The Turris Omnia is a open-source router created by CZ.NIC.
The code is based on the Marvell/db-88f6820-gp by Stefan Roese with modifications from Tomas Hlavacek in the CZ.NIC turris-omnia-uboot repository, which can be found at https://gitlab.labs.nic.cz/turris/turris-omnia-uboot
By default, the Turris Omnia uses btrfs as the main and only filesystem, and also loads kernel and device tree from this filesystem. Since U-Boot does not yet support btrfs, you should not flash your Turris Omnia board with this unless you know what you are doing.
Signed-off-by: Tomas Hlavacek tomas.hlavacek@nic.cz Signed-off-by: Marek Behun marek.behun@nic.cz
create mode 100644 board/CZ.NIC/turris_omnia/Makefile create mode 100644 board/CZ.NIC/turris_omnia/kwbimage.cfg create mode 100644 board/CZ.NIC/turris_omnia/turris_omnia.c create mode 100644 configs/turris_omnia_defconfig create mode 100644 include/configs/turris_omnia.h
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index 6ae54ef46a..6b16f57464 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -90,6 +90,10 @@ config TARGET_DB_88F6820_AMC bool "Support DB-88F6820-AMC" select 88F6820
+config TARGET_TURRIS_OMNIA + bool "Support Turris Omnia" + select 88F6820 + config TARGET_MVEBU_ARMADA_8K bool "Support Armada 7k/8k platforms" select ARMADA_8K @@ -124,6 +128,7 @@ config SYS_BOARD default "db-88f6720" if TARGET_DB_88F6720 default "db-88f6820-gp" if TARGET_DB_88F6820_GP default "db-88f6820-amc" if TARGET_DB_88F6820_AMC + default "turris_omnia" if TARGET_TURRIS_OMNIA default "mvebu_armada-8k" if TARGET_MVEBU_ARMADA_8K default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP default "ds414" if TARGET_DS414 @@ -141,6 +146,7 @@ config SYS_CONFIG_NAME default "ds414" if TARGET_DS414 default "maxbcm" if TARGET_MAXBCM default "theadorable" if TARGET_THEADORABLE + default "turris_omnia" if TARGET_TURRIS_OMNIA
config SYS_VENDOR default "Marvell" if TARGET_DB_MV784MP_GP @@ -151,10 +157,26 @@ config SYS_VENDOR default "Marvell" if TARGET_MVEBU_ARMADA_8K default "solidrun" if TARGET_CLEARFOG default "Synology" if TARGET_DS414 + default "CZ.NIC" if TARGET_TURRIS_OMNIA
config SYS_SOC default "mvebu"
+if TARGET_TURRIS_OMNIA + +choice + prompt "Turris Omnia boot method" + +config TURRIS_OMNIA_SPL_BOOT_DEVICE_SPI + bool "SPI NOR flash" + +config TURRIS_OMNIA_SPL_BOOT_DEVICE_MMC + bool "SDIO/MMC card" + +endchoice + +endif + config MVEBU_EFUSE bool "Enable eFuse support" default n diff --git a/board/CZ.NIC/turris_omnia/Makefile b/board/CZ.NIC/turris_omnia/Makefile new file mode 100644 index 0000000000..f2ae50654f --- /dev/null +++ b/board/CZ.NIC/turris_omnia/Makefile @@ -0,0 +1,7 @@ +# +# Copyright (C) 2017 Marek Behun marek.behun@nic.cz +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := turris_omnia.o diff --git a/board/CZ.NIC/turris_omnia/kwbimage.cfg b/board/CZ.NIC/turris_omnia/kwbimage.cfg new file mode 100644 index 0000000000..cc05792556 --- /dev/null +++ b/board/CZ.NIC/turris_omnia/kwbimage.cfg @@ -0,0 +1,12 @@ +# +# Copyright (C) 2014 Stefan Roese sr@denx.de +# + +# Armada XP uses version 1 image format +VERSION 1 + +# Boot Media configurations +BOOT_FROM spi + +# Binary Header (bin_hdr) with DDR3 training code +BINARY spl/u-boot-spl.bin 0000005b 00000068 diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c new file mode 100644 index 0000000000..86926f8050 --- /dev/null +++ b/board/CZ.NIC/turris_omnia/turris_omnia.c @@ -0,0 +1,530 @@ +/* + * Copyright (C) 2017 Marek Behun marek.behun@nic.cz + * Copyright (C) 2016 Tomas Hlavacek tomas.hlavacek@nic.cz + * + * Derived from the code for + * Marvell/db-88f6820-gp by Stefan Roese sr@denx.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <miiphy.h> +#include <netdev.h> +#include <asm/io.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> +#include <dm/uclass.h> +#include <fdt_support.h> +#include <time.h> + +#ifdef CONFIG_ATSHA204A +# include <atsha204a-i2c.h> +#endif + +#ifdef CONFIG_WDT_ORION +# include <wdt.h> +#endif + +#include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h" +#include <../serdes/a38x/high_speed_env_spec.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define OMNIA_I2C_EEPROM_DM_NAME "i2c@0" +#define OMNIA_I2C_EEPROM 0x54 +#define OMNIA_I2C_EEPROM_CONFIG_ADDR 0x0 +#define OMNIA_I2C_EEPROM_ADDRLEN 2 +#define OMNIA_I2C_EEPROM_MAGIC 0x0341a034 + +#define OMNIA_I2C_MCU_DM_NAME "i2c@0" +#define OMNIA_I2C_MCU_ADDR_STATUS 0x1 +#define OMNIA_I2C_MCU_SATA 0x20 +#define OMNIA_I2C_MCU_CARDDET 0x10 +#define OMNIA_I2C_MCU 0x2a +#define OMNIA_I2C_MCU_WDT_ADDR 0x0b + +#define OMNIA_ATSHA204_OTP_VERSION 0 +#define OMNIA_ATSHA204_OTP_SERIAL 1 +#define OMNIA_ATSHA204_OTP_MAC0 3 +#define OMNIA_ATSHA204_OTP_MAC1 4 + +#define MVTWSI_ARMADA_DEBUG_REG 0x8c + +/* + * Those values and defines are taken from the Marvell U-Boot version + * "u-boot-2013.01-2014_T3.0" + */ +#define OMNIA_GPP_OUT_ENA_LOW \ + (~(BIT(1) | BIT(4) | BIT(6) | BIT(7) | BIT(8) | BIT(9) | \ + BIT(10) | BIT(11) | BIT(19) | BIT(22) | BIT(23) | BIT(25) | \ + BIT(26) | BIT(27) | BIT(29) | BIT(30) | BIT(31))) +#define OMNIA_GPP_OUT_ENA_MID \ + (~(BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(15) | \ + BIT(16) | BIT(17) | BIT(18))) + +#define OMNIA_GPP_OUT_VAL_LOW 0x0 +#define OMNIA_GPP_OUT_VAL_MID 0x0 +#define OMNIA_GPP_POL_LOW 0x0 +#define OMNIA_GPP_POL_MID 0x0 + +static struct serdes_map board_serdes_map_pex[] = { + {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, + {USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, + {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, + {SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0} +}; + +static struct serdes_map board_serdes_map_sata[] = { + {SATA0, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, + {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, + {SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0} +}; + +static bool omnia_detect_sata(void) +{ + struct udevice *bus, *dev; + int ret; + u16 mode; + + puts("SERDES0 card detect: "); + + if (uclass_get_device_by_name(UCLASS_I2C, OMNIA_I2C_MCU_DM_NAME, &bus)) { + puts("Cannot find MCU bus!\n"); + return false; + } + + ret = i2c_get_chip(bus, OMNIA_I2C_MCU, 1, &dev); + if (ret) { + puts("Cannot get MCU chip!\n"); + return false; + } + + ret = dm_i2c_read(dev, OMNIA_I2C_MCU_ADDR_STATUS, (uchar *) &mode, 2); + if (ret) { + puts("I2C read failed! Default PEX\n"); + return false; + } + + if (!(mode & OMNIA_I2C_MCU_CARDDET)) { + puts("NONE\n"); + return false; + } + + if (mode & OMNIA_I2C_MCU_SATA) { + puts("SATA\n"); + return true; + } else { + puts("PEX\n"); + return false; + } +} + +int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) +{ + if (omnia_detect_sata()) { + *serdes_map_array = board_serdes_map_sata; + *count = ARRAY_SIZE(board_serdes_map_sata); + } else { + *serdes_map_array = board_serdes_map_pex; + *count = ARRAY_SIZE(board_serdes_map_pex); + } + + return 0; +} + +struct omnia_eeprom { + u32 magic; + u32 ramsize; + char region[4]; + u32 crc; +}; + +static bool omnia_read_eeprom(struct omnia_eeprom *oep) +{ + struct udevice *bus, *dev; + int ret, crc, retry = 3; + + if (uclass_get_device_by_name(UCLASS_I2C, OMNIA_I2C_EEPROM_DM_NAME, &bus)) { + puts("Cannot find EEPROM bus\n"); + return false; + } + + ret = i2c_get_chip(bus, OMNIA_I2C_EEPROM, OMNIA_I2C_EEPROM_ADDRLEN, &dev); + if (ret) { + puts("Cannot get EEPROM chip\n"); + return false; + } + + for (; retry > 0; --retry) { + ret = dm_i2c_read(dev, OMNIA_I2C_EEPROM_CONFIG_ADDR, (uchar *) oep, sizeof(struct omnia_eeprom)); + if (ret) + continue; + + if (oep->magic != OMNIA_I2C_EEPROM_MAGIC) { + puts("I2C EEPROM missing magic number!\n"); + continue; + } + + crc = crc32(0, (unsigned char *) oep, + sizeof(struct omnia_eeprom) - 4); + if (crc == oep->crc) { + break; + } else { + printf("CRC of EEPROM memory config failed! " + "calc=0x%04x saved=0x%04x\n", crc, oep->crc); + } + } + + if (!retry) { + puts("I2C EEPROM read failed!\n"); + return false; + } + + return true; +} + +/* + * Define the DDR layout / topology here in the board file. This will + * be used by the DDR3 init code in the SPL U-Boot version to configure + * the DDR3 controller. + */ +static struct hws_topology_map board_topology_map_1g = { + 0x1, /* active interfaces */ + /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */ + { { { {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0} }, + SPEED_BIN_DDR_1600K, /* speed_bin */ + BUS_WIDTH_16, /* memory_width */ + MEM_4G, /* mem_size */ + DDR_FREQ_800, /* frequency */ + 0, 0, /* cas_l cas_wl */ + HWS_TEMP_NORMAL, /* temperature */ + HWS_TIM_2T} }, /* timing (force 2t) */ + 5, /* Num Of Bus Per Interface*/ + BUS_MASK_32BIT /* Busses mask */ +}; + +static struct hws_topology_map board_topology_map_2g = { + 0x1, /* active interfaces */ + /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */ + { { { {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0} }, + SPEED_BIN_DDR_1600K, /* speed_bin */ + BUS_WIDTH_16, /* memory_width */ + MEM_8G, /* mem_size */ + DDR_FREQ_800, /* frequency */ + 0, 0, /* cas_l cas_wl */ + HWS_TEMP_NORMAL, /* temperature */ + HWS_TIM_2T} }, /* timing (force 2t) */ + 5, /* Num Of Bus Per Interface*/ + BUS_MASK_32BIT /* Busses mask */ +}; + +struct hws_topology_map *ddr3_get_topology_map(void) +{ + static int mem = 0; + struct omnia_eeprom oep; + + /* Get the board config from EEPROM */ + if (mem == 0) { + if(!omnia_read_eeprom(&oep)) + goto out; + + printf("Memory config in EEPROM: 0x%02x\n", oep.ramsize); + + if (oep.ramsize == 0x2) + mem = 2; + else + mem = 1; + } + +out: + /* Hardcoded fallback */ + if (mem == 0) { + puts("WARNING: Memory config from EEPROM read failed.\n"); + puts("Falling back to default 1GiB map.\n"); + mem = 1; + } + + /* Return the board topology as defined in the board code */ + if (mem == 1) + return &board_topology_map_1g; + if (mem == 2) + return &board_topology_map_2g; + + return &board_topology_map_1g; +} + +#ifndef CONFIG_SPL_BUILD +static int set_regdomain(void) +{ + struct omnia_eeprom oep; + char rd[3] = {' ', ' ', 0}; + + if (omnia_read_eeprom(&oep)) + memcpy(rd, &oep.region, 2); + else + puts("EEPROM regdomain read failed.\n"); + + printf("Regdomain set to %s\n", rd); + return setenv("regdomain", rd); +} +#endif + +int board_early_init_f(void) +{ + u32 i2c_debug_reg; + + /* Configure MPP */ + writel(0x11111111, MVEBU_MPP_BASE + 0x00); + writel(0x11111111, MVEBU_MPP_BASE + 0x04); + writel(0x11244011, MVEBU_MPP_BASE + 0x08); + writel(0x22222111, MVEBU_MPP_BASE + 0x0c); + writel(0x22200002, MVEBU_MPP_BASE + 0x10); + writel(0x30042022, MVEBU_MPP_BASE + 0x14); + writel(0x55550555, MVEBU_MPP_BASE + 0x18); + writel(0x00005550, MVEBU_MPP_BASE + 0x1c); + + /* Set GPP Out value */ + writel(OMNIA_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00); + writel(OMNIA_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00); + + /* Set GPP Polarity */ + writel(OMNIA_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c); + writel(OMNIA_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c); + + /* Set GPP Out Enable */ + writel(OMNIA_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04); + writel(OMNIA_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04); + + /* Disable I2C debug mode blocking 0x64 I2C address */ + i2c_debug_reg = readl(MVEBU_TWSI_BASE + MVTWSI_ARMADA_DEBUG_REG); + i2c_debug_reg &= ~(1<<18); + writel(i2c_debug_reg, MVEBU_TWSI_BASE + MVTWSI_ARMADA_DEBUG_REG); + + return 0; +} + +#ifndef CONFIG_SPL_BUILD +static bool disable_mcu_watchdog(void) +{ + struct udevice *bus, *dev; + int ret, retry = 3; + uchar buf[1] = {0x0}; + + if (uclass_get_device_by_name(UCLASS_I2C, OMNIA_I2C_MCU_DM_NAME, &bus)) { + puts("Cannot find MCU bus! Can not disable MCU WDT.\n"); + return false; + } + + ret = i2c_get_chip(bus, OMNIA_I2C_MCU, 1, &dev); + if (ret) { + puts("Cannot get MCU chip! Can not disable MCU WDT.\n"); + return false; + } + + for (; retry > 0; --retry) + if (!dm_i2c_write(dev, OMNIA_I2C_MCU_WDT_ADDR, (uchar *) buf, 1)) + break; + + if (retry <= 0) { + puts("I2C MCU watchdog failed to disable!\n"); + return false; + } + + return true; +} +#endif + +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) +static struct udevice *watchdog_dev = NULL; +#endif + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + +#ifndef CONFIG_SPL_BUILD +# ifdef CONFIG_WDT_ORION + if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { + puts("Cannot find Armada 385 watchdog!\n"); + } else { + puts("Enabling Armada 385 watchdog.\n"); + wdt_start(watchdog_dev, (u32) 25000000 * 120, 0); + } +# endif + + if (disable_mcu_watchdog()) + puts("Disabled MCU startup watchdog.\n"); + + set_regdomain(); +#endif + + return 0; +} + +#ifdef CONFIG_WATCHDOG +/* Called by macro WATCHDOG_RESET */ +void watchdog_reset(void) +{ +# if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) + static ulong next_reset = 0; + ulong now; + + if (!watchdog_dev) + return; + + now = timer_get_us(); + + /* Do not reset the watchdog too often */ + if (now > next_reset) { + wdt_reset(watchdog_dev); + next_reset = now + 1000; + } +# endif +} +#endif + +int board_late_init(void) +{ +#ifndef CONFIG_SPL_BUILD + set_regdomain(); +#endif + + return 0; +} + +#ifdef CONFIG_ATSHA204A +static struct udevice *get_atsha204a_dev(void) +{ + static struct udevice *dev = NULL; + + if (dev != NULL) + return dev; + + if (uclass_get_device_by_name(UCLASS_MISC, "atsha204a@64", &dev)) { + puts("Cannot find ATSHA204A on I2C bus!\n"); + dev = NULL; + } + + return dev; +} +#endif + +int checkboard(void) +{ + u32 version_num, serial_num; + int err = 1; + +#ifdef CONFIG_ATSHA204A + struct udevice *dev = get_atsha204a_dev(); + + if (dev) { + err = atsha204a_wakeup(dev); + if (err) + goto out; + + err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false, + OMNIA_ATSHA204_OTP_VERSION, + (u8 *) &version_num); + if (err) + goto out; + + err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false, + OMNIA_ATSHA204_OTP_SERIAL, + (u8 *) &serial_num); + if (err) + goto out; + + atsha204a_sleep(dev); + } + +out: +#endif + + if (err) + printf("Board: Turris Omnia (ver N/A). SN: N/A\n"); + else + printf("Board: Turris Omnia SNL %08X%08X\n", + be32_to_cpu(version_num), be32_to_cpu(serial_num)); + + return 0; +} + +static void increment_mac(u8 *mac) +{ + int i; + + for (i = 5; i >= 3; i--) { + mac[i] += 1; + if (mac[i]) + break; + } +} + +int misc_init_r(void) +{ +#ifdef CONFIG_ATSHA204A + int err; + struct udevice *dev = get_atsha204a_dev(); + u8 mac0[4], mac1[4], mac[6]; + + if (!dev) + goto out; + + err = atsha204a_wakeup(dev); + if (err) + goto out; + + err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false, + OMNIA_ATSHA204_OTP_MAC0, mac0); + if (err) + goto out; + + err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false, + OMNIA_ATSHA204_OTP_MAC1, mac1); + if (err) + goto out; + + atsha204a_sleep(dev); + + mac[0] = mac0[1]; + mac[1] = mac0[2]; + mac[2] = mac0[3]; + mac[3] = mac1[1]; + mac[4] = mac1[2]; + mac[5] = mac1[3]; + + if (is_valid_ethaddr(mac)) + eth_setenv_enetaddr("ethaddr", mac); + + increment_mac(mac); + + if (is_valid_ethaddr(mac)) + eth_setenv_enetaddr("eth1addr", mac); + + increment_mac(mac); + + if (is_valid_ethaddr(mac)) + eth_setenv_enetaddr("eth2addr", mac); + +out: +#endif + + return 0; +} + diff --git a/configs/turris_omnia_defconfig b/configs/turris_omnia_defconfig new file mode 100644 index 0000000000..512b9da74d --- /dev/null +++ b/configs/turris_omnia_defconfig @@ -0,0 +1,62 @@ +CONFIG_ARM=y +CONFIG_ARCH_MVEBU=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_TARGET_TURRIS_OMNIA=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI_SUPPORT=y +CONFIG_SPL_BOOT_DEVICE_SPI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_DEFAULT_DEVICE_TREE="armada-385-turris-omnia" +CONFIG_BOOTDELAY=3 +CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_SPL=y +CONFIG_SPL_I2C_SUPPORT=y +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_I2C=y +CONFIG_CMD_USB=y +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_GO=y +CONFIG_CMD_RUN=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SAVEENV=y +CONFIG_CMD_LOADB=y +CONFIG_CMD_LOADS=y +CONFIG_CMD_MEMORY=y +CONFIG_CMD_ECHO=y +CONFIG_CMD_SETEXPR=y +# CONFIG_PARTITION_UUIDS is not set +# CONFIG_SPL_PARTITION_UUIDS is not set +CONFIG_DOS_PARTITION=y +CONFIG_SPL_OF_TRANSLATE=y +CONFIG_MISC=y +CONFIG_ATSHA204A=y +CONFIG_DEBUG_UART=y +CONFIG_DEBUG_UART_NS16550=y +CONFIG_DEBUG_UART_BASE=0xd0012000 +CONFIG_DEBUG_UART_CLOCK=250000000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_MV=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI=y +CONFIG_USB_EHCI_MARVELL=y +CONFIG_USB_STORAGE=y +CONFIG_WDT=y +CONFIG_WDT_ORION=y +CONFIG_ARCH_MISC_INIT=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_CMDLINE=y +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="=> " +# CONFIG_DISPLAY_BOARDINFO is not set diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h new file mode 100644 index 0000000000..4ad603d2fb --- /dev/null +++ b/include/configs/turris_omnia.h @@ -0,0 +1,178 @@ +/* + * Copyright (C) 2017 Marek Behun marek.behun@nic.cz + * Copyright (C) 2016 Tomas Hlavacek tomas.hlavacek@nic.cz + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_TURRIS_OMNIA_H +#define _CONFIG_TURRIS_OMNIA_H + +/* + * High Level Configuration Options (easy to change) + */ + +#define CONFIG_MISC_INIT_R +#define CONFIG_DISPLAY_BOARDINFO_LATE + +/* + * TEXT_BASE needs to be below 16MiB, since this area is scrubbed + * for DDR ECC byte filling in the SPL before loading the main + * U-Boot into it. + */ +#define CONFIG_SYS_TEXT_BASE 0x00800000 +#define CONFIG_SYS_TCLK 250000000 /* 250MHz */ + +/* + * Commands configuration + */ +#define CONFIG_CMD_PCI + +/* I2C support */ +#define CONFIG_DM_I2C +#define CONFIG_I2C_MUX +#define CONFIG_I2C_MUX_PCA954x +#define CONFIG_SPL_I2C_MUX +#define CONFIG_SYS_I2C_MVTWSI + +/* Watchdog support */ +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) +# define CONFIG_WATCHDOG +#endif + +/* SPI NOR flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_SPEED 1000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SPANSION + +/* + * SDIO/MMC Card Configuration + */ +#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE + +/* + * SATA/SCSI/AHCI configuration + */ +#define CONFIG_LIBATA +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + +/* Additional FS support/configuration */ +#define CONFIG_SUPPORT_VFAT + +/* USB/EHCI configuration */ +#define CONFIG_EHCI_IS_TDI + +/* Environment in SPI NOR flash */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET (3*(1 << 18)) /* 768KiB in */ +#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ +#define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ + +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ +#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ + +/* PCIe support */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_PCI_MVEBU +#define CONFIG_PCI_SCAN_SHOW +#endif + +#define CONFIG_SYS_ALT_MEMTEST + +/* Keep device tree and initrd in lower memory so the kernel can access them */ +#define RELOCATION_LIMITS_ENV_SETTINGS \ + "fdt_high=0x10000000\0" \ + "initrd_high=0x10000000\0" + +/* Defines for SPL */ +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_SIZE (140 << 10) +#define CONFIG_SPL_TEXT_BASE 0x40000030 +#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) + +#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) +#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MALLOC_SIMPLE +#endif + +#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) +#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT + +#ifdef CONFIG_TURRIS_OMNIA_SPL_BOOT_DEVICE_SPI +/* SPL related SPI defines */ +# define CONFIG_SPL_SPI_LOAD +# define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000 +# define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS +#endif + +#ifdef CONFIG_TURRIS_OMNIA_SPL_BOOT_DEVICE_MMC +/* SPL related MMC defines */ +# define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10) +# define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS +# ifdef CONFIG_SPL_BUILD +# define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */ +# endif +#endif + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* Include the common distro boot environment */ +#ifndef CONFIG_SPL_BUILD +#include <config_distro_defaults.h> + +#ifdef CONFIG_MMC +#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) +#else +#define BOOT_TARGET_DEVICES_MMC(func) +#endif + +#ifdef CONFIG_USB_STORAGE +#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) +#else +#define BOOT_TARGET_DEVICES_USB(func) +#endif + +#define BOOT_TARGET_DEVICES(func) \ + BOOT_TARGET_DEVICES_MMC(func) \ + BOOT_TARGET_DEVICES_USB(func) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) + +#define KERNEL_ADDR_R __stringify(0x1000000) +#define FDT_ADDR_R __stringify(0x2000000) +#define RAMDISK_ADDR_R __stringify(0x2200000) +#define SCRIPT_ADDR_R __stringify(0x1800000) +#define PXEFILE_ADDR_R __stringify(0x1900000) + +#define LOAD_ADDRESS_ENV_SETTINGS \ + "kernel_addr_r=" KERNEL_ADDR_R "\0" \ + "fdt_addr_r=" FDT_ADDR_R "\0" \ + "ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \ + "scriptaddr=" SCRIPT_ADDR_R "\0" \ + "pxefile_addr_r=" PXEFILE_ADDR_R "\0" + +#include <config_distro_bootcmd.h> + +#define CONFIG_EXTRA_ENV_SETTINGS \ + RELOCATION_LIMITS_ENV_SETTINGS \ + LOAD_ADDRESS_ENV_SETTINGS \ + "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ + "console=ttyS0,115200\0" \ + BOOTENV + +#endif /* CONFIG_SPL_BUILD */ + +#endif /* _CONFIG_TURRIS_OMNIA_H */