u-boot standard i2c register write prototype is i2c_reg_write(u8 addr, u8 reg, u8 val)
twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val)
Signed-off-by: Nishanth Menon nm@ti.com --- board/cm_t35/cm_t35.c | 20 +++++++++---------- board/nokia/rx51/rx51.c | 36 +++++++++++++++++----------------- board/pandora/pandora.c | 3 ++- drivers/misc/twl4030_led.c | 4 ++-- drivers/power/twl4030.c | 12 ++++++------ drivers/usb/phy/twl4030.c | 46 ++++++++++++++++++++++---------------------- include/twl4030.h | 2 +- 7 files changed, 62 insertions(+), 61 deletions(-)
diff --git a/board/cm_t35/cm_t35.c b/board/cm_t35/cm_t35.c index e0e8235..a14f89f 100644 --- a/board/cm_t35/cm_t35.c +++ b/board/cm_t35/cm_t35.c @@ -430,17 +430,17 @@ static void setup_net_chip_gmpc(void) static void reset_net_chip(void) { /* Set GPIO1 of TPS65930 as output */ - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02, - TWL4030_BASEADD_GPIO + 0x03); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x03, + 0x02); /* Send a pulse on the GPIO pin */ - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02, - TWL4030_BASEADD_GPIO + 0x0C); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C, + 0x02); udelay(1); - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02, - TWL4030_BASEADD_GPIO + 0x09); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x09, + 0x02); mdelay(40); - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02, - TWL4030_BASEADD_GPIO + 0x0C); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C, + 0x02); mdelay(1); } #else @@ -537,10 +537,10 @@ int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor) twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, offset); /* Set GPIO6 and GPIO7 of TPS65930 as output */ val |= 0xC0; - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, val, offset); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, val); offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_SETGPIODATAOUT1; /* Take both PHYs out of reset */ - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0xC0, offset); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, 0xC0); udelay(1);
return omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor); diff --git a/board/nokia/rx51/rx51.c b/board/nokia/rx51/rx51.c index 48eb65f..464302b 100644 --- a/board/nokia/rx51/rx51.c +++ b/board/nokia/rx51/rx51.c @@ -332,10 +332,10 @@ void *video_hw_init(void) static void twl4030_regulator_set_mode(u8 id, u8 mode) { u16 msg = MSG_SINGULAR(DEV_GRP_P1, id, mode); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, msg >> 8, - TWL4030_PM_MASTER_PB_WORD_MSB); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, msg & 0xff, - TWL4030_PM_MASTER_PB_WORD_LSB); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PB_WORD_MSB, msg >> 8); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PB_WORD_LSB, msg & 0xff); }
static void omap3_emu_romcode_call(u32 service_id, u32 *parameters) @@ -410,8 +410,8 @@ int misc_init_r(void) TWL4030_PM_MASTER_PB_CFG);
/* enable I2C access to powerbus (needed for twl4030 regulator) */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x02, - TWL4030_PM_MASTER_PB_CFG); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG, + 0x02);
/* set VAUX3, VSIM and VMMC1 state to active - enable eMMC memory */ twl4030_regulator_set_mode(RES_VAUX3, RES_STATE_ACTIVE); @@ -419,8 +419,8 @@ int misc_init_r(void) twl4030_regulator_set_mode(RES_VMMC1, RES_STATE_ACTIVE);
/* restore I2C access state */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, state, - TWL4030_PM_MASTER_PB_CFG); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG, + state);
/* set env variable attkernaddr for relocated kernel */ sprintf(buf, "%#x", KERNEL_ADDRESS); @@ -481,8 +481,8 @@ void hw_watchdog_reset(void) /* timeout 0 means watchdog is disabled */ /* reset watchdog timeout to 31s (maximum) */ if (timeout != 0) - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 31, - TWL4030_PM_RECEIVER_WATCHDOG_CFG); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_WATCHDOG_CFG, 31);
/* store last watchdog reset time */ twl_wd_time = get_timer(0); @@ -541,18 +541,18 @@ int rx51_kp_init(void) ctrl |= TWL4030_KEYPAD_CTRL_KBD_ON; ctrl |= TWL4030_KEYPAD_CTRL_SOFT_NRST; ctrl |= TWL4030_KEYPAD_CTRL_SOFTMODEN; - ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, ctrl, - TWL4030_KEYPAD_KEYP_CTRL_REG); + ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_CTRL_REG, ctrl); /* enable key event status */ - ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0xfe, - TWL4030_KEYPAD_KEYP_IMR1); + ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_IMR1, 0xfe); /* enable interrupt generation on rising and falling */ /* this is a workaround for qemu twl4030 emulation */ - ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0x57, - TWL4030_KEYPAD_KEYP_EDR); + ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_EDR, 0x57); /* enable ISR clear on read */ - ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0x05, - TWL4030_KEYPAD_KEYP_SIH_CTRL); + ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_SIH_CTRL, 0x05); return 0; }
diff --git a/board/pandora/pandora.c b/board/pandora/pandora.c index 9ff5dd7..5f0c58d 100644 --- a/board/pandora/pandora.c +++ b/board/pandora/pandora.c @@ -114,8 +114,9 @@ int misc_init_r(void)
/* Enable battery backup capacitor (3.2V, 0.5mA charge current) */ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_BB_CFG, TWL4030_BB_CFG_BBCHEN | TWL4030_BB_CFG_BBSEL_3200MV | - TWL4030_BB_CFG_BBISEL_500UA, TWL4030_PM_RECEIVER_BB_CFG); + TWL4030_BB_CFG_BBISEL_500UA);
dieid_num_r();
diff --git a/drivers/misc/twl4030_led.c b/drivers/misc/twl4030_led.c index 33cea11..e150d8f 100644 --- a/drivers/misc/twl4030_led.c +++ b/drivers/misc/twl4030_led.c @@ -42,7 +42,7 @@ void twl4030_led_init(unsigned char ledon_mask) if (ledon_mask & TWL4030_LED_LEDEN_LEDBON) ledon_mask |= TWL4030_LED_LEDEN_LEDBPWM;
- twl4030_i2c_write_u8(TWL4030_CHIP_LED, ledon_mask, - TWL4030_LED_LEDEN); + twl4030_i2c_write_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN, + ledon_mask);
} diff --git a/drivers/power/twl4030.c b/drivers/power/twl4030.c index e7d5f13..3e933e9 100644 --- a/drivers/power/twl4030.c +++ b/drivers/power/twl4030.c @@ -51,8 +51,8 @@ void twl4030_power_reset_init(void) printf("Could not initialize hardware reset\n"); } else { val |= TWL4030_PM_MASTER_SW_EVENTS_STOPON_PWRON; - if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, val, - TWL4030_PM_MASTER_P1_SW_EVENTS)) { + if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_P1_SW_EVENTS, val)) { printf("Error:TWL4030: failed to write the power register\n"); printf("Could not initialize hardware reset\n"); } @@ -68,8 +68,8 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val, int ret;
/* Select the Voltage */ - ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_val, - vsel_reg); + ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_reg, + vsel_val); if (ret != 0) { printf("Could not write vsel to reg %02x (%d)\n", vsel_reg, ret); @@ -77,8 +77,8 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val, }
/* Select the Device Group (enable the supply if dev_grp_sel != 0) */ - ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp_sel, - dev_grp); + ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp, + dev_grp_sel); if (ret != 0) printf("Could not write grp_sel to reg %02x (%d)\n", dev_grp, ret); diff --git a/drivers/usb/phy/twl4030.c b/drivers/usb/phy/twl4030.c index 54d2e61..f41cc07 100644 --- a/drivers/usb/phy/twl4030.c +++ b/drivers/usb/phy/twl4030.c @@ -54,7 +54,7 @@ static int twl4030_usb_write(u8 address, u8 data) { int ret;
- ret = twl4030_i2c_write_u8(TWL4030_CHIP_USB, data, address); + ret = twl4030_i2c_write_u8(TWL4030_CHIP_USB, address, data); if (ret != 0) printf("TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
@@ -78,40 +78,40 @@ static int twl4030_usb_read(u8 address) static void twl4030_usb_ldo_init(void) { /* Enable writing to power configuration registers */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0xC0, - TWL4030_PM_MASTER_PROTECT_KEY); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x0C, - TWL4030_PM_MASTER_PROTECT_KEY); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PROTECT_KEY, 0xC0); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PROTECT_KEY, 0x0C);
/* put VUSB3V1 LDO in active state */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00, - TWL4030_PM_RECEIVER_VUSB_DEDICATED2); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB_DEDICATED2, 0x00);
/* input to VUSB3V1 LDO is from VBAT, not VBUS */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x14, - TWL4030_PM_RECEIVER_VUSB_DEDICATED1); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB_DEDICATED1, 0x14);
/* turn on 3.1V regulator */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20, - TWL4030_PM_RECEIVER_VUSB3V1_DEV_GRP); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00, - TWL4030_PM_RECEIVER_VUSB3V1_TYPE); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB3V1_DEV_GRP, 0x20); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB3V1_TYPE, 0x00);
/* turn on 1.5V regulator */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20, - TWL4030_PM_RECEIVER_VUSB1V5_DEV_GRP); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00, - TWL4030_PM_RECEIVER_VUSB1V5_TYPE); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB1V5_DEV_GRP, 0x20); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB1V5_TYPE, 0x00);
/* turn on 1.8V regulator */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20, - TWL4030_PM_RECEIVER_VUSB1V8_DEV_GRP); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00, - TWL4030_PM_RECEIVER_VUSB1V8_TYPE); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB1V8_DEV_GRP, 0x20); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB1V8_TYPE, 0x00);
/* disable access to power configuration registers */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x00, - TWL4030_PM_MASTER_PROTECT_KEY); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PROTECT_KEY, 0x00); }
static void twl4030_phy_power(void) diff --git a/include/twl4030.h b/include/twl4030.h index 5aa1841..aca695d 100644 --- a/include/twl4030.h +++ b/include/twl4030.h @@ -638,7 +638,7 @@ * examples are TWL4030_PM_RECEIVER_VMMC1_DEV_GRP and * TWL4030_LED_LEDEN. */ -static inline int twl4030_i2c_write_u8(u8 chip_no, u8 val, u8 reg) +static inline int twl4030_i2c_write_u8(u8 chip_no, u8 reg, u8 val) { return i2c_write(chip_no, reg, 1, &val, 1); }