From: "Govindraj.R" govindraj.raja@ti.com
usb dpll configuration is done only part of non-essential dppl configuration however if CONFIG_USB_EHCI_OMAP is defined we may have to configure usb dpll's for proper functioning of usb modules. So move the usb dppl configuration to a new func. and utilise the same during essential dpll configuration.
Signed-off-by: Govindraj.R govindraj.raja@ti.com --- arch/arm/cpu/armv7/omap-common/clocks-common.c | 52 ++++++++++++++--------- 1 files changed, 32 insertions(+), 20 deletions(-)
diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 1da90a4..770ac19 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -251,6 +251,33 @@ void configure_mpu_dpll(void) debug("MPU DPLL locked\n"); }
+static void setup_usb_dpll(void) +{ + const struct dpll_params *params; + u32 sys_clk_khz, sd_div, num, den; + + sys_clk_khz = get_sys_clk_freq() / 1000; + /* + * USB: + * USB dpll is J-type. Need to set DPLL_SD_DIV for jitter correction + * DPLL_SD_DIV = CEILING ([DPLL_MULT/(DPLL_DIV+1)]* CLKINP / 250) + * - where CLKINP is sys_clk in MHz + * Use CLKINP in KHz and adjust the denominator accordingly so + * that we have enough accuracy and at the same time no overflow + */ + params = get_usb_dpll_params(); + num = params->m * sys_clk_khz; + den = (params->n + 1) * 250 * 1000; + num += den - 1; + sd_div = num / den; + clrsetbits_le32(&prcm->cm_clksel_dpll_usb, + CM_CLKSEL_DPLL_DPLL_SD_DIV_MASK, + sd_div << CM_CLKSEL_DPLL_DPLL_SD_DIV_SHIFT); + + /* Now setup the dpll with the regular function */ + do_setup_dpll(&prcm->cm_clkmode_dpll_usb, params, DPLL_LOCK, "usb"); +} + static void setup_dplls(void) { u32 temp; @@ -282,13 +309,16 @@ static void setup_dplls(void)
/* MPU dpll */ configure_mpu_dpll(); + +#ifdef CONFIG_USB_EHCI_OMAP + setup_usb_dpll(); +#endif }
#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL static void setup_non_essential_dplls(void) { u32 sys_clk_khz, abe_ref_clk; - u32 sd_div, num, den; const struct dpll_params *params;
sys_clk_khz = get_sys_clk_freq() / 1000; @@ -300,25 +330,7 @@ static void setup_non_essential_dplls(void) params = get_iva_dpll_params(); do_setup_dpll(&prcm->cm_clkmode_dpll_iva, params, DPLL_LOCK, "iva");
- /* - * USB: - * USB dpll is J-type. Need to set DPLL_SD_DIV for jitter correction - * DPLL_SD_DIV = CEILING ([DPLL_MULT/(DPLL_DIV+1)]* CLKINP / 250) - * - where CLKINP is sys_clk in MHz - * Use CLKINP in KHz and adjust the denominator accordingly so - * that we have enough accuracy and at the same time no overflow - */ - params = get_usb_dpll_params(); - num = params->m * sys_clk_khz; - den = (params->n + 1) * 250 * 1000; - num += den - 1; - sd_div = num / den; - clrsetbits_le32(&prcm->cm_clksel_dpll_usb, - CM_CLKSEL_DPLL_DPLL_SD_DIV_MASK, - sd_div << CM_CLKSEL_DPLL_DPLL_SD_DIV_SHIFT); - - /* Now setup the dpll with the regular function */ - do_setup_dpll(&prcm->cm_clkmode_dpll_usb, params, DPLL_LOCK, "usb"); + setup_usb_dpll();
/* Configure ABE dpll */ params = get_abe_dpll_params();