283X) += bcm2835-rpi-b.dtb + dtb-$(CONFIG_ARCH_SOCFPGA) += \ socfpga_arria5_socdk.dtb \ socfpga_cyclone5_socdk.dtb \ diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts new file mode 100644 index 0000000..ee89b79 --- /dev/null +++ b/arch/arm/dts/bcm2835-rpi-b.dts @@ -0,0 +1,23 @@ +/dts-v1/; +#include "bcm2835-rpi.dtsi" + +/ { + compatible = "raspberrypi,model-b", "brcm,bcm2835"; + model = "Raspberry Pi Model B"; + + leds { + act { + gpios = <&gpio 16 1>; + }; + }; +}; + +&gpio { + pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>; + + /* I2S interface */ + i2s_alt2: i2s_alt2 { + brcm,pins = <28 29 30 31>; + brcm,function = <BCM2835_FSEL_ALT2>; + }; +}; diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi new file mode 100644 index 0000000..46780bb --- /dev/null +++ b/arch/arm/dts/bcm2835-rpi.dtsi @@ -0,0 +1,51 @@ +#include "bcm2835.dtsi" + +/ { + memory { + reg = <0 0x10000000>; + }; + + leds { + compatible = "gpio-leds"; + + act { + label = "ACT"; + default-state = "keep"; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + + gpioout: gpioout { + brcm,pins = <6>; + brcm,function = <BCM2835_FSEL_GPIO_OUT>; + }; + + alt0: alt0 { + brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>; + brcm,function = <BCM2835_FSEL_ALT0>; + }; + + alt3: alt3 { + brcm,pins = <48 49 50 51 52 53>; + brcm,function = <BCM2835_FSEL_ALT3>; + }; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <100000>; +}; + +&sdhci { + status = "okay"; + bus-width = <4>; +}; diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi new file mode 100644 index 0000000..301c73f --- /dev/null +++ b/arch/arm/dts/bcm2835.dtsi @@ -0,0 +1,192 @@ +#include <dt-bindings/pinctrl/bcm2835.h> +#include "skeleton.dtsi" + +/ { + compatible = "brcm,bcm2835"; + model = "BCM2835"; + interrupt-parent = <&intc>; + + chosen { + bootargs = "earlyprintk console=ttyAMA0"; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x7e000000 0x20000000 0x02000000>; + dma-ranges = <0x40000000 0x00000000 0x20000000>; + + timer@7e003000 { + compatible = "brcm,bcm2835-system-timer"; + reg = <0x7e003000 0x1000>; + interrupts = <1 0>, <1 1>, <1 2>, <1 3>; + clock-frequency = <1000000>; + }; + + dma: dma@7e007000 { + compatible = "brcm,bcm2835-dma"; + reg = <0x7e007000 0xf00>; + interrupts = <1 16>, + <1 17>, + <1 18>, + <1 19>, + <1 20>, + <1 21>, + <1 22>, + <1 23>, + <1 24>, + <1 25>, + <1 26>, + <1 27>, + <1 28>; + + #dma-cells = <1>; + brcm,dma-channel-mask = <0x7f35>; + }; + + intc: interrupt-controller@7e00b200 { + compatible = "brcm,bcm2835-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + watchdog@7e100000 { + compatible = "brcm,bcm2835-pm-wdt"; + reg = <0x7e100000 0x28>; + }; + + rng@7e104000 { + compatible = "brcm,bcm2835-rng"; + reg = <0x7e104000 0x10>; + }; + + mailbox: mailbox@7e00b800 { + compatible = "brcm,bcm2835-mbox"; + reg = <0x7e00b880 0x40>; + interrupts = <0 1>; + #mbox-cells = <0>; + }; + + gpio: gpio@7e200000 { + compatible = "brcm,bcm2835-gpio"; + reg = <0x7e200000 0xb4>; + /* + * The GPIO IP block is designed for 3 banks of GPIOs. + * Each bank has a GPIO interrupt for itself. + * There is an overall "any bank" interrupt. + * In order, these are GIC interrupts 17, 18, 19, 20. + * Since the BCM2835 only has 2 banks, the 2nd bank + * interrupt output appears to be mirrored onto the + * 3rd bank's interrupt signal. + * So, a bank0 interrupt shows up on 17, 20, and + * a bank1 interrupt shows up on 18, 19, 20! + */ + interrupts = <2 17>, <2 18>, <2 19>, <2 20>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart@7e201000 { + compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; + reg = <0x7e201000 0x1000>; + interrupts = <2 25>; + clock-frequency = <3000000>; + arm,primecell-periphid = <0x00241011>; + }; + + i2s: i2s@7e203000 { + compatible = "brcm,bcm2835-i2s"; + reg = <0x7e203000 0x20>, + <0x7e101098 0x02>; + + dmas = <&dma 2>, + <&dma 3>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + spi: spi@7e204000 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204000 0x1000>; + interrupts = <2 22>; + clocks = <&clk_spi>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c0: i2c@7e205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x1000>; + interrupts = <2 21>; + clocks = <&clk_i2c>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + sdhci: sdhci@7e300000 { + compatible = "brcm,bcm2835-sdhci"; + reg = <0x7e300000 0x100>; + interrupts = <2 30>; + clocks = <&clk_mmc>; + status = "disabled"; + }; + + i2c1: i2c@7e804000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e804000 0x1000>; + interrupts = <2 21>; + clocks = <&clk_i2c>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + usb@7e980000 { + compatible = "brcm,bcm2835-usb"; + reg = <0x7e980000 0x10000>; + interrupts = <1 9>; + }; + + arm-pmu { + compatible = "arm,arm1176-pmu"; + }; + }; + + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + clk_mmc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-output-names = "mmc"; + clock-frequency = <100000000>; + }; + + clk_i2c: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-output-names = "i2c"; + clock-frequency = <250000000>; + }; + + clk_spi: clock@2 { + compatible = "fixed-clock"; + reg = <2>; + #clock-cells = <0>; + clock-output-names = "spi"; + clock-frequency = <250000000>; + }; + }; +}; diff --git a/include/dt-bindings/pinctrl/bcm2835.h b/include/dt-bindings/pinctrl/bcm2835.h new file mode 100644 index 0000000..6f0bc37 --- /dev/null +++ b/include/dt-bindings/pinctrl/bcm2835.h @@ -0,0 +1,27 @@ +/* + * Header providing constants for bcm2835 pinctrl bindings. + * + * Copyright (C) 2015 Stefan Wahren stefan.wahren@i2se.com + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DT_BINDINGS_PINCTRL_BCM2835_H__ +#define __DT_BINDINGS_PINCTRL_BCM2835_H__ + +/* brcm,function property */ +#define BCM2835_FSEL_GPIO_IN 0 +#define BCM2835_FSEL_GPIO_OUT 1 +#define BCM2835_FSEL_ALT5 2 +#define BCM2835_FSEL_ALT4 3 +#define BCM2835_FSEL_ALT0 4 +#define BCM2835_FSEL_ALT1 5 +#define BCM2835_FSEL_ALT2 6 +#define BCM2835_FSEL_ALT3 7 + +#endif /* __DT_BINDINGS_PINCTRL_BCM2835_H__ */