TPS62361 is the new power supply used in OMAP4460 that supplies vdd_mpu.
VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies vdd_iva. VCORE3 is not used in OMAP4460.
Signed-off-by: Aneesh V aneesh@ti.com --- arch/arm/cpu/armv7/omap4/board.c | 4 ++ arch/arm/cpu/armv7/omap4/clocks.c | 65 ++++++++++++++++++++++++--- arch/arm/include/asm/arch-omap4/clocks.h | 16 +++++++ arch/arm/include/asm/arch-omap4/mux_omap4.h | 1 + 4 files changed, 79 insertions(+), 7 deletions(-)
diff --git a/arch/arm/cpu/armv7/omap4/board.c b/arch/arm/cpu/armv7/omap4/board.c index 3c61b1c..5943d61 100644 --- a/arch/arm/cpu/armv7/omap4/board.c +++ b/arch/arm/cpu/armv7/omap4/board.c @@ -90,6 +90,10 @@ static void set_muxconf_regs_essential(void) do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_essential, sizeof(wkup_padconf_array_essential) / sizeof(struct pad_conf_entry)); + + /* gpio_wk7 is used for controlling TPS on 4460 */ + if (omap_revision() >= OMAP4460_ES1_0) + writew(M3, CONTROL_WKUP_PAD1_FREF_CLK4_REQ); }
static void set_mux_conf_regs(void) diff --git a/arch/arm/cpu/armv7/omap4/clocks.c b/arch/arm/cpu/armv7/omap4/clocks.c index 660b329..0db9d18 100644 --- a/arch/arm/cpu/armv7/omap4/clocks.c +++ b/arch/arm/cpu/armv7/omap4/clocks.c @@ -34,6 +34,7 @@ #include <asm/arch/clocks.h> #include <asm/arch/sys_proto.h> #include <asm/utils.h> +#include <asm/omap_gpio.h>
#ifndef CONFIG_SPL_BUILD /* @@ -421,6 +422,34 @@ static void setup_non_essential_dplls(void) do_setup_dpll(&prcm->cm_clkmode_dpll_abe, params, DPLL_LOCK); }
+static void do_scale_tps62361(u32 reg, u32 volt_mv) +{ + u32 temp, step; + + step = volt_mv - TPS62361_BASE_VOLT_MV; + step /= 10; + + /* + * Select SET1 in TPS62361: + * VSEL1 is grounded on board. So the following selects + * VSEL1 = 0 and VSEL0 = 1 + */ + omap_set_gpio_direction(TPS62361_VSEL0_GPIO, 0); + omap_set_gpio_dataout(TPS62361_VSEL0_GPIO, 1); + + temp = TPS62361_I2C_SLAVE_ADDR | + (reg << PRM_VC_VAL_BYPASS_REGADDR_SHIFT) | + (step << PRM_VC_VAL_BYPASS_DATA_SHIFT) | + PRM_VC_VAL_BYPASS_VALID_BIT; + debug("do_scale_tps62361: volt - %d step - 0x%x\n", volt_mv, step); + + writel(temp, &prcm->prm_vc_val_bypass); + if (!wait_on_value(PRM_VC_VAL_BYPASS_VALID_BIT, 0, + &prcm->prm_vc_val_bypass, LDELAY)) { + puts("Scaling voltage failed for vdd_mpu from TPS\n"); + } +} + static void do_scale_vcore(u32 vcore_reg, u32 volt_mv) { u32 temp, offset_code; @@ -461,7 +490,7 @@ static void do_scale_vcore(u32 vcore_reg, u32 volt_mv) */ static void scale_vcores(void) { - u32 volt, sys_clk_khz, cycles_hi, cycles_low, temp; + u32 volt, sys_clk_khz, cycles_hi, cycles_low, temp, omap4_rev;
sys_clk_khz = get_sys_clk_freq() / 1000;
@@ -481,23 +510,45 @@ static void scale_vcores(void) /* Disable high speed mode and all advanced features */ writel(0x0, &prcm->prm_vc_cfg_i2c_mode);
+ omap4_rev = omap_revision(); + /* TPS - supplies vdd_mpu on 4460 */ + if (omap4_rev >= OMAP4460_ES1_0) { + volt = 1430; + do_scale_tps62361(TPS62361_REG_ADDR_SET1, volt); + } + /* - * VCORE 1 - 4430 : supplies vdd_mpu + * VCORE 1 + * + * 4430 : supplies vdd_mpu * Setting a high voltage for Nitro mode as smart reflex is not enabled. * We use the maximum possible value in the AVS range because the next * higher voltage in the discrete range (code >= 0b111010) is way too * high + * + * 4460 : supplies vdd_core */ - volt = 1417; - do_scale_vcore(SMPS_REG_ADDR_VCORE1, volt); + if (omap4_rev < OMAP4460_ES1_0) { + volt = 1417; + do_scale_vcore(SMPS_REG_ADDR_VCORE1, volt); + } else { + volt = 1200; + do_scale_vcore(SMPS_REG_ADDR_VCORE1, volt); + }
/* VCORE 2 - supplies vdd_iva */ volt = 1200; do_scale_vcore(SMPS_REG_ADDR_VCORE2, volt);
- /* VCORE 3 - supplies vdd_core */ - volt = 1200; - do_scale_vcore(SMPS_REG_ADDR_VCORE3, volt); + /* + * VCORE 3 + * 4430 : supplies vdd_core + * 4460 : not connected + */ + if (omap4_rev < OMAP4460_ES1_0) { + volt = 1200; + do_scale_vcore(SMPS_REG_ADDR_VCORE3, volt); + } }
static inline void enable_clock_domain(u32 *const clkctrl_reg, u32 enable_mode) diff --git a/arch/arm/include/asm/arch-omap4/clocks.h b/arch/arm/include/asm/arch-omap4/clocks.h index 37bdcee..5d9cb50 100644 --- a/arch/arm/include/asm/arch-omap4/clocks.h +++ b/arch/arm/include/asm/arch-omap4/clocks.h @@ -618,6 +618,7 @@ struct omap4_prcm_regs { #define PRM_VC_VAL_BYPASS_DATA_SHIFT 16 #define PRM_VC_VAL_BYPASS_DATA_MASK 0xFF
+/* SMPS */ #define SMPS_I2C_SLAVE_ADDR 0x12 #define SMPS_REG_ADDR_VCORE1 0x55 #define SMPS_REG_ADDR_VCORE2 0x5B @@ -626,6 +627,21 @@ struct omap4_prcm_regs { #define PHOENIX_SMPS_BASE_VOLT_STD_MODE_UV 607700 #define PHOENIX_SMPS_BASE_VOLT_STD_MODE_WITH_OFFSET_UV 709000
+/* TPS */ +#define TPS62361_I2C_SLAVE_ADDR 0x60 +#define TPS62361_REG_ADDR_SET0 0x0 +#define TPS62361_REG_ADDR_SET1 0x1 +#define TPS62361_REG_ADDR_SET2 0x2 +#define TPS62361_REG_ADDR_SET3 0x3 +#define TPS62361_REG_ADDR_CTRL 0x4 +#define TPS62361_REG_ADDR_TEMP 0x5 +#define TPS62361_REG_ADDR_RMP_CTRL 0x6 +#define TPS62361_REG_ADDR_CHIP_ID 0x8 +#define TPS62361_REG_ADDR_CHIP_ID_2 0x9 + +#define TPS62361_BASE_VOLT_MV 500 +#define TPS62361_VSEL0_GPIO 7 + /* Defines for DPLL setup */ #define DPLL_LOCKED_FREQ_TOLERANCE_0 0 #define DPLL_LOCKED_FREQ_TOLERANCE_500_KHZ 500 diff --git a/arch/arm/include/asm/arch-omap4/mux_omap4.h b/arch/arm/include/asm/arch-omap4/mux_omap4.h index 019574b..30bfad7 100644 --- a/arch/arm/include/asm/arch-omap4/mux_omap4.h +++ b/arch/arm/include/asm/arch-omap4/mux_omap4.h @@ -341,4 +341,5 @@ struct pad_conf_entry { #define CONTROL_SPARE_R 0x0618 #define CONTROL_SPARE_R_C0 0x061C
+#define CONTROL_WKUP_PAD1_FREF_CLK4_REQ 0x4A31E05A #endif /* _MUX_OMAP4_H_ */