From: Chris Morgan macromorgan@hotmail.com
Changes from v2: - Resending due to glitch with patch file truncating final two lines on patch 1/5 and incorrect patch version number on patch 5/5.
Changes from v1: - Reworked code to utilize spi-mem framework, and based it closely off of work in progress code for mainline Linux. - Removed DMA, as it didn't offer much performance benefit for booting (in my test cases), added complexity to the code, and interfered with A-TF. - Updated the names of the bindings to match the work in progress Linux code. - Moved alias to u-boot specific device-tree for Odroid Go Advance. Alias is updated with the spi0 node pointing to the SFC to help the sf command as well as facilitate booting from the SFC. - Note 2 below no longer applies, as rebasing this off of upstream code should allow the device to work for NAND, and by utilizing the spi-mem framework it no longer has to extract the parameters from the dm_spi_ops.xfer.
Requesting comments for a proposed patchset for adding the Rockchip serial flash controller to u-boot. The goal of these patches is to enable it for the Odroid Go Advance so that it may eventually boot exclusively from the SFC on mainline U-boot (I have tested this and it works).
The specific help I need with this patch is:
1) I don't know the best way to upstream the XTX25F128B flash chip. This chip uses a continuation code for the manufacturer ID, however I cannot seem to find any way to actually read the continuation code. There is a risk of this driver, used as-is, to collide with another chip which has the same manufacturer ID with a different continuation code.
2) The Rockchip SFC driver itself (as it is mostly as-is from the BSP U-Boot sources) supports SPI NAND and chips of varying sizes, but my implementation only permits me to test with a single 128Mb flash chip. The driver itself does some checking on the bitlen in the routine rockchip_sfc_xfer() which is what is called for the dm_spi_ops.xfer. I'm not sure if there is a better way to do this. Additionally, I have to bit-shift the address written to the SFC as I suspect the value is meant to be left justified, but I never tested it further.
Additionally, it might be worth mentioning but I noticed the Rockchip BROM will only boot the TPL/SPL off of the SFC if I write it to address 0x10000. This is not documented and different than the address looked at for SD card booting (512 * 64 = 0x8000 for SD Card booting). Also, like the SD card driver I can confirm that if DMA is enabled at the SPL stage A-TF seems to fail silently, then when Linux loads it hangs. There is an ifdef to force FIFO mode only in the SPL stage.
Tested: Read (works) Write (works if you write to an erased sector) Erase (works) SPL Read (works if you edit the u-boot,spl-boot-order)
Chris Morgan (5): spi: rockchip_sfc: add support for Rockchip SFC rockchip: px30: Add support for using SFC rockchip: px30: add the serial flash controller mtd: spi-nor-ids: Add XTX XT25F128B rockchip: px30: add support for SFC for Odroid Go Advance
arch/arm/dts/px30.dtsi | 38 ++ arch/arm/dts/rk3326-odroid-go2-u-boot.dtsi | 17 + arch/arm/dts/rk3326-odroid-go2.dts | 16 + arch/arm/mach-rockchip/px30/px30.c | 64 +++ drivers/mtd/spi/Kconfig | 6 + drivers/mtd/spi/spi-nor-ids.c | 8 + drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/rockchip_sfc.c | 495 +++++++++++++++++++++ 9 files changed, 653 insertions(+) create mode 100644 drivers/spi/rockchip_sfc.c