DRAM chip varies, and one code cannot satisfy all DRAMs.
Add options to select a timing set.
Currently only DDR3-1333 (the original set) is added into it.
Signed-off-by: Icenowy Zheng icenowy@aosc.xyz --- arch/arm/include/asm/arch-sunxi/dram_sunxi_dw.h | 30 ++++++ arch/arm/mach-sunxi/Makefile | 1 + arch/arm/mach-sunxi/dram_sunxi_dw.c | 116 ++---------------------- arch/arm/mach-sunxi/dram_timings/Makefile | 1 + arch/arm/mach-sunxi/dram_timings/ddr3_1333.c | 84 +++++++++++++++++ board/sunxi/Kconfig | 18 ++++ 6 files changed, 140 insertions(+), 110 deletions(-) create mode 100644 arch/arm/mach-sunxi/dram_timings/Makefile create mode 100644 arch/arm/mach-sunxi/dram_timings/ddr3_1333.c
diff --git a/arch/arm/include/asm/arch-sunxi/dram_sunxi_dw.h b/arch/arm/include/asm/arch-sunxi/dram_sunxi_dw.h index 48bd6f7c0f..61da150c14 100644 --- a/arch/arm/include/asm/arch-sunxi/dram_sunxi_dw.h +++ b/arch/arm/include/asm/arch-sunxi/dram_sunxi_dw.h @@ -191,4 +191,34 @@ struct sunxi_mctl_ctl_reg { #define DXBDLR_WRITE_DELAY(x) ((x) << 8) #define DXBDLR_READ_DELAY(x) ((x) << 0)
+/* + * The delay parameters below allow to allegedly specify delay times of some + * unknown unit for each individual bit trace in each of the four data bytes + * the 32-bit wide access consists of. Also three control signals can be + * adjusted individually. + */ +#define BITS_PER_BYTE 8 +#define NR_OF_BYTE_LANES (32 / BITS_PER_BYTE) +/* The eight data lines (DQn) plus DM, DQS and DQSN */ +#define LINES_PER_BYTE_LANE (BITS_PER_BYTE + 3) +struct dram_para { + u16 page_size; + u8 bus_full_width; + u8 dual_rank; + u8 row_bits; + u8 bank_bits; + const u8 dx_read_delays[NR_OF_BYTE_LANES][LINES_PER_BYTE_LANE]; + const u8 dx_write_delays[NR_OF_BYTE_LANES][LINES_PER_BYTE_LANE]; + const u8 ac_delays[31]; +}; + +static inline int ns_to_t(int nanoseconds) +{ + const unsigned int ctrl_freq = CONFIG_DRAM_CLK / 2; + + return DIV_ROUND_UP(ctrl_freq * nanoseconds, 1000); +} + +void mctl_set_timing_params(uint16_t socid, struct dram_para *para); + #endif /* _SUNXI_DRAM_SUN8I_H3_H */ diff --git a/arch/arm/mach-sunxi/Makefile b/arch/arm/mach-sunxi/Makefile index b8f01e3b61..e1b6fe8d5c 100644 --- a/arch/arm/mach-sunxi/Makefile +++ b/arch/arm/mach-sunxi/Makefile @@ -49,6 +49,7 @@ obj-$(CONFIG_MACH_SUN8I_A23) += dram_sun8i_a23.o obj-$(CONFIG_MACH_SUN8I_A33) += dram_sun8i_a33.o obj-$(CONFIG_MACH_SUN8I_A83T) += dram_sun8i_a83t.o obj-$(CONFIG_SUNXI_DRAM_DW) += dram_sunxi_dw.o +obj-$(CONFIG_SUNXI_DRAM_DW) += dram_timings/ obj-$(CONFIG_MACH_SUN9I) += dram_sun9i.o obj-$(CONFIG_MACH_SUN50I) += dram_sun8i_h3.o endif diff --git a/arch/arm/mach-sunxi/dram_sunxi_dw.c b/arch/arm/mach-sunxi/dram_sunxi_dw.c index bb4457d2b8..401f6a4624 100644 --- a/arch/arm/mach-sunxi/dram_sunxi_dw.c +++ b/arch/arm/mach-sunxi/dram_sunxi_dw.c @@ -16,34 +16,6 @@ #include <asm/arch/cpu.h> #include <linux/kconfig.h>
-/* - * The delay parameters below allow to allegedly specify delay times of some - * unknown unit for each individual bit trace in each of the four data bytes - * the 32-bit wide access consists of. Also three control signals can be - * adjusted individually. - */ -#define BITS_PER_BYTE 8 -#define NR_OF_BYTE_LANES (32 / BITS_PER_BYTE) -/* The eight data lines (DQn) plus DM, DQS and DQSN */ -#define LINES_PER_BYTE_LANE (BITS_PER_BYTE + 3) -struct dram_para { - u16 page_size; - u8 bus_full_width; - u8 dual_rank; - u8 row_bits; - u8 bank_bits; - const u8 dx_read_delays[NR_OF_BYTE_LANES][LINES_PER_BYTE_LANE]; - const u8 dx_write_delays[NR_OF_BYTE_LANES][LINES_PER_BYTE_LANE]; - const u8 ac_delays[31]; -}; - -static inline int ns_to_t(int nanoseconds) -{ - const unsigned int ctrl_freq = CONFIG_DRAM_CLK / 2; - - return DIV_ROUND_UP(ctrl_freq * nanoseconds, 1000); -} - static void mctl_phy_init(u32 val) { struct sunxi_mctl_ctl_reg * const mctl_ctl = @@ -190,87 +162,6 @@ static void mctl_set_master_priority(uint16_t socid) } }
-static void mctl_set_timing_params(uint16_t socid, struct dram_para *para) -{ - struct sunxi_mctl_ctl_reg * const mctl_ctl = - (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE; - - u8 tccd = 2; - u8 tfaw = ns_to_t(50); - u8 trrd = max(ns_to_t(10), 4); - u8 trcd = ns_to_t(15); - u8 trc = ns_to_t(53); - u8 txp = max(ns_to_t(8), 3); - u8 twtr = max(ns_to_t(8), 4); - u8 trtp = max(ns_to_t(8), 4); - u8 twr = max(ns_to_t(15), 3); - u8 trp = ns_to_t(15); - u8 tras = ns_to_t(38); - u16 trefi = ns_to_t(7800) / 32; - u16 trfc = ns_to_t(350); - - u8 tmrw = 0; - u8 tmrd = 4; - u8 tmod = 12; - u8 tcke = 3; - u8 tcksrx = 5; - u8 tcksre = 5; - u8 tckesr = 4; - u8 trasmax = 24; - - u8 tcl = 6; /* CL 12 */ - u8 tcwl = 4; /* CWL 8 */ - u8 t_rdata_en = 4; - u8 wr_latency = 2; - - u32 tdinit0 = (500 * CONFIG_DRAM_CLK) + 1; /* 500us */ - u32 tdinit1 = (360 * CONFIG_DRAM_CLK) / 1000 + 1; /* 360ns */ - u32 tdinit2 = (200 * CONFIG_DRAM_CLK) + 1; /* 200us */ - u32 tdinit3 = (1 * CONFIG_DRAM_CLK) + 1; /* 1us */ - - u8 twtp = tcwl + 2 + twr; /* WL + BL / 2 + tWR */ - u8 twr2rd = tcwl + 2 + twtr; /* WL + BL / 2 + tWTR */ - u8 trd2wr = tcl + 2 + 1 - tcwl; /* RL + BL / 2 + 2 - WL */ - - /* set mode register */ - writel(0x1c70, &mctl_ctl->mr[0]); /* CL=11, WR=12 */ - writel(0x40, &mctl_ctl->mr[1]); - writel(0x18, &mctl_ctl->mr[2]); /* CWL=8 */ - writel(0x0, &mctl_ctl->mr[3]); - - /* set DRAM timing */ - writel(DRAMTMG0_TWTP(twtp) | DRAMTMG0_TFAW(tfaw) | - DRAMTMG0_TRAS_MAX(trasmax) | DRAMTMG0_TRAS(tras), - &mctl_ctl->dramtmg[0]); - writel(DRAMTMG1_TXP(txp) | DRAMTMG1_TRTP(trtp) | DRAMTMG1_TRC(trc), - &mctl_ctl->dramtmg[1]); - writel(DRAMTMG2_TCWL(tcwl) | DRAMTMG2_TCL(tcl) | - DRAMTMG2_TRD2WR(trd2wr) | DRAMTMG2_TWR2RD(twr2rd), - &mctl_ctl->dramtmg[2]); - writel(DRAMTMG3_TMRW(tmrw) | DRAMTMG3_TMRD(tmrd) | DRAMTMG3_TMOD(tmod), - &mctl_ctl->dramtmg[3]); - writel(DRAMTMG4_TRCD(trcd) | DRAMTMG4_TCCD(tccd) | DRAMTMG4_TRRD(trrd) | - DRAMTMG4_TRP(trp), &mctl_ctl->dramtmg[4]); - writel(DRAMTMG5_TCKSRX(tcksrx) | DRAMTMG5_TCKSRE(tcksre) | - DRAMTMG5_TCKESR(tckesr) | DRAMTMG5_TCKE(tcke), - &mctl_ctl->dramtmg[5]); - - /* set two rank timing */ - clrsetbits_le32(&mctl_ctl->dramtmg[8], (0xff << 8) | (0xff << 0), - (0x66 << 8) | (0x10 << 0)); - - /* set PHY interface timing, write latency and read latency configure */ - writel((0x2 << 24) | (t_rdata_en << 16) | (0x1 << 8) | - (wr_latency << 0), &mctl_ctl->pitmg[0]); - - /* set PHY timing, PTR0-2 use default */ - writel(PTR3_TDINIT0(tdinit0) | PTR3_TDINIT1(tdinit1), &mctl_ctl->ptr[3]); - writel(PTR4_TDINIT2(tdinit2) | PTR4_TDINIT3(tdinit3), &mctl_ctl->ptr[4]); - - /* set refresh timing */ - writel(RFSHTMG_TREFI(trefi) | RFSHTMG_TRFC(trfc), &mctl_ctl->rfshtmg); -} - static u32 bin_to_mgray(int val) { static const u8 lookup_table[32] = { @@ -367,7 +258,12 @@ static void mctl_set_cr(struct dram_para *para) struct sunxi_mctl_com_reg * const mctl_com = (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
- writel(MCTL_CR_BL8 | MCTL_CR_2T | MCTL_CR_DDR3 | MCTL_CR_INTERLEAVED | + writel(MCTL_CR_BL8 | MCTL_CR_2T | MCTL_CR_INTERLEAVED | +#if defined CONFIG_SUNXI_DRAM_DDR3 + MCTL_CR_DDR3 | +#else +#error Unsupported DRAM type! +#endif (para->bank_bits == 3 ? MCTL_CR_EIGHT_BANKS : MCTL_CR_FOUR_BANKS) | MCTL_CR_BUS_FULL_WIDTH(para->bus_full_width) | (para->dual_rank ? MCTL_CR_DUAL_RANK : MCTL_CR_SINGLE_RANK) | diff --git a/arch/arm/mach-sunxi/dram_timings/Makefile b/arch/arm/mach-sunxi/dram_timings/Makefile new file mode 100644 index 0000000000..7e71c76a5c --- /dev/null +++ b/arch/arm/mach-sunxi/dram_timings/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_SUNXI_DRAM_DDR3_1333) += ddr3_1333.o diff --git a/arch/arm/mach-sunxi/dram_timings/ddr3_1333.c b/arch/arm/mach-sunxi/dram_timings/ddr3_1333.c new file mode 100644 index 0000000000..8e082c735a --- /dev/null +++ b/arch/arm/mach-sunxi/dram_timings/ddr3_1333.c @@ -0,0 +1,84 @@ +#include <common.h> +#include <asm/arch/dram.h> +#include <asm/arch/cpu.h> + +void mctl_set_timing_params(uint16_t socid, struct dram_para *para) +{ + struct sunxi_mctl_ctl_reg * const mctl_ctl = + (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE; + + u8 tccd = 2; + u8 tfaw = ns_to_t(50); + u8 trrd = max(ns_to_t(10), 4); + u8 trcd = ns_to_t(15); + u8 trc = ns_to_t(53); + u8 txp = max(ns_to_t(8), 3); + u8 twtr = max(ns_to_t(8), 4); + u8 trtp = max(ns_to_t(8), 4); + u8 twr = max(ns_to_t(15), 3); + u8 trp = ns_to_t(15); + u8 tras = ns_to_t(38); + u16 trefi = ns_to_t(7800) / 32; + u16 trfc = ns_to_t(350); + + u8 tmrw = 0; + u8 tmrd = 4; + u8 tmod = 12; + u8 tcke = 3; + u8 tcksrx = 5; + u8 tcksre = 5; + u8 tckesr = 4; + u8 trasmax = 24; + + u8 tcl = 6; /* CL 12 */ + u8 tcwl = 4; /* CWL 8 */ + u8 t_rdata_en = 4; + u8 wr_latency = 2; + + u32 tdinit0 = (500 * CONFIG_DRAM_CLK) + 1; /* 500us */ + u32 tdinit1 = (360 * CONFIG_DRAM_CLK) / 1000 + 1; /* 360ns */ + u32 tdinit2 = (200 * CONFIG_DRAM_CLK) + 1; /* 200us */ + u32 tdinit3 = (1 * CONFIG_DRAM_CLK) + 1; /* 1us */ + + u8 twtp = tcwl + 2 + twr; /* WL + BL / 2 + tWR */ + u8 twr2rd = tcwl + 2 + twtr; /* WL + BL / 2 + tWTR */ + u8 trd2wr = tcl + 2 + 1 - tcwl; /* RL + BL / 2 + 2 - WL */ + + /* set mode register */ + writel(0x1c70, &mctl_ctl->mr[0]); /* CL=11, WR=12 */ + writel(0x40, &mctl_ctl->mr[1]); + writel(0x18, &mctl_ctl->mr[2]); /* CWL=8 */ + writel(0x0, &mctl_ctl->mr[3]); + + /* set DRAM timing */ + writel(DRAMTMG0_TWTP(twtp) | DRAMTMG0_TFAW(tfaw) | + DRAMTMG0_TRAS_MAX(trasmax) | DRAMTMG0_TRAS(tras), + &mctl_ctl->dramtmg[0]); + writel(DRAMTMG1_TXP(txp) | DRAMTMG1_TRTP(trtp) | DRAMTMG1_TRC(trc), + &mctl_ctl->dramtmg[1]); + writel(DRAMTMG2_TCWL(tcwl) | DRAMTMG2_TCL(tcl) | + DRAMTMG2_TRD2WR(trd2wr) | DRAMTMG2_TWR2RD(twr2rd), + &mctl_ctl->dramtmg[2]); + writel(DRAMTMG3_TMRW(tmrw) | DRAMTMG3_TMRD(tmrd) | DRAMTMG3_TMOD(tmod), + &mctl_ctl->dramtmg[3]); + writel(DRAMTMG4_TRCD(trcd) | DRAMTMG4_TCCD(tccd) | DRAMTMG4_TRRD(trrd) | + DRAMTMG4_TRP(trp), &mctl_ctl->dramtmg[4]); + writel(DRAMTMG5_TCKSRX(tcksrx) | DRAMTMG5_TCKSRE(tcksre) | + DRAMTMG5_TCKESR(tckesr) | DRAMTMG5_TCKE(tcke), + &mctl_ctl->dramtmg[5]); + + /* set two rank timing */ + clrsetbits_le32(&mctl_ctl->dramtmg[8], (0xff << 8) | (0xff << 0), + (0x66 << 8) | (0x10 << 0)); + + /* set PHY interface timing, write latency and read latency configure */ + writel((0x2 << 24) | (t_rdata_en << 16) | (0x1 << 8) | + (wr_latency << 0), &mctl_ctl->pitmg[0]); + + /* set PHY timing, PTR0-2 use default */ + writel(PTR3_TDINIT0(tdinit0) | PTR3_TDINIT1(tdinit1), &mctl_ctl->ptr[3]); + writel(PTR4_TDINIT2(tdinit2) | PTR4_TDINIT3(tdinit3), &mctl_ctl->ptr[4]); + + /* set refresh timing */ + writel(RFSHTMG_TREFI(trefi) | RFSHTMG_TRFC(trfc), &mctl_ctl->rfshtmg); +} diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index d8a1e341e8..7e03ee8b36 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -192,6 +192,24 @@ config ARM_BOOT_HOOK_RMR This allows both the SPL and the U-Boot proper to be entered in either mode and switch to AArch64 if needed.
+if SUNXI_DRAM_DW +config SUNXI_DRAM_DDR3 + bool + +choice + prompt "DRAM Type and Timing" + default SUNXI_DRAM_DDR3_1333 + +config SUNXI_DRAM_DDR3_1333 + bool "DDR3 1333" + select SUNXI_DRAM_DDR3 + ---help--- + This option is the original only supported memory type, which suits + many H3/H5/A64 boards available now. + +endchoice +endif + config DRAM_TYPE int "sunxi dram type" depends on MACH_SUN8I_A83T