Hi Josh,
On 05/20/2014 06:38 PM, Josh Wu wrote:
Enable mci0 support. And enable the mmc command in configuration file.
As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION, so remove the redundant CONFIG_DOS_PARTITION definition.
Signed-off-by: Josh Wu josh.wu@atmel.com
board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 28 +++++++++++++++++++++++ include/configs/at91sam9m10g45ek.h | 15 +++++++++++- 2 files changed, 42 insertions(+), 1 deletion(-)
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c index b7e2efd..fd6860b 100644 --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c @@ -15,7 +15,9 @@ #include <asm/arch/gpio.h> #include <asm/arch/clk.h> #include <lcd.h> +#include <mmc.h> #include <atmel_lcdc.h> +#include <atmel_mci.h> #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) #include <net.h> #endif @@ -217,6 +219,29 @@ void lcd_show_board_info(void) #endif /* CONFIG_LCD_INFO */ #endif
+#ifdef CONFIG_GENERIC_ATMEL_MCI +void at91sam9m10g45ek_mci_hw_init(void) +{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
- at91_set_a_periph(AT91_PIO_PORTA, 0, 0); /* MCI0 CLK */
- at91_set_a_periph(AT91_PIO_PORTA, 1, 0); /* MCI0 CDA */
- at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* MCI0 DB0 */
- at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* MCI0 DB1 */
- at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* MCI0 DB2 */
- at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* MCI0 DB3 */
The comments for pin should be DAx while not DBx.
- /* Enable clock */
- writel(1 << ATMEL_ID_MCI0, &pmc->pcer);
+}
+int board_mmc_init(bd_t *bis) +{
- at91_set_pio_input(AT91_PIO_PORTD, 10, 0); /* MCI0 CD */
As we won't use it, so I think we should remove it.
- return atmel_mci_init((void *)ATMEL_BASE_MCI0);
+} +#endif
- int board_early_init_f(void) { at91_seriald_hw_init();
@@ -247,6 +272,9 @@ int board_init(void) #ifdef CONFIG_ATMEL_SPI at91_spi0_hw_init(1 << 4); #endif +#ifdef CONFIG_GENERIC_ATMEL_MCI
- at91sam9m10g45ek_mci_hw_init();
+#endif #ifdef CONFIG_MACB at91sam9m10g45ek_macb_hw_init(); #endif diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h index ccfda71..df277e7 100644 --- a/include/configs/at91sam9m10g45ek.h +++ b/include/configs/at91sam9m10g45ek.h @@ -115,6 +115,20 @@
#endif
+/* MMC */ +#define CONFIG_CMD_MMC
+#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#endif
+#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif
- /* Ethernet */ #define CONFIG_MACB #define CONFIG_RMII
@@ -126,7 +140,6 @@ #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_ATMEL #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2 -#define CONFIG_DOS_PARTITION #define CONFIG_USB_STORAGE
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
Best Regards, Bo Shen