We didn't convert the Integrator to use DM for PCI in time, and we don't use it either so let's just drop PCI support from the Integrator.
Signed-off-by: Linus Walleij linus.walleij@linaro.org --- board/armltd/integrator/Makefile | 1 - board/armltd/integrator/integrator.c | 1 - board/armltd/integrator/pci.c | 462 ------------------------ board/armltd/integrator/pci_v3.h | 187 ---------- configs/integratorap_cm720t_defconfig | 4 - configs/integratorap_cm920t_defconfig | 4 - configs/integratorap_cm926ejs_defconfig | 4 - configs/integratorap_cm946es_defconfig | 4 - 8 files changed, 667 deletions(-) delete mode 100644 board/armltd/integrator/pci.c delete mode 100644 board/armltd/integrator/pci_v3.h
diff --git a/board/armltd/integrator/Makefile b/board/armltd/integrator/Makefile index 8c906e3f072b..107e59bf0fa2 100644 --- a/board/armltd/integrator/Makefile +++ b/board/armltd/integrator/Makefile @@ -10,5 +10,4 @@ obj-y := lowlevel_init.o
obj-y += integrator.o -obj-$(CONFIG_PCI) += pci.o obj-y += timer.o diff --git a/board/armltd/integrator/integrator.c b/board/armltd/integrator/integrator.c index 3e864e8e7a5c..388795809dfd 100644 --- a/board/armltd/integrator/integrator.c +++ b/board/armltd/integrator/integrator.c @@ -181,7 +181,6 @@ int board_eth_init(struct bd_info *bis) #ifdef CONFIG_SMC91111 rc = smc91111_initialize(0, CONFIG_SMC91111_BASE); #endif - rc += pci_eth_init(bis); return rc; } #endif diff --git a/board/armltd/integrator/pci.c b/board/armltd/integrator/pci.c deleted file mode 100644 index 28efc33f1f42..000000000000 --- a/board/armltd/integrator/pci.c +++ /dev/null @@ -1,462 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger mgroeger@sysgo.de - * - * (C) Copyright 2002 - * David Mueller, ELSOFT AG, d.mueller@elsoft.ch - * - * (C) Copyright 2003 - * Texas Instruments, <www.ti.com> - * Kshitij Gupta Kshitij@ti.com - * - * (C) Copyright 2004 - * ARM Ltd. - * Philippe Robin, philippe.robin@arm.com - * - * (C) Copyright 2011 - * Linaro - * Linus Walleij linus.walleij@linaro.org - */ -#include <common.h> -#include <init.h> -#include <log.h> -#include <pci.h> -#include <asm/io.h> -#include <linux/bug.h> -#include <linux/delay.h> -#include "integrator-sc.h" -#include "pci_v3.h" - -#define INTEGRATOR_BOOT_ROM_BASE 0x20000000 -#define INTEGRATOR_HDR0_SDRAM_BASE 0x80000000 - -/* - * These are in the physical addresses on the CPU side, i.e. - * where we read and write stuff - you don't want to try to - * move these around - */ -#define PHYS_PCI_MEM_BASE 0x40000000 -#define PHYS_PCI_IO_BASE 0x60000000 /* PCI I/O space base */ -#define PHYS_PCI_CONFIG_BASE 0x61000000 -#define PHYS_PCI_V3_BASE 0x62000000 /* V360EPC registers */ -#define SZ_256M 0x10000000 - -/* - * These are in the PCI BUS address space - * Set to 0x00000000 in the Linux kernel, 0x40000000 in Boot monitor - * we follow the example of the kernel, because that is the address - * range that devices actually use - what would they be doing at - * 0x40000000? - */ -#define PCI_BUS_NONMEM_START 0x00000000 -#define PCI_BUS_NONMEM_SIZE SZ_256M - -#define PCI_BUS_PREMEM_START (PCI_BUS_NONMEM_START + PCI_BUS_NONMEM_SIZE) -#define PCI_BUS_PREMEM_SIZE SZ_256M - -#if PCI_BUS_NONMEM_START & 0x000fffff -#error PCI_BUS_NONMEM_START must be megabyte aligned -#endif -#if PCI_BUS_PREMEM_START & 0x000fffff -#error PCI_BUS_PREMEM_START must be megabyte aligned -#endif - -/* - * Initialize PCI Devices, report devices found. - */ - -#ifndef CONFIG_PCI_PNP -#define PCI_ENET0_IOADDR 0x60000000 /* First card in PCI I/O space */ -#define PCI_ENET0_MEMADDR 0x40000000 /* First card in PCI memory space */ -static struct pci_config_table pci_integrator_config_table[] = { - { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID, - pci_cfgfunc_config_device, { PCI_ENET0_IOADDR, - PCI_ENET0_MEMADDR, - PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }}, - { } -}; -#endif /* CONFIG_PCI_PNP */ - -/* V3 access routines */ -#define v3_writeb(o, v) __raw_writeb(v, PHYS_PCI_V3_BASE + (unsigned int)(o)) -#define v3_readb(o) (__raw_readb(PHYS_PCI_V3_BASE + (unsigned int)(o))) - -#define v3_writew(o, v) __raw_writew(v, PHYS_PCI_V3_BASE + (unsigned int)(o)) -#define v3_readw(o) (__raw_readw(PHYS_PCI_V3_BASE + (unsigned int)(o))) - -#define v3_writel(o, v) __raw_writel(v, PHYS_PCI_V3_BASE + (unsigned int)(o)) -#define v3_readl(o) (__raw_readl(PHYS_PCI_V3_BASE + (unsigned int)(o))) - -static unsigned long v3_open_config_window(pci_dev_t bdf, int offset) -{ - unsigned int address, mapaddress; - unsigned int busnr = PCI_BUS(bdf); - unsigned int devfn = PCI_FUNC(bdf); - - /* - * Trap out illegal values - */ - if (offset > 255) - BUG(); - if (busnr > 255) - BUG(); - if (devfn > 255) - BUG(); - - if (busnr == 0) { - /* - * Linux calls the thing U-Boot calls "DEV" "SLOT" - * instead, but it's the same 5 bits - */ - int slot = PCI_DEV(bdf); - - /* - * local bus segment so need a type 0 config cycle - * - * build the PCI configuration "address" with one-hot in - * A31-A11 - * - * mapaddress: - * 3:1 = config cycle (101) - * 0 = PCI A1 & A0 are 0 (0) - */ - address = PCI_FUNC(bdf) << 8; - mapaddress = V3_LB_MAP_TYPE_CONFIG; - - if (slot > 12) - /* - * high order bits are handled by the MAP register - */ - mapaddress |= 1 << (slot - 5); - else - /* - * low order bits handled directly in the address - */ - address |= 1 << (slot + 11); - } else { - /* - * not the local bus segment so need a type 1 config cycle - * - * address: - * 23:16 = bus number - * 15:11 = slot number (7:3 of devfn) - * 10:8 = func number (2:0 of devfn) - * - * mapaddress: - * 3:1 = config cycle (101) - * 0 = PCI A1 & A0 from host bus (1) - */ - mapaddress = V3_LB_MAP_TYPE_CONFIG | V3_LB_MAP_AD_LOW_EN; - address = (busnr << 16) | (devfn << 8); - } - - /* - * Set up base0 to see all 512Mbytes of memory space (not - * prefetchable), this frees up base1 for re-use by - * configuration memory - */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | - V3_LB_BASE_ADR_SIZE_512MB | V3_LB_BASE_ENABLE); - - /* - * Set up base1/map1 to point into configuration space. - */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_CONFIG_BASE) | - V3_LB_BASE_ADR_SIZE_16MB | V3_LB_BASE_ENABLE); - v3_writew(V3_LB_MAP1, mapaddress); - - return PHYS_PCI_CONFIG_BASE + address + offset; -} - -static void v3_close_config_window(void) -{ - /* - * Reassign base1 for use by prefetchable PCI memory - */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE + SZ_256M) | - V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH | - V3_LB_BASE_ENABLE); - v3_writew(V3_LB_MAP1, v3_addr_to_lb_map(PCI_BUS_PREMEM_START) | - V3_LB_MAP_TYPE_MEM_MULTIPLE); - - /* - * And shrink base0 back to a 256M window (NOTE: MAP0 already correct) - */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | - V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE); -} - -static int pci_integrator_read_byte(struct pci_controller *hose, pci_dev_t bdf, - int offset, unsigned char *val) -{ - unsigned long addr; - - addr = v3_open_config_window(bdf, offset); - *val = __raw_readb(addr); - v3_close_config_window(); - return 0; -} - -static int pci_integrator_read__word(struct pci_controller *hose, - pci_dev_t bdf, int offset, - unsigned short *val) -{ - unsigned long addr; - - addr = v3_open_config_window(bdf, offset); - *val = __raw_readw(addr); - v3_close_config_window(); - return 0; -} - -static int pci_integrator_read_dword(struct pci_controller *hose, - pci_dev_t bdf, int offset, - unsigned int *val) -{ - unsigned long addr; - - addr = v3_open_config_window(bdf, offset); - *val = __raw_readl(addr); - v3_close_config_window(); - return 0; -} - -static int pci_integrator_write_byte(struct pci_controller *hose, - pci_dev_t bdf, int offset, - unsigned char val) -{ - unsigned long addr; - - addr = v3_open_config_window(bdf, offset); - __raw_writeb((u8)val, addr); - __raw_readb(addr); - v3_close_config_window(); - return 0; -} - -static int pci_integrator_write_word(struct pci_controller *hose, - pci_dev_t bdf, int offset, - unsigned short val) -{ - unsigned long addr; - - addr = v3_open_config_window(bdf, offset); - __raw_writew((u8)val, addr); - __raw_readw(addr); - v3_close_config_window(); - return 0; -} - -static int pci_integrator_write_dword(struct pci_controller *hose, - pci_dev_t bdf, int offset, - unsigned int val) -{ - unsigned long addr; - - addr = v3_open_config_window(bdf, offset); - __raw_writel((u8)val, addr); - __raw_readl(addr); - v3_close_config_window(); - return 0; -} - -struct pci_controller integrator_hose = { -#ifndef CONFIG_PCI_PNP - config_table: pci_integrator_config_table, -#endif -}; - -void pci_init_board(void) -{ - struct pci_controller *hose = &integrator_hose; - u16 val; - - /* setting this register will take the V3 out of reset */ - __raw_writel(SC_PCI_PCIEN, SC_PCI); - - /* Wait for 230 ms (from spec) before accessing any V3 registers */ - mdelay(230); - - /* Now write the Base I/O Address Word to PHYS_PCI_V3_BASE + 0x6E */ - v3_writew(V3_LB_IO_BASE, (PHYS_PCI_V3_BASE >> 16)); - - /* Wait for the mailbox to settle */ - do { - v3_writeb(V3_MAIL_DATA, 0xAA); - v3_writeb(V3_MAIL_DATA + 4, 0x55); - } while (v3_readb(V3_MAIL_DATA) != 0xAA || - v3_readb(V3_MAIL_DATA + 4) != 0x55); - - /* Make sure that V3 register access is not locked, if it is, unlock it */ - if (v3_readw(V3_SYSTEM) & V3_SYSTEM_M_LOCK) - v3_writew(V3_SYSTEM, 0xA05F); - - /* - * Ensure that the slave accesses from PCI are disabled while we - * setup memory windows - */ - val = v3_readw(V3_PCI_CMD); - val &= ~(V3_COMMAND_M_MEM_EN | V3_COMMAND_M_IO_EN); - v3_writew(V3_PCI_CMD, val); - - /* Clear RST_OUT to 0; keep the PCI bus in reset until we've finished */ - val = v3_readw(V3_SYSTEM); - val &= ~V3_SYSTEM_M_RST_OUT; - v3_writew(V3_SYSTEM, val); - - /* Make all accesses from PCI space retry until we're ready for them */ - val = v3_readw(V3_PCI_CFG); - val |= V3_PCI_CFG_M_RETRY_EN; - v3_writew(V3_PCI_CFG, val); - - /* - * Set up any V3 PCI Configuration Registers that we absolutely have to. - * LB_CFG controls Local Bus protocol. - * Enable LocalBus byte strobes for READ accesses too. - * set bit 7 BE_IMODE and bit 6 BE_OMODE - */ - val = v3_readw(V3_LB_CFG); - val |= 0x0C0; - v3_writew(V3_LB_CFG, val); - - /* PCI_CMD controls overall PCI operation. Enable PCI bus master. */ - val = v3_readw(V3_PCI_CMD); - val |= V3_COMMAND_M_MASTER_EN; - v3_writew(V3_PCI_CMD, val); - - /* - * PCI_MAP0 controls where the PCI to CPU memory window is on - * Local Bus - */ - v3_writel(V3_PCI_MAP0, - (INTEGRATOR_BOOT_ROM_BASE) | (V3_PCI_MAP_M_ADR_SIZE_512MB | - V3_PCI_MAP_M_REG_EN | - V3_PCI_MAP_M_ENABLE)); - - /* PCI_BASE0 is the PCI address of the start of the window */ - v3_writel(V3_PCI_BASE0, INTEGRATOR_BOOT_ROM_BASE); - - /* PCI_MAP1 is LOCAL address of the start of the window */ - v3_writel(V3_PCI_MAP1, - (INTEGRATOR_HDR0_SDRAM_BASE) | (V3_PCI_MAP_M_ADR_SIZE_1GB | - V3_PCI_MAP_M_REG_EN | - V3_PCI_MAP_M_ENABLE)); - - /* PCI_BASE1 is the PCI address of the start of the window */ - v3_writel(V3_PCI_BASE1, INTEGRATOR_HDR0_SDRAM_BASE); - - /* - * Set up memory the windows from local bus memory into PCI - * configuration, I/O and Memory regions. - * PCI I/O, LB_BASE2 and LB_MAP2 are used exclusively for this. - */ - v3_writew(V3_LB_BASE2, - v3_addr_to_lb_map(PHYS_PCI_IO_BASE) | V3_LB_BASE_ENABLE); - v3_writew(V3_LB_MAP2, 0); - - /* PCI Configuration, use LB_BASE1/LB_MAP1. */ - - /* - * PCI Memory use LB_BASE0/LB_MAP0 and LB_BASE1/LB_MAP1 - * Map first 256Mbytes as non-prefetchable via BASE0/MAP0 - */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | - V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE); - v3_writew(V3_LB_MAP0, - v3_addr_to_lb_map(PCI_BUS_NONMEM_START) | V3_LB_MAP_TYPE_MEM); - - /* Map second 256 Mbytes as prefetchable via BASE1/MAP1 */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE + SZ_256M) | - V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH | - V3_LB_BASE_ENABLE); - v3_writew(V3_LB_MAP1, v3_addr_to_lb_map(PCI_BUS_PREMEM_START) | - V3_LB_MAP_TYPE_MEM_MULTIPLE); - - /* Dump PCI to local address space mappings */ - debug("LB_BASE0 = %08x\n", v3_readl(V3_LB_BASE0)); - debug("LB_MAP0 = %04x\n", v3_readw(V3_LB_MAP0)); - debug("LB_BASE1 = %08x\n", v3_readl(V3_LB_BASE1)); - debug("LB_MAP1 = %04x\n", v3_readw(V3_LB_MAP1)); - debug("LB_BASE2 = %04x\n", v3_readw(V3_LB_BASE2)); - debug("LB_MAP2 = %04x\n", v3_readw(V3_LB_MAP2)); - debug("LB_IO_BASE = %04x\n", v3_readw(V3_LB_IO_BASE)); - - /* - * Allow accesses to PCI Configuration space and set up A1, A0 for - * type 1 config cycles - */ - val = v3_readw(V3_PCI_CFG); - val &= ~(V3_PCI_CFG_M_RETRY_EN | V3_PCI_CFG_M_AD_LOW1); - val |= V3_PCI_CFG_M_AD_LOW0; - v3_writew(V3_PCI_CFG, val); - - /* now we can allow incoming PCI MEMORY accesses */ - val = v3_readw(V3_PCI_CMD); - val |= V3_COMMAND_M_MEM_EN; - v3_writew(V3_PCI_CMD, val); - - /* - * Set RST_OUT to take the PCI bus is out of reset, PCI devices can - * now initialise. - */ - val = v3_readw(V3_SYSTEM); - val |= V3_SYSTEM_M_RST_OUT; - v3_writew(V3_SYSTEM, val); - - /* Lock the V3 system register so that no one else can play with it */ - val = v3_readw(V3_SYSTEM); - val |= V3_SYSTEM_M_LOCK; - v3_writew(V3_SYSTEM, val); - - /* - * Configure and register the PCI hose - */ - hose->first_busno = 0; - hose->last_busno = 0xff; - - /* System memory space, window 0 256 MB non-prefetchable */ - pci_set_region(hose->regions + 0, - PCI_BUS_NONMEM_START, PHYS_PCI_MEM_BASE, - SZ_256M, - PCI_REGION_MEM); - - /* System memory space, window 1 256 MB prefetchable */ - pci_set_region(hose->regions + 1, - PCI_BUS_PREMEM_START, PHYS_PCI_MEM_BASE + SZ_256M, - SZ_256M, - PCI_REGION_MEM | - PCI_REGION_PREFETCH); - - /* PCI I/O space */ - pci_set_region(hose->regions + 2, - 0x00000000, PHYS_PCI_IO_BASE, 0x01000000, - PCI_REGION_IO); - - /* PCI Memory - config space */ - pci_set_region(hose->regions + 3, - 0x00000000, PHYS_PCI_CONFIG_BASE, 0x01000000, - PCI_REGION_MEM); - /* PCI V3 regs */ - pci_set_region(hose->regions + 4, - 0x00000000, PHYS_PCI_V3_BASE, 0x01000000, - PCI_REGION_MEM); - - hose->region_count = 5; - - pci_set_ops(hose, - pci_integrator_read_byte, - pci_integrator_read__word, - pci_integrator_read_dword, - pci_integrator_write_byte, - pci_integrator_write_word, - pci_integrator_write_dword); - - pci_register_hose(hose); - - pciauto_config_init(hose); - pciauto_config_device(hose, 0); - - hose->last_busno = pci_hose_scan(hose); -} diff --git a/board/armltd/integrator/pci_v3.h b/board/armltd/integrator/pci_v3.h deleted file mode 100644 index 8d09e6966db2..000000000000 --- a/board/armltd/integrator/pci_v3.h +++ /dev/null @@ -1,187 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * arch/arm/include/asm/hardware/pci_v3.h - * - * Internal header file PCI V3 chip - * - * Copyright (C) ARM Limited - * Copyright (C) 2000-2001 Deep Blue Solutions Ltd. - */ -#ifndef ASM_ARM_HARDWARE_PCI_V3_H -#define ASM_ARM_HARDWARE_PCI_V3_H - -/* ------------------------------------------------------------------------------- - * V3 Local Bus to PCI Bridge definitions - * ------------------------------------------------------------------------------- - * Registers (these are taken from page 129 of the EPC User's Manual Rev 1.04 - * All V3 register names are prefaced by V3_ to avoid clashing with any other - * PCI definitions. Their names match the user's manual. - * - * I'm assuming that I20 is disabled. - * - */ -#define V3_PCI_VENDOR 0x00000000 -#define V3_PCI_DEVICE 0x00000002 -#define V3_PCI_CMD 0x00000004 -#define V3_PCI_STAT 0x00000006 -#define V3_PCI_CC_REV 0x00000008 -#define V3_PCI_HDR_CFG 0x0000000C -#define V3_PCI_IO_BASE 0x00000010 -#define V3_PCI_BASE0 0x00000014 -#define V3_PCI_BASE1 0x00000018 -#define V3_PCI_SUB_VENDOR 0x0000002C -#define V3_PCI_SUB_ID 0x0000002E -#define V3_PCI_ROM 0x00000030 -#define V3_PCI_BPARAM 0x0000003C -#define V3_PCI_MAP0 0x00000040 -#define V3_PCI_MAP1 0x00000044 -#define V3_PCI_INT_STAT 0x00000048 -#define V3_PCI_INT_CFG 0x0000004C -#define V3_LB_BASE0 0x00000054 -#define V3_LB_BASE1 0x00000058 -#define V3_LB_MAP0 0x0000005E -#define V3_LB_MAP1 0x00000062 -#define V3_LB_BASE2 0x00000064 -#define V3_LB_MAP2 0x00000066 -#define V3_LB_SIZE 0x00000068 -#define V3_LB_IO_BASE 0x0000006E -#define V3_FIFO_CFG 0x00000070 -#define V3_FIFO_PRIORITY 0x00000072 -#define V3_FIFO_STAT 0x00000074 -#define V3_LB_ISTAT 0x00000076 -#define V3_LB_IMASK 0x00000077 -#define V3_SYSTEM 0x00000078 -#define V3_LB_CFG 0x0000007A -#define V3_PCI_CFG 0x0000007C -#define V3_DMA_PCI_ADR0 0x00000080 -#define V3_DMA_PCI_ADR1 0x00000090 -#define V3_DMA_LOCAL_ADR0 0x00000084 -#define V3_DMA_LOCAL_ADR1 0x00000094 -#define V3_DMA_LENGTH0 0x00000088 -#define V3_DMA_LENGTH1 0x00000098 -#define V3_DMA_CSR0 0x0000008B -#define V3_DMA_CSR1 0x0000009B -#define V3_DMA_CTLB_ADR0 0x0000008C -#define V3_DMA_CTLB_ADR1 0x0000009C -#define V3_DMA_DELAY 0x000000E0 -#define V3_MAIL_DATA 0x000000C0 -#define V3_PCI_MAIL_IEWR 0x000000D0 -#define V3_PCI_MAIL_IERD 0x000000D2 -#define V3_LB_MAIL_IEWR 0x000000D4 -#define V3_LB_MAIL_IERD 0x000000D6 -#define V3_MAIL_WR_STAT 0x000000D8 -#define V3_MAIL_RD_STAT 0x000000DA -#define V3_QBA_MAP 0x000000DC - -/* PCI COMMAND REGISTER bits - */ -#define V3_COMMAND_M_FBB_EN (1 << 9) -#define V3_COMMAND_M_SERR_EN (1 << 8) -#define V3_COMMAND_M_PAR_EN (1 << 6) -#define V3_COMMAND_M_MASTER_EN (1 << 2) -#define V3_COMMAND_M_MEM_EN (1 << 1) -#define V3_COMMAND_M_IO_EN (1 << 0) - -/* SYSTEM REGISTER bits - */ -#define V3_SYSTEM_M_RST_OUT (1 << 15) -#define V3_SYSTEM_M_LOCK (1 << 14) - -/* PCI_CFG bits - */ -#define V3_PCI_CFG_M_I2O_EN (1 << 15) -#define V3_PCI_CFG_M_IO_REG_DIS (1 << 14) -#define V3_PCI_CFG_M_IO_DIS (1 << 13) -#define V3_PCI_CFG_M_EN3V (1 << 12) -#define V3_PCI_CFG_M_RETRY_EN (1 << 10) -#define V3_PCI_CFG_M_AD_LOW1 (1 << 9) -#define V3_PCI_CFG_M_AD_LOW0 (1 << 8) - -/* PCI_BASE register bits (PCI -> Local Bus) - */ -#define V3_PCI_BASE_M_ADR_BASE 0xFFF00000 -#define V3_PCI_BASE_M_ADR_BASEL 0x000FFF00 -#define V3_PCI_BASE_M_PREFETCH (1 << 3) -#define V3_PCI_BASE_M_TYPE (3 << 1) -#define V3_PCI_BASE_M_IO (1 << 0) - -/* PCI MAP register bits (PCI -> Local bus) - */ -#define V3_PCI_MAP_M_MAP_ADR 0xFFF00000 -#define V3_PCI_MAP_M_RD_POST_INH (1 << 15) -#define V3_PCI_MAP_M_ROM_SIZE (3 << 10) -#define V3_PCI_MAP_M_SWAP (3 << 8) -#define V3_PCI_MAP_M_ADR_SIZE 0x000000F0 -#define V3_PCI_MAP_M_REG_EN (1 << 1) -#define V3_PCI_MAP_M_ENABLE (1 << 0) - -#define V3_PCI_MAP_M_ADR_SIZE_1MB (0 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_2MB (1 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_4MB (2 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_8MB (3 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_16MB (4 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_32MB (5 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_64MB (6 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_128MB (7 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_256MB (8 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_512MB (9 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_1GB (10 << 4) -#define V3_PCI_MAP_M_ADR_SIZE_2GB (11 << 4) - -/* - * LB_BASE0,1 register bits (Local bus -> PCI) - */ -#define V3_LB_BASE_ADR_BASE 0xfff00000 -#define V3_LB_BASE_SWAP (3 << 8) -#define V3_LB_BASE_ADR_SIZE (15 << 4) -#define V3_LB_BASE_PREFETCH (1 << 3) -#define V3_LB_BASE_ENABLE (1 << 0) - -#define V3_LB_BASE_ADR_SIZE_1MB (0 << 4) -#define V3_LB_BASE_ADR_SIZE_2MB (1 << 4) -#define V3_LB_BASE_ADR_SIZE_4MB (2 << 4) -#define V3_LB_BASE_ADR_SIZE_8MB (3 << 4) -#define V3_LB_BASE_ADR_SIZE_16MB (4 << 4) -#define V3_LB_BASE_ADR_SIZE_32MB (5 << 4) -#define V3_LB_BASE_ADR_SIZE_64MB (6 << 4) -#define V3_LB_BASE_ADR_SIZE_128MB (7 << 4) -#define V3_LB_BASE_ADR_SIZE_256MB (8 << 4) -#define V3_LB_BASE_ADR_SIZE_512MB (9 << 4) -#define V3_LB_BASE_ADR_SIZE_1GB (10 << 4) -#define V3_LB_BASE_ADR_SIZE_2GB (11 << 4) - -#define v3_addr_to_lb_base(a) ((a) & V3_LB_BASE_ADR_BASE) - -/* - * LB_MAP0,1 register bits (Local bus -> PCI) - */ -#define V3_LB_MAP_MAP_ADR 0xfff0 -#define V3_LB_MAP_TYPE (7 << 1) -#define V3_LB_MAP_AD_LOW_EN (1 << 0) - -#define V3_LB_MAP_TYPE_IACK (0 << 1) -#define V3_LB_MAP_TYPE_IO (1 << 1) -#define V3_LB_MAP_TYPE_MEM (3 << 1) -#define V3_LB_MAP_TYPE_CONFIG (5 << 1) -#define V3_LB_MAP_TYPE_MEM_MULTIPLE (6 << 1) - -/* PCI MAP register bits (PCI -> Local bus) */ -#define v3_addr_to_lb_map(a) (((a) >> 16) & V3_LB_MAP_MAP_ADR) - -/* - * LB_BASE2 register bits (Local bus -> PCI IO) - */ -#define V3_LB_BASE2_ADR_BASE 0xff00 -#define V3_LB_BASE2_SWAP (3 << 6) -#define V3_LB_BASE2_ENABLE (1 << 0) - -#define v3_addr_to_lb_base2(a) (((a) >> 16) & V3_LB_BASE2_ADR_BASE) - -/* - * LB_MAP2 register bits (Local bus -> PCI IO) - */ -#define V3_LB_MAP2_MAP_ADR 0xff00 - -#define v3_addr_to_lb_map2(a) (((a) >> 16) & V3_LB_MAP2_MAP_ADR) - -#endif diff --git a/configs/integratorap_cm720t_defconfig b/configs/integratorap_cm720t_defconfig index 5d28135a8220..378bf936d737 100644 --- a/configs/integratorap_cm720t_defconfig +++ b/configs/integratorap_cm720t_defconfig @@ -16,7 +16,6 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Integrator-AP # " CONFIG_CMD_IMLS=y CONFIG_CMD_ARMFLASH=y -CONFIG_CMD_PCI=y # CONFIG_CMD_SETEXPR is not set CONFIG_SYS_RELOC_GD_ENV_ADDR=y # CONFIG_MMC is not set @@ -24,8 +23,5 @@ CONFIG_MTD_NOR_FLASH=y CONFIG_FLASH_CFI_DRIVER=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y -CONFIG_EEPRO100=y -CONFIG_TULIP=y -CONFIG_PCI=y CONFIG_BAUDRATE=38400 CONFIG_OF_LIBFDT=y diff --git a/configs/integratorap_cm920t_defconfig b/configs/integratorap_cm920t_defconfig index 0e914e91ebed..4ec2961a4ecb 100644 --- a/configs/integratorap_cm920t_defconfig +++ b/configs/integratorap_cm920t_defconfig @@ -16,7 +16,6 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Integrator-AP # " CONFIG_CMD_IMLS=y CONFIG_CMD_ARMFLASH=y -CONFIG_CMD_PCI=y # CONFIG_CMD_SETEXPR is not set CONFIG_SYS_RELOC_GD_ENV_ADDR=y # CONFIG_MMC is not set @@ -24,8 +23,5 @@ CONFIG_MTD_NOR_FLASH=y CONFIG_FLASH_CFI_DRIVER=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y -CONFIG_EEPRO100=y -CONFIG_TULIP=y -CONFIG_PCI=y CONFIG_BAUDRATE=38400 CONFIG_OF_LIBFDT=y diff --git a/configs/integratorap_cm926ejs_defconfig b/configs/integratorap_cm926ejs_defconfig index d28bc0f976cf..012d346500f5 100644 --- a/configs/integratorap_cm926ejs_defconfig +++ b/configs/integratorap_cm926ejs_defconfig @@ -16,7 +16,6 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Integrator-AP # " CONFIG_CMD_IMLS=y CONFIG_CMD_ARMFLASH=y -CONFIG_CMD_PCI=y # CONFIG_CMD_SETEXPR is not set CONFIG_SYS_RELOC_GD_ENV_ADDR=y # CONFIG_MMC is not set @@ -24,8 +23,5 @@ CONFIG_MTD_NOR_FLASH=y CONFIG_FLASH_CFI_DRIVER=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y -CONFIG_EEPRO100=y -CONFIG_TULIP=y -CONFIG_PCI=y CONFIG_BAUDRATE=38400 CONFIG_OF_LIBFDT=y diff --git a/configs/integratorap_cm946es_defconfig b/configs/integratorap_cm946es_defconfig index ae44f01ff50d..1868c7024f0f 100644 --- a/configs/integratorap_cm946es_defconfig +++ b/configs/integratorap_cm946es_defconfig @@ -16,7 +16,6 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Integrator-AP # " CONFIG_CMD_IMLS=y CONFIG_CMD_ARMFLASH=y -CONFIG_CMD_PCI=y # CONFIG_CMD_SETEXPR is not set CONFIG_SYS_RELOC_GD_ENV_ADDR=y # CONFIG_MMC is not set @@ -24,8 +23,5 @@ CONFIG_MTD_NOR_FLASH=y CONFIG_FLASH_CFI_DRIVER=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y -CONFIG_EEPRO100=y -CONFIG_TULIP=y -CONFIG_PCI=y CONFIG_BAUDRATE=38400 CONFIG_OF_LIBFDT=y