Hi Fabio
On 24.06.20 21:39, Fabio Estevam wrote:
Hi Soeren,
On Wed, Jun 24, 2020 at 4:20 PM Soeren Moch smoch@web.de wrote:
I tested current master (v2020.07-rc5 + imx fixes) on tbs2910 (imx6q + atheros PHY). Unfortunately ethernet is broken now, while it used to work well on u-boot version v2020.04. Ethernet support was copied from imx6q-sabresd, the recently for sabresd fixed phy-mode already is rgmii-id for tbs2910.
Any ideas what could be wrong?
I just tested mainline U-Boot and Ethernet works fine on a imx6qp sabresd board:
U-Boot SPL 2020.07-rc5-00052-g922c6d5d00 (Jun 24 2020 - 16:21:27 -0300) Trying to boot from MMC1
U-Boot 2020.07-rc5-00052-g922c6d5d00 (Jun 24 2020 - 16:21:27 -0300)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 30C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3 Loading Environment from MMC... OK No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial Net: eth0: ethernet@2188000 Hit any key to stop autoboot: 0 => dhcp zImage BOOTP broadcast 1 DHCP client bound to address 192.168.0.24 (50 ms) Using ethernet@2188000 device TFTP from server 192.168.0.12; our IP address is 192.168.0.24 Filename 'zImage'. Load address: 0x12000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 1.3 MiB/s done Bytes transferred = 9468928 (907c00 hex) => mdio list FEC0: 1 - AR8031/AR8033 <--> ethernet@2188000 =>
What is the exact failure you see? Is the Ethernet PHY found at the correct address and probed?
From what I see nothing is obviously wrong, just no ethernet connection:
U-Boot 2020.07-rc5-00039-g4ff63383e3-dirty (Jun 24 2020 - 21:48:31 +0200)
CPU: Freescale i.MX6Q rev1.2 at 792MHz CPU: Commercial temperature grade (0C to 95C) at 42C Reset cause: POR Model: TBS2910 Matrix ARM mini PC DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK No panel detected: default to HDMI Display: HDMI (1024x768) In: serial Out: vga Err: vga Net: eth0: ethernet@2188000 PCI:
PCI: pcie phy link never came up No such bus starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 4 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 Matrix U-Boot> dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 BOOTP broadcast 8 BOOTP broadcast 9 BOOTP broadcast 10 BOOTP broadcast 11 BOOTP broadcast 12 BOOTP broadcast 13 BOOTP broadcast 14 BOOTP broadcast 15 BOOTP broadcast 16 BOOTP broadcast 17
Retry time exceeded; starting again Matrix U-Boot> mdio list FEC0:
4 - AR8035 <--> ethernet@2188000 Matrix U-Boot>
On tbs2910 does the AR8031 generate a 125MHz clock to the i.MX6Q Ethernet?
If so, does the change below help (I am assuming the PHY is located at address 1, if not, please adjust the @ and reg accordingly)?
--- a/arch/arm/dts/imx6q-tbs2910.dts +++ b/arch/arm/dts/imx6q-tbs2910.dts @@ -108,6 +108,16 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; status = "okay";
mdio {#address-cells = <1>;#size-cells = <0>;phy: ethernet-phy@1 {reg = <1>;qca,clk-out-frequency = <125000000>;};};};
I used this patch with address 4 (that's why the -dirty in the u-boot version), no luck. It seems I have a AR8035 PHY.
In case you still have issues, please share the tbs2910 schematics with me offline so I can try to understand the failure.
Schematics are at https://www.tbsdtv.com/download/document/tbs2910/TBS2910-Matrix-ARM-mini-PC-...
Thanks for your help, Soeren